Frigidaire GLER642AS1 dryer Parts

On your Frigidaire dryer model GLER642AS1, the model number is printed on the serial plate located on the left side of the door opening. Open the dryer door and look along the inside edge of the cabinet opening for the label.

Quick steps to locate it

• Open the dryer door fully.
• Look on the left inside edge of the door opening (cabinet front).
• Find the serial plate label.
• Record both the model number and serial number for parts lookup and service.
• Keep the numbers with your purchase records for future reference.

What the label typically includes

Label item	What it’s used for
Model number (GLER642AS1)	Matching the correct parts diagrams and replacement parts
Serial number	Identifying production details for service and support
Date of purchase (your record)	Warranty and service documentation

Why it matters

Using the exact model number prevents ordering the wrong Frigidaire dryer parts (for example, a drum belt or thermostat that looks similar but does not fit). For model-specific identification details and care information, use the GLER642AS1 owner's manual.

Last updated: February 2026

Replacing the heating element in a Frigidaire dryer like model GLER642AS1 typically costs about $200 to $400 total (part plus labor). If you do it yourself, you usually pay just the part cost, which varies by the exact heater assembly used.

Typical cost breakdown

• Heating element part: commonly $100 to $200 for many Frigidaire electric dryers
• Labor (service call + install): commonly $100 to $200
• Total installed: commonly $200 to $400

Scenario	What you pay for	Typical total
DIY replacement	Heating element assembly only	$100 to $200
Technician replacement	Part + labor	$200 to $400

What affects the price most

• Correct part match for GLER642AS1 (heating element assemblies can look similar but wire differently)
• Access time (lint buildup, stuck fasteners, or tight cabinet clearances)
• Related heat issues that should be fixed at the same time (restricted venting, failed thermostats)

Smart checks before you buy a heater

A “no heat” complaint is not always a bad element. We recommend these quick checks first:

• Confirm the dryer is getting full power (many electric dryers can run but not heat if one leg of power is missing)
• Clean the lint screen and check for a crushed or clogged vent
• Look for signs of overheating; a blown thermal safety device often points to airflow problems
• Use the wiring diagram and test points in the GLER642AS1 owner’s manual

Why it matters

A restricted vent can overheat the heater circuit and repeatedly trip safety devices. Fixing airflow first helps the new heating element last longer and restores normal drying times.

Last updated: February 2026

For Frigidaire dryer model GLER642AS1, the most common “not drying” causes are restricted airflow (lint screen or vent/hood blockage) or a heat problem (failed heating circuit or overheating safety parts opening). Start with airflow checks, then move to heat and electrical checks using the GLER642AS1 owner's manual.

Quick checks that fix most “not drying” complaints

• Clean the lint screen completely before starting the cycle (every load).
• Check the outside exhaust hood; remove lint, nests, or a stuck flap.
• Inspect the vent duct: use 4-inch metal ducting, keep it as short as possible, and limit bends.
• Avoid overloading; heavy loads dry slowly and can trap moisture.
• If the dryer is electric, confirm it is on a full 240V supply (a 208V supply can dry about 20% slower).

Airflow vs. heat: how to tell what’s wrong

What you notice	Most likely issue	What to do next
Clothes are warm but still damp	Vent restriction or poor airflow	Clean lint screen, duct, and outside hood; shorten duct run
Clothes are cool and damp	No heat	Check heating circuit components and wiring
Dryer feels very hot, shuts down, or cycles oddly	Overheating protection opening	Clear venting first; then check thermostats/thermal limiter

Parts that commonly affect drying on GLER642AS1

If airflow is good and the dryer still will not dry, these parts are common suspects:

• Frigidaire dryer heating element assembly 131553900 (no heat)
• Dryer thermal limiter 134120900 (opens if overheating occurs)
• Electrolux dryer operating thermostat 134048800 (temperature control)
• Kelvinator dryer high-limit thermostat 3204267 (overheat protection)

Why it matters

Restricted venting makes drying take much longer and can overheat the dryer. Keeping the lint screen, lint housing, and exhaust duct clean improves drying performance and helps prevent overheating.

Last updated: February 2026

To reset an E64 error on your Frigidaire GLER642AS1 dryer, we recommend doing a power reset: unplug the dryer (or switch off the breaker) for 3 to 5 minutes, then restore power and try a cycle again. If E64 returns, focus on the heating circuit and airflow checks.

Quick reset steps (safe and effective)

• Turn the dryer OFF.
• Unplug the power cord (or turn OFF the dryer breaker).
• Wait 3 to 5 minutes.
• Restore power.
• Close the door and start a cycle (push and hold Start for about 2 seconds on many versions of this dryer).

For control and start procedure details, follow the GLER642AS1 owner's manual.

What E64 usually points to

E64 is commonly tied to an electric-heating problem (often a heater circuit issue). On this model family, the most productive next checks are the basics that cause “drum runs but no heat” symptoms.

Check these first

• House power: Electric dryers typically need two hot legs; if one side is out, the motor can run but heat will not.
• Airflow: A clogged lint screen or restricted vent can overheat the heater housing and trigger safety devices.
• Overheat protection: A tripped thermal limiter can stop heat and requires replacement.

Parts that may be involved (common fixes)

If the dryer tumbles but will not heat after the reset, these model-listed parts are frequent suspects:

Symptom after reset	Most likely area	Example part for GLER642AS1
Tumbles, no heat	Overheat protection opened	Dryer thermal limiter 134120900
Tumbles, weak heat or cycling heat	Temperature control	High-limit thermostat (model-listed)
No start or intermittent start	Start circuit	Start switch (model-listed)

Why it matters

Resetting clears a temporary control glitch, but if E64 comes back it usually means the dryer is protecting itself from a heating or airflow problem. Fixing the root cause helps prevent repeat shutdowns, long dry times, and overheating.

Last updated: February 2026