Kenmore Elite 11095088402 dryer Parts

For Kenmore Elite dryer model 11095088402, the cabinet size is approximately 27 in. wide x 31 1/2 in. deep x 36 in. high. If you add an optional pedestal, total height is about 51 in. (13 in. pedestal) or 53 in. (15.5 in. pedestal). See the 11095088402 owner's manual for the full dimension diagram and clearance notes.

Most installations need extra space beyond the cabinet size for venting, door swing, and service access.

• Width: 27 in. (68.6 cm)
• Depth: 31 1/2 in. (80.0 cm)
• Height: 36 in. (96.6 cm)
• Recommended rear clearance for venting: at least 5 1/2 in. (14 cm) behind the dryer (typical with an elbow)
• Noise reduction tip: about 1 in. (2.5 cm) on each side helps reduce vibration transfer

Correct sizing prevents common install problems like a crushed exhaust duct, a door that cannot open fully, or a dryer that is too tall once a pedestal is added. Planning for clearance also helps airflow, which improves drying performance and helps reduce lint buildup.

Last updated: January 2026

On the Kenmore Elite 11095088402 dryer, CL means Control Locked. When Control Lock is on, the dryer won’t respond to most button presses; you may also see CL alternate with the estimated time remaining.

Use the exact button and hold-time listed in the 11095088402 owner's manual. On most Kenmore Elite dryers, you press and hold the Control Lock button (or the button labeled for Control Lock) for a few seconds until CL turns off.

• Press and hold the Control Lock button (or the button labeled for Control Lock)
• Hold it until the display changes and CL clears
• Try starting a cycle again
• If the panel still won’t respond, unplug the dryer for 1 minute, then restore power and retry

Control Lock is designed to prevent accidental changes to cycle settings (common with kids or bumping the panel).

If Control Lock is on, the dryer can look “broken” even though it’s working normally. Unlocking the controls is the fastest fix before you troubleshoot parts like the drive motor, moisture sensor, or thermistor.

For display-related issues beyond Control Lock, we use the Kenmore elite dryer error codes guide to match the code to the right checks.

Last updated: January 2026

To reset your Kenmore Elite dryer model 11095088402, we recommend a simple power reset: unplug the dryer (or switch off the breaker) for 1 minute, then restore power and start a cycle. If the controls are locked, unlock them using the Control Locked steps in the 11095088402 owner's manual.

• Press PAUSE/CANCEL twice to stop the dryer and clear the current settings.
• Unplug the dryer for 1 minute (or turn the breaker off).
• Restore power.
• Close the door fully.
• Press and hold START for about 3 seconds to begin the cycle.

Your model uses a Control Locked feature to prevent unintended use.

• Press and hold AUTO DRY LEVEL for 3 seconds.
• Confirm the Control Locked indicator turns off.
• Start the cycle again.

A reset clears the control state, but it will not fix airflow or failed parts. If the dryer still will not start or heat, these checks solve most issues:

• Clean the lint screen and confirm strong airflow at the outside vent hood.
• Make sure the door is closing and latching consistently.
• If the drum turns but drying is weak, inspect the blower area; a damaged dryer blower wheel WP697772 can reduce airflow.
• If the dryer runs but heat cuts in and out on a gas model, ignition components can be involved; the dryer valve coil kit 279834 is a common service item.

Resetting correctly prevents unnecessary part replacement and helps you separate a simple control lockout from real problems like restricted venting, a failing blower wheel, or gas ignition issues.

Last updated: January 2026

To change the belt on your Kenmore Elite dryer model 11095088402, we remove the front access components, slip the old belt off the drum and motor pulley, then route the new belt around the drum and through the idler pulley so it maintains proper tension before reassembling the cabinet. Use the 11095088402 owner's manual for model-specific cabinet and access details.

• Unplug the dryer (electric shock protection).
• If you have a gas model, close the gas shutoff valve.
• Pull the dryer forward and avoid crushing or kinking the vent.
• Have a second person help if you need to move the dryer.
• Take photos of wire and panel locations as you disassemble.

1. Remove the lint screen and the screws under the lint screen housing (if equipped).
2. Remove the top panel (usually releases with screws or spring clips at the front).
3. Remove the front panel or front bulkhead (support the drum as you loosen the bulkhead screws).
4. Reach under the drum to release belt tension by pushing the idler pulley toward the motor.
5. Slip the belt off the motor pulley and idler pulley, then lift it off the drum.
6. Install the new belt around the drum with the ribbed side against the drum.
7. Route the belt through the idler pulley and around the motor pulley; rotate the drum by hand to help the belt self-center.
8. Reinstall the bulkhead/front panel, then the top panel, then restore power (and gas, if applicable).

If the dryer squeals, thumps, or the belt failed from wear, we often replace wear items at the same time:

• Dryer idler pulley 279640 (keeps belt tension)
• Support WPW10314173 (drum support roller)
• Dryer repair kit 4392067 (common wear-item bundle for many Whirlpool-built Kenmore dryers)

A correctly routed, properly tensioned belt keeps the drum turning at the right speed. If the idler pulley or drum rollers are worn, a new belt can wear quickly or slip, causing poor drying and noise.

Last updated: January 2026