Owner’s manual
Error Codes
What is the error code SRU?
On the Kenmore Elite dryer model 11095872401, SRU is not a standard dryer error code. When this dryer detects a problem, it typically shows messages like PF (power failure) or E1/E2/E3 service codes; use the troubleshooting section in the owner's manual to confirm what your display is showing.
From the troubleshooting guidance for this Kenmore Elite dryer, these are the code types you should expect:
- PF: the cycle was interrupted by a power failure; press and hold START to restart
- E1 / E2 / E3: service codes that indicate the dryer needs repair
- No code, but poor drying: often points to airflow restriction (lint screen or venting)
Because “SRU” is not a typical code for this model, it is often a misread or partial display. These checks help narrow it down fast:
- Unplug the dryer (or switch off the breaker) for 1 minute, then restore power and see if the message returns
- Look closely for additional letters (for example, E1, E2, E3, or PF) before or after “SRU”
- If the dryer is not heating, confirm the gas shutoff valve is open (gas models)
- Check and clean the lint screen; a damaged screen can also reduce airflow (see screen W10120998)
- If the dryer runs but dries poorly, inspect the vent path for kinks, crushing, or lint buildup
| What you see | What it usually means | What we recommend |
|---|---|---|
| PF | Power interruption | Press and hold START to restart the cycle |
| E1/E2/E3 | Service condition | Stop using the dryer and contact Sears PartsDirect support |
| “SRU” only | Not a normal code for this model | Power reset, then verify the exact characters in the display using the manual |
Using the correct code matters because PF is a simple restart, while E1/E2/E3 points to a repair need. Misreading the display can send you toward the wrong fix and waste time.
Last updated: February 2026
How do I reset a Kenmore dryer?
To reset your Kenmore Elite dryer model 11095872401, we recommend a simple power reset: unplug the dryer (or switch off the breaker) for about 1 minute, then restore power and start a new cycle. This clears many control glitches and restores normal operation.
- Press PAUSE/CANCEL twice to stop the current cycle and clear settings.
- Unplug the dryer for 1 minute (or turn the breaker off).
- Plug back in (or turn breaker on).
- Close the door fully.
- Press and hold START for about 3 seconds to begin the cycle.
- If the dryer was paused, restart within 5 minutes or it may shut off and require reselecting the cycle.
For the exact button behavior on this model, follow the control instructions in the owner's manual.
This model uses a Control Locked feature that can look like the dryer is “stuck.”
- Press and hold AUTO DRY LEVEL for 3 seconds to toggle Control Locked off.
- Try selecting a cycle again.
- Press and hold START for about 3 seconds.
| Action | What it helps | What it will not fix |
|---|---|---|
| PAUSE/CANCEL twice | Clears the current cycle and settings | Broken door switch, failed motor, open thermal fuse |
| Unplug 1 minute | Clears minor electronic glitches | Heating failures caused by bad gas ignition parts |
| Unlock controls | Restores button response | Vent clogs or airflow restrictions |
A reset is the fastest way to clear a stalled cycle or control issue without replacing parts. If the dryer still will not start or run after resetting, the problem is usually a safety interlock (door not sensed closed), a power supply issue, or a failed component in the drive or heating system.
If you are troubleshooting a no-heat condition on a gas model, common repair items for this dryer include the dryer valve coil kit 279834 and the dryer radiant sensor WP338906.
Last updated: February 2026
What does AF stand for on a Kenmore dryer?
On Kenmore Elite dryer model 11095872401, AF means restricted air flow. It indicates the dryer is not moving enough air through the lint screen and exhaust vent, so drying performance can drop and the dryer can run hotter than normal. See the troubleshooting section in the owner's manual.
- Clean the lint screen completely (wash with warm water if it has residue, then dry it).
- Check the outside vent hood for a stuck flap, lint buildup, or blockage.
- Make sure the vent hose behind the dryer is not crushed or kinked.
- Confirm you are using heavy metal or flexible metal venting (not plastic or foil).
- Reduce extra-long vent runs and too many elbows; each turn restricts airflow.
Run the dryer for 5 to 10 minutes, then check airflow at the outside exhaust hood.
| What you feel outside | What it usually means | What to do |
|---|---|---|
| Strong, steady airflow | Venting is likely OK | Recheck lint screen and load size |
| Weak or no airflow | Vent restriction or crushed/kinked vent | Clean/repair the vent path |
| Airflow starts OK then drops | Lint shifting or vent flap sticking | Inspect hood and vent for obstructions |
Restricted airflow is the most common reason clothes take too long to dry. It also increases heat inside the dryer, which can shorten the life of components like the blower wheel and temperature sensors.
If the venting is clear and AF still appears, inspect airflow-related parts. A damaged blower wheel can reduce airflow; for this model, the dryer blower wheel is dryer blower wheel WP697772.
Last updated: February 2026
