Kenmore Elite 59676604600 bottom-mount refrigerator Parts

On Kenmore Elite refrigerator model 59676604600, DH typically indicates a defrost heater (defrost heat) issue. In most cases, it points to a problem in the defrost system that can lead to frost buildup on the evaporator and reduced cooling.

What you’ll usually notice when DH shows up

• Freezer temperature starts rising or swings
• Fresh food section warms up even though the unit runs
• Frost or ice buildup on the rear freezer panel
• Evaporator fan noise changes (or airflow feels weak)
• Water leaking or ice forming from a clogged defrost drain

Quick checks you can do first

Before testing parts, we recommend these safe, practical steps from the 59676604600 owner’s manual:

• Power reset: unplug for 5 minutes, then restore power
• Confirm doors seal fully and close squarely (no gaps)
• Make sure vents are not blocked by food packages
• Set temperatures back to normal if they were changed recently
• Listen for the evaporator fan running when the compressor is on

Parts commonly involved in a DH (defrost) problem

A DH message is usually tied to the defrost heater circuit or temperature sensing. On this model, common suspects include:

• Defrost heater: refrigerator defrost heater WP67002493
• Defrost bi-metal thermostat: refrigerator defrost bi-metal thermostat WP67003426
• Temperature sensor (thermistor): refrigerator thermistor 12002355
• Airflow components (if icing restricts airflow): evaporator fan motor or blade

Defrost system parts at a glance

Part	What it does	Typical failure symptom
Defrost heater	Melts frost off evaporator	Heavy frost, warm fridge
Defrost bi-metal thermostat	Opens/closes heater circuit by temp	Heater never turns on
Thermistor	Reports temperature to control	Erratic temps, defrost timing issues

Why it matters

When the defrost system can’t clear frost, ice can block airflow across the evaporator coil. That reduces cooling performance and can make the refrigerator run longer, warm up, or stop making ice.

Last updated: January 2026

For Kenmore Elite refrigerator model 59676604600, the most reliable way to confirm cubic feet is to look up the capacity in the product specifications section of the 59676604600 owner's manual. If you need a quick estimate, you can calculate interior volume from measurements.

Best way: use the manual specs

Capacity (cubic feet) is a published specification for the refrigerator, not something you can accurately decode from the model number alone.

Use these steps:

• Find the model tag inside the fresh food section (commonly on the left wall).
• Match the full model number exactly: 59676604600.
• Check the specifications or product information section in the 59676604600 owner's manual.

Quick estimate: measure and calculate cubic feet

If you cannot access the spec page right away, you can estimate usable space.

1. Measure the inside of the fresh food compartment (in inches): width, depth, height.
2. Multiply: W x D x H to get cubic inches.
3. Divide by 1728 to convert to cubic feet.
4. Repeat for the freezer compartment and add the two results.

What to measure (for a better estimate)

• Measure to the inside liner, not the door bins
• Subtract obvious “non-space” areas (large air ducts, thick shelves) as needed
• Measure the freezer basket area separately

Model number decoding: what it can and cannot tell you

Kenmore model numbers help identify the manufacturer platform and parts compatibility, but they do not provide a dependable cubic-feet “code.” Some older model families had patterns that loosely correlated with size, but it is not consistent enough to use for ordering parts or comparing models.

Method	Accuracy	Best for
Manual specification	High	Confirming true rated capacity
Interior measurement	Medium	Estimating usable storage space
Model-number guessing	Low	Not recommended

Why it matters

Cubic feet affects how you compare refrigerators, but it does not change most repair part selection. For parts like a temperature sensor, damper, or ice maker, the exact model number match is what ensures correct fit and wiring.

Last updated: January 2026

On Kenmore Elite refrigerator model 59676604600, an ice maker usually stops making ice because it is turned off (sensor arm up), the freezer is not cold enough, or the water supply is restricted. Start by confirming the sensor arm is down and allow up to 24 hours for the first full harvest after changes. See the 59676604600 owner's manual for operating details.

Quick checks that fix most “no ice” problems

• Make sure the ice maker is ON: the sensor arm must be down (arm up turns it off).
• Wait long enough: a full harvest is typically about every 3 hours once conditions are correct.
• If the unit was just installed or water was recently reconnected, expect small/irregular cubes at first due to air in the line.
• Empty and dry the ice bin if cubes are clumping or sticking; clumps can interfere with normal cycling.
• Do not store food or drinks in the ice bin; items can block the sensor arm and cause malfunction.

Water supply and fill problems (common causes)

If the ice maker is on but the mold is not filling with water, focus on the water supply path.

• Confirm the household shutoff valve is fully open.
• Check for a kinked or pinched supply line behind the refrigerator.
• If you recently moved the refrigerator, recheck the connection and watch for slow drips.
• If you suspect a failed valve, the model uses a refrigerator water inlet valve assembly WP67006531 to feed the ice maker.

Temperature and airflow checks

Ice makers need consistent freezer temperatures and airflow.

What you notice	Likely issue	What to do
No ice and freezer feels warm	Freezer not cold enough	Verify settings, keep doors closed, allow 24 hours after adjustments
Ice is hollow or very small	Low water flow or air in line	Purge air by dispensing water (if equipped), check supply line
Ice clumps in bin	Infrequent use or moisture	Empty bin, wash in lukewarm water, dry thoroughly

Why it matters

The ice maker on model 59676604600 is designed to shut off automatically when the bin fills and the sensor arm rises. Anything that blocks the arm, reduces water flow, or prevents proper freezing stops ice production and can also lead to odd cube size and clumping.

Last updated: January 2026

To adjust the height (level) on your Kenmore Elite refrigerator model 59676604600, remove the toe grille, then turn the front and rear adjustment screws to raise or lower the cabinet until it is level side-to-side and slightly higher in front. Follow the steps in the 59676604600 owner's manual.

What you’ll need

• 1/4-in hex head driver (per the manual)
• Carpenter’s level
• Floor protection (cardboard or rugs)

Step-by-step: leveling and height adjustment

1. Remove the toe grille: grasp it firmly and pull outward to unclip it.
2. Adjust the front: use the hex head driver to turn the front adjustment screws (A) on each side to raise or lower the front.
3. Adjust the rear: turn the rear adjustment screws (B) to raise or lower the rear of the refrigerator.
4. Set the correct tilt: check with a carpenter’s level so the front is about 5/16 inch higher than the back (roughly half a bubble), and the cabinet is level side-to-side.
5. Set the stabilizing legs: turn the stabilizing legs (C) clockwise until they are firmly against the floor.
6. Transfer weight to the stabilizers: turn the front adjustment screws (A) counterclockwise until the full weight rests on the stabilizing legs.
7. Reinstall the toe grille: align the mounting clips with the cabinet slots and push until it snaps in.

Quick checks if the refrigerator still rocks or doors won’t self-close

• Confirm the toe grille is fully removed during adjustment (it can interfere with access).
• Re-check side-to-side level; small twists can affect door alignment.
• Make sure stabilizing legs are firmly contacting the floor.
• Verify the floor is solid; soft vinyl or uneven tile can change the final level.

Target leveling specs (easy reference)

What to check	Target for model 59676604600	Why it matters
Side-to-side	Bubble centered	Prevents cabinet twist and door misalignment
Front-to-back	Front about 5/16 in higher than back	Helps doors close and seal properly
Tools	No power tools	Prevents damage to leveling hardware

Why it matters

Proper leveling helps the doors seal correctly, reduces warm air leaks, and can prevent the refrigerator from running too frequently due to poor door closure.

Last updated: January 2026