Kenmore 11027892790 washer Parts

Kenmore washer model numbers are structured so you can identify who built the washer and which design family it belongs to. For Kenmore model 11027892790, the 110 prefix identifies the manufacturer, and the remaining digits narrow down the exact series and feature variations; use the full number when ordering parts.

What each section of a Kenmore model number tells you

Most Kenmore model numbers follow this pattern:

• Prefix (first 3 digits): identifies the manufacturer (for example, 110 is a common Kenmore washer prefix).
• Core model digits (middle group): identifies the base platform or series.
• Trailing digits (last group): identifies feature, color, or production variations.

For parts lookup and compatibility, we always recommend using the entire model number exactly as shown on the model and serial plate.

Where to find the model number on your washer

On Kenmore washers like 11027892790, the model and serial information is printed on the model and serial number plate. The owner's manual also calls out this plate and recommends recording the full model and serial numbers for future reference.

• Check the cabinet area around the lid opening (top-load washers commonly place it there).
• Look for a printed plate or label that lists Model No. and Serial No.
• Write the full model number down before shopping for parts.

Why the full model number matters for parts

Even small digit changes can mean different components (agitator parts, drive system parts, or water valve styles). Using the full model number helps match the correct replacement part the first time.

What you’re doing	What to use	Why it helps
Ordering replacement parts	Full model number (all digits)	Ensures correct fit and compatibility
Checking operating details	Manual for your exact model	Confirms cycle features and usage guidance
Scheduling a repair or troubleshooting	Model and serial number	Identifies the correct design and production run

Quick example using this model

• Model: 11027892790
• Manufacturer prefix: 110
• Variation digits: 27892790

Last updated: February 2026

To unclog the drain hose on your Kenmore washer model 11027892790, unplug the washer, remove as much water as possible, then disconnect and flush the drain hose and check the drain pump inlet for debris. Reinstall the hose exactly as shown in the owner's manual.

Before you start (safety and spill control)

• Unplug the power cord.
• Turn off both water supply valves.
• Bail out the tub or wet-vac the water from the tub if it will not drain.
• Keep towels and a shallow pan ready; the hose and pump will release water.
• If the washer is full of water, avoid tipping it; pull it forward carefully.

How we unclog the drain hose (step-by-step)

1. Check for kinks first: Straighten the hose behind the washer and at the standpipe or laundry tub.
2. Remove the hose from the standpipe/tub: Look for lint, coins, socks, or a crushed hose end.
3. Flush the hose: Run hot tap water through it (a garden hose works well). If it is packed with lint, push a small drain snake through from the standpipe end.
4. Check the pump inlet: If the hose is clear but the washer still will not drain, disconnect the hose at the washer and inspect the pump inlet for debris.
5. Reinstall correctly: Wet the inside of the straight hose end with tap water only, clamp it in the correct position, and push the hose fully onto the drain connector until it hits the stop.

Quick diagnosis guide

Symptom	Most likely cause	What to do next
Hums but will not drain	Pump jam or blockage at pump inlet	Inspect pump inlet; consider replacing the washer drain pump WP3363394
Drains slowly	Lint buildup in hose or standpipe restriction	Flush hose; clear standpipe; avoid sealing hose into standpipe
Won’t drain and hose is kinked	Hose routing issue	Reroute hose; keep a smooth curve with no pinches
Water backs up or siphons	Hose shoved too far into standpipe, no air gap	Keep a loose fit; do not tape/seal the hose

Why it matters

A partially clogged drain hose can cause “won’t drain/wet loads,” longer cycle times, and pump damage. Correct hose routing and clamping also helps prevent leaks and floor damage.

Last updated: February 2026

A Kenmore washer typically lasts 10 to 15 years. For your Kenmore 11027892790 top-load washer, consistent maintenance (proper loading, correct detergent, and periodic cleaning) helps you reach the high end of that range and reduces wear on the drive and drain systems.

What affects washer lifespan most

• Load size and balance: chronic overloading strains the clutch, gear case, and suspension.
• Water quality: hard water speeds up residue buildup and can affect valves and seals.
• Drain performance: slow draining makes the pump work harder and can leave standing water.
• Agitation and spin wear: worn agitator components can reduce cleaning and increase stress on the drivetrain.
• Routine care: cleaning residue and using the right amount of detergent prevents odors and buildup.

Typical lifespan by component (what usually fails first)

Component area	Common symptom	Example part for this model
Agitation	Agitator slips or does not “ratchet”	Agitator dog 80040
Coupling/drive	Motor runs but tub does not agitate/spin	Coupling 285753A
Draining	Won’t drain, hums, or drains slowly	Washer drain pump WP3363394
Spin engagement	Weak spin, burning smell, noisy spin	Clutch 285785

Maintenance that extends life (practical checklist)

• Keep loads evenly distributed; wash bulky items with similar items.
• Use HE detergent in the correct amount (too much causes residue and odors).
• Check fill and drain behavior; address slow draining early.
• If agitation is weak, inspect common wear items like the agitator dog 80040.
• Follow the cleaning and care guidance in the owner's manual.

Why it matters

A washer that is maintained well not only lasts longer, it also cleans better and avoids secondary damage (for example, a draining issue can lead to odors, standing water, and extra strain on the pump and drive system).

Last updated: February 2026

Kenmore washer model 11027892790 is a classic agitator top-load design; washers in this design class typically run about 3.2 to 3.8 cubic feet. For the most accurate capacity for your exact unit, use the basket-measurement method in the 11027892790 owner's manual.

Best way to get the exact cubic feet (works for any washer)

Measure the inside of the wash basket (not the outer tub), then calculate volume.

• Measure inside diameter (inches)
• Measure inside depth to the rim (inches)
• Convert to feet (divide inches by 12)
• Use: Volume (cu. ft.) = π × (radius in feet)² × (depth in feet)

Quick reference table

What to measure	Where	Tip
Diameter	Inside wall to inside wall	Measure across the widest point
Depth	Basket bottom to top rim	Do not include the console or lid
Radius	Diameter ÷ 2	Convert to feet before squaring

What capacity range to expect for this Kenmore style

These ranges help you sanity-check your calculation.

• Standard agitator top-load: 2.9 to 3.5 cu. ft.
• “Super capacity” agitator top-load: 3.2 to 3.8 cu. ft.
• High-capacity impeller top-load: 4.0 to 5.5+ cu. ft.

Why it matters

Capacity affects load size, cleaning action, and spin balance. Overloading increases strain on drive components such as the clutch 285785 and can contribute to vibration, poor rinsing, and wear.

Last updated: February 2026