Kenmore 66513003N510 dishwasher Parts

To identify your Kenmore dishwasher model, we look for the model and serial tag on the tub or door area. On Kenmore models like 66513003N510, it’s most often visible when you open the door and check the inner door frame, the top edge of the door, or the tub wall. Use the exact model number to match parts and instructions in the 66513003N510 owner's manual.

Where to find the model number tag

Check these common locations in this order:

• Inside the door opening on the left or right inner frame
• Along the top edge of the door (visible with the door open)
• On the tub wall near the door latch area
• Behind the lower access panel (kickplate) area
• On the side of the dishwasher frame (visible when the unit is pulled out)

What the model number looks like (Kenmore)

Kenmore dishwasher model numbers often start with 665 (a common Kenmore prefix). Your full model number will be a longer string, such as 66513003N510.

What you see	What it means	What to do with it
665xxxxx…	Kenmore dishwasher model prefix	Use the full number for parts lookup
Serial number	Unique unit identifier	Helpful for service history and age
Partial digits only	Incomplete ID	Keep looking for the full tag

Why it matters for parts and troubleshooting

We use the exact model number to ensure the part fits your specific Kenmore dishwasher configuration (controls, racks, pump system, and wiring). Even small model variations can change which items fit, such as a dishwasher water inlet valve W11175771 or dishwasher drain pump W10876537.

Quick tips if the tag is hard to read

• Wipe the label gently with a damp cloth and mild soap, then dry it
• Use your phone camera and zoom in (flash helps)
• Copy the model number exactly, including letters and ending digits
• If the label is damaged, check your purchase paperwork or the installation guide for model identification references

Last updated: February 2026

Common problems with Kenmore dishwashers like model 66513003N510 include not starting, not filling, not draining, poor cleaning, and water not heating. Many issues trace back to power, the door not latching, water supply being off, or a clogged filter or drain path; our installation guide includes quick checks for “does not operate.”

Most common symptoms and what they usually mean

• Won’t start: tripped breaker, blown fuse, door not fully latched, cycle not set to start
• No water or low fill: water supply valve off, restricted supply, inlet valve problem
• Won’t drain: kinked/clogged drain hose, blocked filter area, drain pump issue
• Dishes still dirty: clogged filter, blocked spray arm holes, loading or detergent issues
• Water not heating or long cycles: heater or thermostat issue, or normal longer cycles due to soak pauses

Quick checks we recommend first (fast, no parts)

These checks match the “If Dishwasher Does Not Operate” guidance used during setup and testing:

• Reset the circuit breaker or replace the house fuse if needed
• Confirm the door closes tightly and latches
• Make sure the cycle is selected correctly and started
• Verify the water supply is turned on under the sink
• Run a short cycle and check for water in the bottom of the tub after about 2 minutes (then close the door and let it continue)

Parts that commonly fix these problems (when checks don’t)

Symptom	Common part area	Example part for 66513003N510
Not draining	Drain system	Dishwasher drain pump W10876537
Not filling	Water inlet	Dishwasher water inlet valve W11175771
Poor cleaning	Wash action/filtration	Dishwasher spray arm WPW10491331, dishwasher filter WPW10463906
Not heating/drying well	Heating circuit	Element assembly W10518394

Why it matters

Dishwashers are designed to clean with spray action plus soak pauses; when water can’t enter, circulate, heat, or drain correctly, you will see longer cycles, dirty dishes, standing water, or a unit that won’t run at all.

Last updated: February 2026

To hard reset your Kenmore dishwasher model 66513003N510, we recommend canceling the current cycle and then power-cycling the dishwasher (turn power off at the breaker for about 1 minute, then restore power). After power is back on, start a fresh cycle using the steps in the owner's manual.

Quick reset options (most common)

• Cancel/Drain reset: Press Cancel/Drain (or Cancel) and let the dishwasher pump out.
• Breaker reset: Turn the dishwasher circuit OFF at the home breaker for 1 minute, then turn it back ON.
• Control lock check: If the controls seem unresponsive, make sure Control Lock is not enabled.
• Door reset: Close the door fully and latch it; many Kenmore units will not respond if the latch is not engaged.

What a “hard reset” actually fixes

A hard reset clears many temporary control issues such as a frozen keypad, a stuck cycle, or a cycle that will not start after a power flicker. It does not fix mechanical problems like a drain restriction, a failed heater, or a water fill issue.

If it still will not run after resetting

Check these items in order:

• Power: Confirm the breaker is on and the dishwasher has power.
• Water supply: Verify the shutoff valve under the sink is open.
• Drain path: Make sure the drain hose is not kinked and the sink/disposer drain is clear.
• Overfill protection: If the dishwasher acts like it is “stuck,” the float system can be involved; see dishwasher float switch WPW10195039.
• Fill problems: If it hums but will not fill, the inlet valve can be a suspect; see dishwasher water inlet valve W11175771.

Helpful guide for flashing lights or codes

If your dishwasher is showing a pattern of blinking lights or an error code, use the Kenmore 665 model dishwasher error codes guide to match the symptom to the most likely cause.

Common symptoms and what they point to

Symptom after reset	Most likely area to check	Example part on this model
Won’t fill with water	Water supply, inlet valve	W11175771
Won’t drain	Drain path, drain pump	W10876537
Washes poorly	Spray arm, filters	WPW10491331, WPW10463906

Why it matters

Resetting is a fast way to restore normal operation after a control glitch, and it helps you separate a one-time electronic issue from a repeatable problem that needs troubleshooting or a replacement part.

Last updated: February 2026

If the Start/Resume button on your Kenmore 66513003N510 dishwasher won’t start a cycle, the most common cause is the door not latching or not being closed quickly enough after pressing Start. This model can flash the Start/Resume light if the door is not closed within 3 seconds.

Quick checks that fix most “won’t start” issues

• Make sure the door is fully closed and latched; push firmly at the latch area.
• Press Start/Resume, then close the door within 3 seconds (or the Start/Resume light can keep flashing).
• Verify power: check the house breaker or fuse, then confirm the dishwasher has power.
• Confirm a cycle is actually selected (some models will not start if no cycle is chosen).
• Make sure the water supply valve under the sink is turned on.

For model-specific operating details, follow the steps in the 66513003N510 installation guide.

What to check next (if the button still does nothing)

If the dishwasher has power but will not begin a wash cycle, we focus on the “start permission” items first (door switch, control, and wiring), then move to fill and drain components.

• Door latch and door switch: if the latch is loose or the switch is not closing, the control will not start the motor.
• Control panel or electronic control: a failed key switch or control can prevent Start/Resume from registering.
• Wiring connections: look for loose connectors at the control and door area.
• Flood protection/overfill: if the unit thinks it is overfilled, it may refuse to run.

Parts that commonly relate to start or fill problems

These parts are on the parts list for Kenmore 66513003N510 and are often involved when a dishwasher will not start or will not fill correctly:

Symptom you notice	What it often points to	Example part on this model
Start/Resume flashes, won’t run	Door not latched in time, door switch issue	Use the owner's manual for the exact start sequence
Hums but won’t fill	Water supply issue, inlet valve problem	Dishwasher water inlet valve W11175771
Won’t drain, cycle won’t continue	Drain restriction or drain pump issue	Dishwasher drain pump W10876537

Why it matters

Your dishwasher’s control will only start a cycle when it “sees” a safe condition: power is present, a cycle is selected, and the door is closed and latched. If any of those signals are missing, the Start/Resume button can appear to not work even though the lights come on.

Last updated: February 2026