Maytag MDG6800AWW dryer Parts

The Maytag MDG6800AWW is an oversized, full-size 27-inch dryer; models in this Maytag Neptune-style platform are typically around 6.0 cu. ft. capacity. For the exact rated capacity for your specific unit, confirm it in the MDG6800AWW owner's manual.

How to confirm the exact capacity on your dryer

We recommend verifying capacity using the model identification and specifications information tied to your exact unit.

• Check the model and serial tag in the lower center of the door opening.
• Match the model number exactly: MDG6800AWW.
• Look for “capacity” or “drum volume” in the specifications section.
• If your manual lists multiple variants, use the section that matches your fuel type (gas) and control style.
• Keep the manual with your purchase information for future reference.

Typical capacity range (what to expect)

Most 27-inch Maytag full-size dryers from this era fall into a narrow capacity range.

Dryer size class	Common width	Typical capacity range
Compact	24 in.	3.4 to 4.0 cu. ft.
Full-size	27 in.	5.8 to 7.4 cu. ft.
Oversized full-size	27 in.	6.0 to 7.4 cu. ft.

Why it matters

Capacity affects load size, drying time, and efficiency. Using the right load size helps the dryer tumble properly, improves airflow through the lint filter, and reduces wear on drive components such as the dryer drum belt WP33002535.

Last updated: February 2026

On a Maytag MDG6800AWW dryer, we find the model number on the appliance’s rating label; it is typically located around the door opening (door jamb) or just inside the front panel area. Use the MDG6800AWW installation guide to confirm the exact label location for your setup.

Where to look on the dryer

• Open the dryer door and check the door jamb (the frame the door closes against).
• Look along the front opening near the lint screen housing.
• Check the rear panel label if you do not see it at the door.
• If the label is worn, use a bright light and take a close-up photo to read it.

What you should write down

• Model number: MDG6800AWW
• Serial number: unique to your dryer (helps confirm production run)
• Type: gas dryer (this model uses gas ignition components)

Why the exact model number matters

The model number ensures we match the correct Maytag drum-drive and gas-heat parts, such as the belt, igniter, and lint filter. Even small model variations can change fit and wiring.

Quick ID checklist

Item	Example	Used for
Model number	MDG6800AWW	Correct diagrams and parts match
Serial number	Varies	Version-specific compatibility
Part number	Example: 33002535	Manufacturer identifier on parts

Last updated: March 2026

For your Maytag MDG6800AWW dryer, we troubleshoot by matching the symptom (no heat, no start, long dry times, noise) to the most likely airflow, ignition, or drum-drive cause; then we confirm with a few quick checks and targeted part tests using the MDG6800AWW owner's manual.

Quick safety first

• Unplug the dryer before opening panels.
• For gas models, shut off the gas supply valve before servicing.
• If you smell gas: stop, ventilate the area, and do not operate the dryer.

Symptom-based checks (most common)

• Dryer will not start: confirm power, door fully closed, and cycle selected; then suspect a drive issue such as a worn belt.
• Runs but no heat: check airflow first; then suspect ignition components.
• Takes too long to dry: almost always restricted venting or a clogged lint path.
• Squealing, thumping, or rumbling: usually drum support or idler components.

Parts that commonly fix these symptoms

Symptom	Common cause	Example part for MDG6800AWW
Won’t tumble, motor runs	Broken belt	Dryer drum belt WP33002535
No heat (gas)	Ignition failure	Dryer burner igniter WP33002789
No heat (gas) or short cycling	Flame sensing issue	Gas sensor WP338906
Loud rumble or thump	Worn drum support	Whirlpool dryer drum support roller 12001541
Poor drying	Lint restriction	Dryer lint filter WP33001808

Step-by-step: long dry time (highest payoff)

• Clean the lint screen and confirm it is not torn or warped.
• Inspect the vent hose for kinks, crushing, or excessive length.
• Check the outside vent hood for a stuck flap or lint blockage.
• Run a timed dry cycle and verify strong airflow at the outlet.

Why it matters

Good airflow protects the heater and gas burner system, prevents overheating, and cuts dry times. Fixing vent restrictions first also prevents replacing parts that are not actually bad.

Last updated: March 2026