Kenmore 11060842990 electric dryer Parts

Replacing the heating element in your Kenmore electric dryer model 11060842990 typically costs $50 to $120 for the part plus $100 to $250 for labor if you hire service, so most total repairs land around $150 to $350. For this model, the heating element we list is dryer element 279838.

• Heating element part: usually $50 to $120 (model-specific)
• Service call and labor: commonly $100 to $250
• Optional related parts (sometimes needed): thermal cut-off, thermostat, wiring repair kit
• DIY cost: usually just the part (and any related safety parts)

If your dryer runs but does not heat, we often see airflow or safety-limit issues that can take out the heater circuit. Before replacing parts, we recommend checking these common causes:

• Clogged lint screen or restricted venting (overheats the heater housing)
• Blown thermal cut-off or failed high-limit thermostat
• Loose or burned heater wire connections
• Timer or cycling thermostat issues (less common)

For model-specific operating and care guidance, use the 11060842990 owner's manual.

A restricted vent can overheat the heater area and repeatedly trip safety devices, which can make a new heating element fail early. Keeping airflow strong helps drying performance, energy use, and part life.

• Cut-off kit 279816 (thermal cut-off kit)
• Dryer thermostat WP3977767 (high-limit thermostat)
• Dryer heating element wire kit 279457 (repair kit for damaged heater wiring)

If you are ordering parts, you can buy the model-specific parts listed for 11060842990 from the parts list, or search by model on Sears PartsDirect.

Last updated: February 2026

For a Kenmore electric dryer like model 11060842990, the most reliable “reset” is a power reset: turn the dryer off, unplug it (or switch the breaker off) for 1 minute, then restore power and start a cycle normally. For model-specific operating steps, use the 11060842990 owner's manual.

• Turn the Cycle selector (timer) to OFF.
• Unplug the dryer or turn both dryer breakers off.
• Wait 1 minute.
• Restore power.
• Close the door fully.
• Select a dry cycle and press PUSH TO START.

These checks solve most “dead” or “won’t start” complaints on this style of Kenmore dryer:

• Confirm the door is fully closed and the latch catches; a worn latch can prevent starting.
• Make sure the timer is set to a dry setting (not between positions).
• Verify the outlet has full power (electric dryers typically need 240V; a tripped breaker can leave partial power).
• If the dryer runs but stops when you open the door and will not restart, close the door and press PUSH TO START again.
• If the button does nothing, the start switch can be the issue; see dryer push-to-start switch WP3395382.

A power reset clears minor control glitches and restores normal operation after a power interruption. It will not fix a failed component such as a bad start switch, door latch, timer, or motor.

Repeated “resets” can hide an underlying electrical or mechanical problem. Fixing the root cause helps prevent no-start situations and reduces wear on the motor and timer.

You can order replacement parts for model 11060842990 from the parts list for this dryer, or search by model number on Sears PartsDirect.

Last updated: February 2026

On the Kenmore 11060842990 electric dryer, the thermal fuse is a small, flat safety device mounted on the blower housing or heater housing; most dryer thermal fuses are roughly 1 to 2 inches long with two wire terminals. For the exact location and access steps, use the 11060842990 owner's manual.

Thermal fuses are commonly described by function and mounting style, not just physical dimensions. When you shop or troubleshoot, focus on:

• Mounting: typically 2 screws through a flat plastic or metal body
• Terminals: usually 2 spade terminals (one wire on each)
• Form factor: slim, rectangular, easy to hold between two fingers
• Trip behavior: opens the circuit if the dryer overheats

A blown thermal fuse often causes a no-start condition (the motor circuit is interrupted). Before replacing parts, we recommend these checks:

• Confirm the dryer door closes and latches properly
• Verify the outlet has full power (electric dryers can run but not heat if one supply leg is lost)
• Clean the lint screen and check airflow at the outside vent hood
• Inspect the vent for crushing, kinks, or heavy lint buildup
• If the dryer overheated, correct the airflow restriction first so the new fuse does not blow again

Restricted airflow is the most common reason a thermal fuse opens. These model-compatible parts can help address root causes:

The thermal fuse is a one-time safety cutoff. Replacing it without fixing the overheating cause (usually venting or lint buildup) leads to repeat failures and poor drying performance.

If you need to order model-correct replacement parts, use the parts list for Kenmore 11060842990 or search by model on Sears PartsDirect.

Last updated: February 2026