Installation guide
Owner’s manual
Error Codes
How to reset Kenmore oven model 79096113408?
To reset the Kenmore electric range model 79096113408, turn the range OFF, then restore power by cycling the breaker (or unplugging and plugging back in). After power returns, reset the clock and any oven settings as described in the 79096113408 owner's manual.
Quick reset steps (most common)
- Turn all surface element knobs to OFF.
- If the oven is running, press Cancel/Off.
- Turn OFF the range circuit breaker for 1 minute.
- Turn the breaker ON.
- Set the clock and re-enter any cooking functions.
If the control is locked (LOC shows on the display)
This model has an oven lockout feature that can look like a “stuck” control.
- Press and hold the Oven Lockout pad for 3 seconds.
- Wait about 15 seconds for the door lock motor to finish.
- To cancel lockout, press and hold the same pad for 3 seconds again.
What a reset fixes vs. what it does not
| Symptom | Reset may help | More likely cause |
|---|---|---|
| Display frozen or unresponsive | Yes | Control glitch after a power event |
| Oven functions stop after outage | Yes | Clock and settings need reprogramming |
| Burner stays on high/low incorrectly | Sometimes | Failed infinite switch such as range surface element control switch 316436001 |
| Error code keeps returning | Sometimes | Sensor, wiring, or control issue |
Why it matters
A power interruption can leave the electronic oven control in an unstable state. Resetting power clears the control memory, and setting the clock restores normal timed functions and baking features.
Last updated: January 2026
How do I tell what model Kenmore stove I have?
For Kenmore ranges, the model number is printed on the appliance’s identification plate. On Kenmore model 79096113408, that plate is located on the right side of the oven front frame inside the storage or warmer drawer compartment; pull the bottom drawer out and look along the right-side frame. See the 79096113408 owner's manual for the exact label location diagram.
Where to look on the range
Check these common spots in this order:
- Inside the storage drawer or warmer drawer opening, on the right-side front frame
- Along the oven door frame (door jamb area) when the door is open
- On the back of the range near the upper vent area or backguard
- Under the cooktop edge (less common, but possible on some designs)
What the model number looks like (and why it matters)
Kenmore range model numbers are typically a long number string. For this family, you may see a prefix like 790. on the label, followed by additional digits.
| What to record | Example format | Why you need it |
|---|---|---|
| Model number | 79096113408 (or 790.xxxxxxxx) | Ensures parts fit and diagrams match |
| Serial number | Letters and numbers | Helps date the unit and confirm revisions |
| Purchase date (optional) | Month/year | Useful for service history |
Tips for reading the label
- Use a flashlight; the plate is often metallic and reflective.
- Wipe dust and grease gently with a damp cloth so the digits are readable.
- Take a clear photo of the full label before ordering parts like a surface element switch or bake element.
Why it matters
The model number ties your range to the correct parts list, wiring layout, and troubleshooting steps. Even small model variations can use different control switches, surface elements, or oven components.
Last updated: January 2026
What is the width of a Kenmore range?
Most Kenmore ranges are 30 inches wide, and the Kenmore electric range 79096113408 is designed for a 30-inch opening; the installation dimensions show an overall width of about 29 7/8 inches (with a cooktop width called out around 30 1/8 inches). See the 79096113408 installation guide for the exact diagram.
Model-specific width for Kenmore 79096113408
The installation guide provides the key measurements used for cabinet and countertop planning.
- Overall range width: about 29 7/8 in.
- Cooktop width callout: about 30 1/8 in.
- Standard opening target: 30 in. (common for freestanding electric ranges)
Quick reference table
| Measurement type | What it means | Typical value for 79096113408 |
|---|---|---|
| Overall width | Body width that fits between cabinets | ~29 7/8 in. |
| Cooktop width callout | Top surface dimension shown in the diagram | ~30 1/8 in. |
| Cabinet opening | Space you plan in the cutout | 30 in. |
How to measure your range correctly
Use a tape measure and check more than one spot; trim pieces and the cooktop can be slightly wider than the body.
- Measure the widest point across the cooktop (left edge to right edge).
- Measure the body width below the cooktop (side panel to side panel).
- Confirm the cabinet opening width between the base cabinets.
- Account for side clearances and any countertop lip that could interfere.
Why it matters
Range width affects fit, safe clearances, and whether the cooktop sits properly on the countertop. Using the installation dimensions helps prevent cabinet cuts that are too tight and avoids heat-related clearance issues.
Last updated: January 2026
How to lift a Kenmore stove top?
On the Kenmore 79096113408 electric range, the cooktop typically lifts after you remove any items sitting on it and release the front hold-down points (clips or screws, depending on configuration). Use the steps in the 79096113408 installation guide for safe access and stability checks before you work around wiring.
Before you start (safety and setup)
- Turn off power at the breaker; an electric range can still have live voltage at the terminal block.
- Let the cooktop fully cool; radiant elements and glass stay hot longer than they look.
- Pull the range forward carefully; avoid stressing the power cord.
- Confirm the anti-tip bracket is engaged before and after moving the range.
- Protect the floor with cardboard or a thin plywood sheet.
How to lift the cooktop (common Kenmore electric range method)
- Remove everything from the cooktop surface.
- Open the oven door and look under the front edge of the cooktop for hold-down screws or spring clips.
- If screws are present, remove them; if clips are present, release them with a flat-blade screwdriver.
- Lift the front of the cooktop slowly.
- Support the cooktop with a sturdy prop (wood block) so you do not strain wiring.
What you may need to remove first
| Cooktop style | What usually comes off first | Notes |
|---|---|---|
| Radiant glass cooktop | Nothing on top; access is from the front/under edge | Lift gently to avoid cracking glass |
| Coil element cooktop | Elements and drip pans (if equipped) | Some models also use mounting screws |
Why it matters
Lifting the cooktop is the first step for diagnosing common issues like a burner not heating, a hot surface light staying on, or a loose wire at a surface element switch. Correctly supporting the top prevents broken glass, pinched harnesses, and damaged element terminals.
Related troubleshooting help
If you are lifting the top because a burner is not working, follow the checks in radiant surface element on range not working video before replacing parts.
Last updated: January 2026
