Kenmore 11079622800 dryer Parts

Yes. We carry replacement parts for Kenmore dryers, including the Kenmore model 11079622800, so you can fix common wear items (belts, switches, thermostats) and restore safe, reliable drying. Use the 11079622800 owner's manual to confirm symptoms and maintenance steps before ordering.

These are some of the most frequently replaced parts for model 11079622800:

• Dryer drum belt 341241 when the drum will not turn or you hear a slipping squeal
• Door switch (if the dryer will not start when the door is closed)
• Operating thermostat (for overheating or poor temperature control)
• Thermal cut-off kit (after an overheat event)
• Igniter, radiant sensor, or gas valve coils (for a gas dryer that tumbles but will not heat)

Start with your full model number and then match by symptom and location.

• Confirm the model tag reads 11079622800
• Compare the part name and ID to what you are replacing
• Check whether your dryer is gas or electric before ordering heat-related parts
• Inspect for lint buildup and vent restrictions first (they can cause overheating and repeat failures)

Dryer parts wear out normally (belts, light bulbs, and other expendable items), and restricted venting can shorten the life of heating and safety components. The manual also calls out routine care like cleaning the lint screen and keeping the exhaust area clear to help prevent performance problems.

Last updated: February 2026

Your Kenmore dryer’s model number is printed on the model and serial number label (rating plate). On Kenmore model 11079622800, you’ll typically find that label in the door opening (door well) or on the cabinet, and it lists both the model and serial number.

Check these common locations first (use a flashlight and wipe dust off the label):

• Inside the dryer door opening on the cabinet frame (door well)
• Along the front panel just inside the door
• On the back of the dryer cabinet near the top edge
• On the side panel near the rear (less common)

We recommend recording the full model number and serial number exactly as shown on the label. The manual also calls out keeping this information handy for faster service and correct parts lookup.

• Copy every digit; don’t shorten the number (for example, use 11079622800, not “110.7962”).
• If the label is worn, take a clear photo and zoom in.
• If your dryer is gas, the rating plate can also list burner and gas information used for installation checks.

Kenmore dryers share many similar-looking parts across model families. Using the exact model number helps us match the correct diagrams and parts, such as the dryer drum belt 341241 or the dryer door switch WP3406107, and prevents ordering the wrong replacement.

For label location details and how the information is used, see the 11079622800 owner's manual.

Last updated: February 2026

For a Kenmore dryer model 11079622800, replacing a temperature-sensing part typically costs $20 to $60 for the part, plus $100 to $250 for labor if you hire service; total installed cost is commonly $120 to $310. Confirm the exact sensor type and access steps in the 11079622800 owner's manual.

• Which “temperature sensor” it is: operating thermostat, high-limit thermostat, thermistor, or radiant sensor (gas models)
• Service call minimum: many companies charge a flat diagnostic fee that applies even if you decline repair
• Vent restriction: overheating from poor airflow can damage sensors and fuses, increasing parts and labor
• Stacked repairs: techs often recommend replacing related wear items while the dryer is open

• Check your symptom: no heat, overheats, shuts off early, or won’t start after overheating
• Use the wiring diagram and component locations in the 11079622800 installation guide to plan access and reassembly
• If your dryer is gas and heat is intermittent, consider the dryer radiant sensor WP338906 as a common temperature-related suspect
• If the dryer runs but heat cycles oddly, the dryer operating thermostat WP3387134 is a frequent replacement item

A failed temperature-sensing component can cause long dry times, overheating, or repeated safety shutoffs. Fixing airflow issues (lint screen, duct, outside hood) at the same time helps the new sensor last and keeps drying performance consistent.

Last updated: February 2026

A hard reset for your Kenmore dryer model 11079622800 is a power reset: unplug the dryer (or switch the breaker off) for about 1 minute, then restore power and restart the cycle. If it still will not start, confirm the door is fully closed and power is reaching the outlet.

• Turn the Cycle Selector to Off.
• Unplug the dryer (or turn the circuit breaker off).
• Wait 60 seconds.
• Restore power.
• Close the door, select a cycle, then press PUSH TO START (as described in the 11079622800 owner's manual).

Use this quick checklist from the installation and use instructions:

• Verify the dryer is plugged into a grounded 3-prong outlet (no adapter, no extension cord).
• Confirm the household fuse is intact or the circuit breaker has not tripped.
• Make sure the dryer door is closed.
• Try a Timed Dry heated cycle (not an air-only setting) to confirm basic operation.
• For gas models, confirm the gas shutoff valve is open.

If the dryer only runs when you press on the door, or it stops when the door is bumped, the door switch circuit is a common failure point.

• Dryer door switch WP3406107
• Door strike and latch alignment (inspect for looseness or wear)
• Start switch and timer contacts (if equipped)

A reset clears a temporary control “hang” and forces a clean restart, but it will not bypass safety circuits. If power, door closure, or (on gas models) the gas supply is not correct, the dryer can appear “dead” even after a reset.

Last updated: February 2026

On Kenmore dryer model 11079622800, opening the control panel typically means removing the top panel first, then removing the screws that secure the control console so it can hinge forward or lift off for access to the timer or electronic control board. Use the steps in the 11079622800 installation guide for safe access and handling.

• Unplug the dryer (or switch off the breaker) before removing any panels.
• If this is a gas dryer, close the gas shutoff valve before servicing.
• Pull the dryer forward enough to work without crushing or kinking the vent.
• Keep screws organized by location (top, console, brackets).
• Protect the finish by placing a towel on top when lifting panels.

1. Disconnect power and confirm the drum light and controls are off.
2. Remove the top panel: release the top (usually from the back screws or spring clips), then lift up and slide it back slightly to remove.
3. Locate the console mounting screws (often 1/4-in hex-head screws) and remove them.
4. Tilt the control panel forward carefully; support it so wiring is not strained.
5. If you need deeper access, label and disconnect wire connectors, then remove the console bracket.

If the dryer will not start after reassembly, the door switch is a common failure point; the dryer door switch WP3406107 is the correct switch listed for this model.

Opening the control panel the right way prevents broken console tabs, pinched wiring, and reassembly issues that can cause a no-start condition or intermittent operation.

Last updated: February 2026

A Kenmore dryer typically lasts 10 to 13 years. With consistent care (especially lint and vent cleaning), many Kenmore dryers run 15 years or more; poor airflow and heavy use shorten life. For model 11079622800, follow the maintenance guidance in the 11079622800 owner's manual.

Most dryers wear out from heat stress, restricted airflow, and normal drum support wear.

• Longer life: clean venting, correct load sizes, stable power/gas supply
• Shorter life: clogged venting, frequent overheating, running overloaded cycles
• Usage matters: multiple loads daily ages a dryer faster than light weekly use
• Environment matters: very cold rooms can affect operation (cycles work best above about 45°F)

These steps reduce overheating and strain on the motor, belt, and thermostats.

• Clean the lint screen every load
• Check and clean the exhaust duct and outside hood regularly (at least yearly)
• Keep the dryer level so the drum and rollers wear evenly
• Avoid overloading; it stretches the belt and stresses the drive system
• Stop using the dryer if you smell burning or notice repeated overheating

If your 11079622800 is squealing or not tumbling, the dryer drum belt 341241 and related drum support parts are common service items.

A dryer that is near end-of-life often costs more to run and is harder on clothing because it needs longer cycles. Keeping airflow strong is the single best way to protect the heater, thermostats, motor, and drum drive.

Last updated: February 2026

For Kenmore dryer model 11079622800, the overall size is approximately 43 3/8 inches high, 27 inches wide, and 29 inches deep (depth varies slightly by door style). For installation, plan on at least 5 inches of clearance behind the dryer for the exhaust vent elbow; see the 11079622800 installation guide.

These measurements come from the installation dimensions section and are the best numbers to use for fit checks.

• Width: 27 in (705 mm)
• Height: 43 3/8 in (1102 mm)
• Depth: about 29 in (737 mm), depending on door configuration
• Behind-dryer clearance: minimum 5 in (127 mm) typically needed for venting with an elbow
• Closet installs: door must allow the dryer door to open fully; ventilation openings are required

Correct sizing prevents crushed venting, poor airflow, longer dry times, and overheating. The extra rear clearance is especially important on vented Kenmore dryers because the exhaust elbow needs room to route without kinking.

• Measure the tightest point (door jambs, trim, baseboards).
• Include space for the gas line and shutoff valve if this is a gas installation.
• If installing in a closet, confirm top and bottom door vent openings meet the guide’s requirements.
• If you plan to service the dryer later, leave extra side clearance for easier access.

Last updated: February 2026