Kenmore Elite 66513979K015 undercounter dishwasher Parts

To take your Kenmore Elite dishwasher model 66513979K015 out of lock mode, press and hold CONTROL LOCK for 3 seconds until the LOCK ON light turns off. The door can still open and close while locked, but the dishwasher will not run.

Quick unlock steps

• Press and hold CONTROL LOCK for 3 seconds.
• Watch for LOCK ON to turn off.
• If you press other buttons while locked, the lock light typically flashes 3 times and you may hear a tone.
• After unlocking, reselect your cycle and press START/RESUME.
• If you opened the door during a delay start, press START/RESUME again to continue the countdown.

What to check if it will not unlock

• Make sure you are pressing the correct pad labeled CONTROL LOCK (some models use a dedicated button).
• Press and hold the pad for a full 3 seconds (a quick tap will not change the setting).
• If the control panel is unresponsive, reset power by turning the dishwasher off at the breaker for 1 minute, then restore power and try again.

Lock mode behavior at a glance

Item	What happens when locked	What changes when unlocked
Buttons	Disabled	Work normally
Door	Can open/close	Can open/close
Starting a cycle	Will not run	Can start with START/RESUME

Why it matters

Control Lock prevents accidental button presses between cycles, which helps avoid unintended starts, canceled cycles, or changed options, especially in busy kitchens.

For the exact button location and indicator behavior on your control panel, follow the steps in the 66513979K015 owner’s manual.

Last updated: January 2026

To reset the control on your Kenmore Elite dishwasher model 66513979K015, press CANCEL/DRAIN twice, then choose a new cycle and press START/RESUME. This clears the current cycle and restarts the dishwasher from the beginning (control reset procedure in the 66513979K015 owner's manual).

Reset steps (control reset)

• Open the door slightly to stop the cycle; wait for spraying to stop.
• Open the door fully.
• Press CANCEL/DRAIN two times to reset the control.
• Select your new cycle and any options.
• Press START/RESUME.

If you need to stop and drain first

If there is water in the bottom of the tub, use a drain first, then reset.

• Open the door slightly; wait for spraying to stop.
• Press CANCEL/DRAIN once.
• Close the door within 3 seconds so it can drain.
• Let it drain completely (typically about 2 minutes), then press CANCEL/DRAIN twice to reset.

What “reset” does (and does not do)

Action	What it does	What it does not do
CANCEL/DRAIN twice	Resets the electronic control and clears the current cycle	Fix a failed part or wiring problem
CANCEL/DRAIN once + close door	Runs a drain cycle if water remains	Clean a clogged filter or drain path

Why it matters

A proper control reset is the fastest way to clear a stuck cycle, recover from an invalid option selection, or restart after opening the door mid-cycle. If the dishwasher still will not drain or restart after resetting, the issue is usually in the drain path or a component such as the drain pump.

If draining is the problem, the drain pump is a common suspect on this model; see the dishwasher drain pump WPW10348269 if you need a replacement.

Last updated: January 2026

Kenmore Elite dishwasher model 66513979K015 is a Kenmore-branded unit built by Whirlpool (the 665 model prefix is the key identifier). For parts and service procedures that match this exact dishwasher, use the 66513979K015 use and care guide and the 66513979K015 installation guide.

How we identify the manufacturer

Kenmore is a brand name; the actual manufacturer is typically identified by the model prefix.

• 665 prefix: Whirlpool-built Kenmore dishwashers
• The remaining digits identify the specific design series and features
• This matters because many internal components (pump, heater, racks) follow the manufacturer’s design

Why the manufacturer matters for parts

Knowing Whirlpool built this Kenmore Elite model helps you choose compatible replacement parts and troubleshoot using the right style of instructions.

• Electrical connectors and wire harness routing are manufacturer-specific
• Rack hardware and adjusters vary by design family
• Water system components (inlet valve, drain pump, sump) follow Whirlpool layouts

Examples of Whirlpool-style parts used on this model

What you’re fixing	Common part type	Example part for this model
Upper rack won’t stay on track	Rack stop / rail stop	Dishwasher dishrack slide rail stop, upper WPW10195622
Dishwasher not draining	Drain pump	Dishwasher drain pump WPW10348269
Poor cleaning / debris in sump	Filter	Dishwasher filter W10872845

Why it matters

When you match parts and procedures to the Whirlpool-built 665-series platform, you reduce fitment issues and avoid repeat repairs, especially on rack components, drainage, and water fill problems.

Last updated: January 2026

Common problems on the Kenmore Elite 66513979K015 dishwasher are no-start conditions, draining problems, poor cleaning, leaks, and drying issues. Most of these trace back to loading or latch problems, clogged filters or drain paths, or a failed component such as a pump, inlet valve, or heater; use the 66513979K015 owner's manual troubleshooting chart to narrow it down.

Most common symptoms and what usually causes them

• Dishwasher will not run: door not fully closed and latched, Start/Resume needs to be pressed again, tripped breaker or blown fuse, or a control issue.
• Won’t drain: kinked drain hose, disposer knockout plug not removed, food obstruction in the drain path, or a weak drain pump.
• Detergent remains in dispenser: door not latching, spray blocked by large items, or dispenser not opening.
• Hard water residue or cloudy glassware: very hard water, no rinse aid, or infrequent filter cleaning.
• Odors or noise: debris in the filter area, drain path restriction, or items contacting the wash system.

Quick checks we recommend first (fast, no parts)

• Confirm the door closes and latches; re-load tall items so they do not interfere with closing.
• If Start/Resume is blinking, close the door and press Start/Resume.
• Check the home circuit breaker or fuse.
• Inspect the drain hose for kinks and verify the disposer inlet knockout plug is removed (if connected).
• Clean the filter area regularly; hard water needs extra maintenance.

Parts that commonly fix these issues on model 66513979K015

Symptom	Common part to check	Example part for this model
Not draining	Drain pump, drain hose	Dishwasher drain pump WPW10348269, dishwasher drain hose 8269144A
Not filling or fills slowly	Water inlet valve	Dishwasher water inlet valve W11175771
Poor drying	Heater	Dishwasher heater W10703867
Poor cleaning	Filter, spray arm	Dishwasher filter W10872845, dishwasher spray arm WPW10195601

Why it matters

Catching a simple cause (like a kinked hose, blocked drain path, or hard-water buildup) prevents repeat cycle failures and helps protect the pump, heater, and control from extra strain.

Last updated: January 2026