Kenmore 11076912691 gas dryer Parts

Your Kenmore dryer’s model number is printed on the appliance ID label; for model 11076912691, you’ll use that exact number to match the correct gas dryer parts, diagrams, and troubleshooting steps. The label is usually easy to spot once you know the common locations.

Check these spots first (in order):

• Inside the dryer door opening on the cabinet frame
• On the back panel of the dryer
• On the front frame behind the door (near the latch area)
• Near the lint screen housing (some designs place the label nearby)
• On the side panel near the lower front (less common)

Record the full model number exactly as shown, including all digits.

• Use the full model number, not just the “110” prefix.
• If the label is worn, take a clear photo and zoom in to confirm digits.
• Match the symptom to the correct part category (heat, drum movement, door, airflow).
• For common “no heat” or “won’t start” issues, start with safety and airflow checks before replacing parts.

Kenmore model numbers can look similar across different dryer builds; using the exact model number (like 11076912691) prevents mismatched components such as thermostats, fuses, and drum support parts.

If you’re troubleshooting after identifying the model, use gas dryer wont heat troubleshooting video to narrow down likely causes.

Last updated: February 2026

A Kenmore gas dryer like model 11076912691 typically lasts 13 years with normal household use and routine vent and lint maintenance. Keeping airflow strong and replacing worn drive parts on time is what most often determines whether it reaches that full service life.

• Vent restriction (long runs, crushed flex duct, clogged hood)
• Lint buildup inside the cabinet and blower housing
• Overloading the drum and running repeated high-heat cycles
• Worn drum support and drive components (belt, idler pulley, rollers)
• Heat system cycling issues from failed thermostats or fuses

• Clean the lint screen every load; replace a torn or warped lint screen such as screen W10120998
• Confirm strong airflow at the outside vent hood while the dryer runs
• Clean the vent duct at least yearly (more often with long vents)
• Vacuum lint from the blower area and base periodically (power off first)
• Stop using the dryer if it overheats or shuts off mid-cycle; address airflow and safety parts

A dryer that is overheating or taking too long to dry wears out faster and can repeatedly open safety devices like the thermal fuse. If you suspect a blown fuse, use how to tell if a fuse is blown and consider replacing the correct safety part for this model, such as dryer thermal fuse WP3390719.

Last updated: March 2026

For Kenmore gas dryer model 11076912691, the most commonly replaced parts are the wear items in the drive system (idler pulley, belt-related supports) and airflow and heat-safety parts (thermal fuse, thermostats). These parts address the most frequent complaints: noise, no heat, and long dry times.

• Dryer idler pulley 279640 (squealing, belt not tensioned)
• Dryer thermal fuse WP3390719 (won’t run or stops, often after overheating)
• Dryer operating thermostat WP3387134 (poor temperature control, long dry times)
• Dryer high-limit thermostat W11050897 (overheating protection, heat cycling issues)
• Dryer blower wheel WP697772 (weak airflow, rumbling, poor drying)
• Dryer moisture sensor WP3387223 (auto cycles end too soon or run too long)

• Confirm the model tag reads 11076912691 (exact match matters)
• Unplug power and shut off gas before opening the cabinet
• Check and clean the vent system end-to-end
• Inspect the belt path and idler movement for binding
• Use a meter for electrical parts; see how to use a multimeter to test electrical parts video

Replacing the correct part the first time prevents repeat failures. For example, a new thermal fuse will blow again if the vent is still restricted, and a new idler pulley will not stay quiet if the belt path is misrouted or the drum supports are worn.

Last updated: March 2026