Kenmore 66513743K602 undercounter dishwasher Parts

No. Most built-in (undercounter) dishwashers are designed to fit a standard cabinet opening around 34 inches high, and many stand about 33-7/8 inches tall with the wheels removed. For Kenmore model 66513743K602, the installation guide shows it can fit a 33-7/8 inch cutout when the rear wheels are removed. See the 66513743K602 installation guide for the exact cutout and leveling details.

Typical dishwasher height ranges (what you should expect)

Most undercounter dishwashers are built to match common kitchen cabinet openings, not a single fixed appliance height.

• Standard cabinet opening height is commonly 34 inches minimum
• Some models can be lowered slightly by adjusting leveler legs or removing wheels
• Flooring changes (tile, built-up floors) can reduce usable opening height
• Countertop thickness and insulation can affect clearance

What the 66513743K602 installation specs mean

The 66513743K602 installation instructions call out two key numbers:

Measurement	What it refers to	Typical use
34" minimum cutout height	Cabinet opening height needed in many installs	Standard fit under most counters
33-7/8" cutout (with wheels removed)	Reduced-height fit option	Tight openings, harder to slide in

If your opening is tight, measure from the lowest point under the countertop to the floor, then plan leveling and wheel position accordingly.

Quick measuring checklist before you buy or install

• Measure opening height at the left, center, and right (use the lowest)
• Confirm opening width and depth are clear of pipes and wiring
• Check for built-up flooring in front of the dishwasher
• Verify the dishwasher can be leveled without forcing the countertop
• Plan floor protection if you need to remove wheels and slide the unit in

Why it matters

Dishwasher height is about fit and sealing. If the unit sits too low or too high, you can end up with poor door alignment, vibration noise, or gaps that affect performance and stability.

Last updated: January 2026

On Kenmore dishwasher model 66513743K602, an F2 E2 code typically points to a user interface (keypad) communication issue. We reset it by clearing the current cycle first, then restoring power to reboot the control and user interface; follow the button sequence in the 66513743K602 owner's manual.

Quick reset steps (most effective)

• Press CANCEL/DRAIN and let the dishwasher run the 2-minute drain (door must be closed).
• When the drain finishes, wait 10 seconds.
• Turn power off at the breaker for 1 minute, then turn it back on.
• Close the door fully, then press START/RESUME to begin a cycle.
• If the code returns immediately, avoid pressing multiple keys rapidly; press one key at a time.

If the code comes back: what to check next

F2 E2 is often triggered by a stuck key, moisture in the console, or a loose connection between the control panel and the main control.

• Power off at the breaker before inspecting anything
• Check for stuck or physically damaged buttons on the control panel
• Look for moisture around the console area; let it dry completely
• Reseat the console wiring connections (if accessible)
• If the dishwasher will not respond to any keys, the main control may not be reading the user interface

Common parts related to “no response” or control issues

These parts are not guaranteed fixes for F2 E2, but they are commonly involved when the dishwasher will not accept inputs or behaves erratically.

Symptom	Most likely area	Example part on this model
Keys do not respond, lights act odd	Main control / power feed	Dishwasher electronic control board WPW10285179
Dishwasher appears dead, no lights	Power interruption protection	Fuse W10258275

Why it matters

Clearing the cycle with CANCEL/DRAIN prevents starting a new wash with a partially completed program, and a power reset forces the control board and user interface to reboot and re-sync. That combination resolves many intermittent keypad communication faults.

Last updated: January 2026

Common problems we see on the Kenmore 66513743K602 dishwasher include not starting or stopping mid-cycle (door not fully latched or power interruption), poor drying (no rinse aid or air-dry selected), drainage problems, leaks, and unusual noises. Many issues trace back to loading, water supply, or a worn part.

Most common symptoms and what to check first

• Won’t start or stops during a cycle: confirm the door is closed tightly and latched; verify the cycle selection and household power (breaker or fuse). See the 66513743K602 owner’s manual for the model’s troubleshooting checks.
• START/RESUME light flashing: the door was opened during the cycle or power was interrupted; close the door and resume.
• Dishes not dry: avoid overloading, use rinse aid, and choose a heated dry option when needed.
• Grinding or crunching noise: a hard object may be in the wash module; if noise continues after a full cycle, service is typically needed.
• Leaks: inspect the door seal area for gaps, tears, or debris; also check the drain hose routing and clamps.

Parts that commonly solve these problems

If basic checks do not fix the issue, these parts are frequent culprits on this model:

• Heating and drying issues: dishwasher heating element W10518394
• Not running (no power symptoms): fuse W10258275
• Not draining or standing water: dishwasher drain pump WPW10348269
• Leaks at the door: dishwasher door seal W10542314
• Fill problems (no water or slow fill): dishwasher water inlet valve W10648041

Quick symptom-to-likely-cause guide

Symptom	Most likely causes	Best first action
Dishwasher won’t run	Door not latched, power issue, overload reset	Check latch and breaker/fuse; wait a few minutes for motor reset
Water left in tub	Clog, drain pump issue, hose issue	Clean filters/sump area; verify drain path
Dishes wet after cycle	No rinse aid, air-dry used, overloading	Add rinse aid; switch to heated dry; improve loading
Leaking at front	Door seal worn, door not closing square	Clean/inspect seal; confirm door closes evenly

Why it matters

Catching simple causes early (door latch, rinse aid, loading, power) prevents repeat wash failures, reduces leaks, and helps the heating and pump system run at the right temperature and flow for proper cleaning.

Last updated: January 2026