Kenmore 11028922791 washer Parts

Your Kenmore washer model number is printed on the model and serial number plate on the machine. For Kenmore model 11028922791, use that full number (and the serial number) when ordering washer parts or looking up operating and installation details in the 11028922791 owner's manual.

Where to look on the washer

On Kenmore washers like model 11028922791, the model and serial number plate is on the cabinet. Common places to check include:

• Under the lid near the tub opening (top-load washers)
• Along the rim of the lid opening on the cabinet
• On the back panel near the power cord entry
• Behind the control console area (visible from the rear on some versions)

What the model number looks like (and why it matters)

Kenmore model numbers often start with 110 (a common Kenmore prefix). Using the exact model number helps us match the correct fit for items like a lid switch, drain pump, or inlet valve.

Quick ID checklist

• Write down the model number and serial number exactly as shown
• Use the full model number (for example: 11028922791, not just “110”)
• If the plate is hard to read, take a clear photo before cleaning it
• Keep the information with your purchase records for future repairs

Common parts you may match by model

Once you have the model number, you can confidently choose model-correct replacement parts. Examples for this washer include:

Symptom	Common part to check	Example part for this model
Won’t spin or stops when lid opens	Lid switch	Washer lid switch WP3949238
Won’t drain or drains slowly	Drain pump	Washer drain pump WP3363394
Won’t fill or fills slowly	Inlet valve	Washer inlet valve 285805

Why it matters

Kenmore washers can look similar across many series, but internal components (like the timer, gear case, or drive system) can vary by model. Using the exact model number prevents ordering the wrong part and speeds up troubleshooting.

Last updated: February 2026

Yes, repairing a Kenmore washer is usually worth it when the fix restores reliable washing and spinning for far less than replacing the machine. For Kenmore model 11028922791, many common failures involve serviceable parts (lid switch, drain pump, drive coupling) that can extend the washer’s usable life.

A simple way to decide (repair vs. replace)

Use these practical checkpoints before spending money:

• Start with the symptom: no spin, no drain, won’t agitate, leaks, or excessive vibration.
• Compare total repair cost (parts plus labor) to a replacement washer.
• Prioritize safety and basics: proper grounding, stable power, and correct installation setup.
• Check installation items first: an unlevel washer or loose front-leg nuts can cause vibration and “bad washer” symptoms.
• Choose repairs that are “long-lasting”: mechanical wear parts often give a strong return when replaced correctly.

Repairs that are commonly worth it on this style of Kenmore top-load washer

These are frequent, high-impact fixes for a direct-drive Kenmore/Whirlpool-built top-load design:

Symptom	Common cause	Example part for 11028922791
Won’t spin or acts “dead” when lid closes	Lid switch not closing circuit	Washer lid switch WP3949238
Won’t drain or drains slowly	Drain pump jammed or worn	Washer drain pump WP3363394
Agitates/spins poorly, grinding, intermittent drive	Motor coupling worn/broken	Coupling 285753A
Agitator “ratchets” or won’t move clothes well	Worn agitator dogs	Agitator dog 80040

Why it matters

A washer that is installed correctly and repaired with the right parts can deliver years of dependable operation. Your manual also highlights setup checks (leveling, tight front-leg nuts, electrical requirements) that directly affect performance and vibration, so correcting those can prevent repeat failures.

What we recommend before ordering parts

1. Confirm the washer is level and the front-leg nuts are tight.
2. Verify the water faucets are on and hoses are not kinked.
3. Match the failure to the most likely part (table above), then follow the troubleshooting and operating guidance in the 11028922791 owner’s manual.

Last updated: February 2026

A Kenmore washer typically lasts 10 to 15 years with normal household use. For Kenmore model 11028922791, steady care (correct loading, proper detergent use, and addressing small leaks or noises early) helps you reach the longer end of that range; heavy use and repeated overloading shorten it.

What affects washer lifespan the most

• Load size and balance: frequent overloading strains the drive system and suspension.
• Water quality: hard water can accelerate valve and internal buildup issues.
• Drain performance: slow draining makes the pump work harder and can lead to repeated cycle problems.
• Lid switch and safety interlocks: a failing switch can stop spin and cause repeated restarts.
• Agitation and drive wear: worn agitator components reduce cleaning and increase mechanical stress.

Common wear items to watch on this model

If performance changes, these parts are frequent suspects on top-load Kenmore washers like 11028922791:

Symptom	Often related part	What you notice first
Won’t spin or stops mid-cycle	Washer lid switch WP3949238	No spin with lid closed, intermittent operation
Won’t drain or drains slowly	Washer drain pump WP3363394	Water left in tub, humming during drain
Agitator slips or doesn’t “grab” clothes	Agitator dog 80040	Upper agitator movement is weak or one-directional
No fill or slow fill	Washer inlet valve 285805	Long fill times, wrong temperature mix

Maintenance habits that extend life

We recommend these practical steps (they matter more than “deep cleaning” routines):

• Keep loads below the top of the basket and distribute items evenly.
• Use the right amount of detergent; excess suds can cause poor rinsing and extra wear.
• Check fill hoses and the drain hose for kinks, cracking, or seepage.
• If you hear new grinding, squealing, or banging, stop using the washer and inspect before it worsens.
• Follow the operating and care guidance in the 11028922791 owner's manual.

Why it matters

A washer usually fails gradually, not suddenly. Catching early symptoms (slow drain, weak agitation, intermittent spin) helps you replace a lower-cost part like a lid switch, pump, or agitator component before bigger assemblies take damage.

Last updated: February 2026