Kenmore Elite 66513933K015 undercounter dishwasher Parts

Yes. The Kenmore Elite dishwasher model 66513933K015 uses an ULTRA WASH filtration system with two filters (an upper filter assembly and a lower filter) located at the bottom center of the tub; cleaning them periodically helps maintain peak cleaning performance.

Where the filter is and what it does

The filtration system is designed to keep food soil from being recirculated and to protect the pump.

• Upper filter assembly: helps keep oversized items and fine particles out of the pump
• Lower filter: helps keep food from being recirculated onto dishes
• Location: bottom center of the dishwasher tub

When to clean the filters

Clean the filters when you notice any of the following:

• Visible objects or soil on the upper filter assembly
• Reduced cleaning performance (soil left on dishes)
• Dishes feel gritty after a cycle
• Odors that persist even after running a hot cycle

Basic filter care (safe, quick routine)

Use this simple routine to keep the filtration system working properly.

Task	What to do	Typical time
Remove filters	Follow the steps in the 66513933K015 owner's manual	2 to 5 minutes
Clean	Rinse under warm water; use a soft brush if needed	5 to 10 minutes
Reinstall	Lock the upper filter assembly in place before running cycles	2 to 5 minutes

Why it matters

A clean filter helps your Kenmore Elite dishwasher maintain strong wash performance, reduces the chance of gritty residue on dishes, and supports proper water flow through the sump and pump.

Last updated: January 2026

To reset the controls on your Kenmore Elite dishwasher model 66513933K015, press CANCEL/DRAIN twice, then reselect your cycle and press START/RESUME. This clears the current cycle and gets the control ready to start fresh (it may drain first). See the 66513933K015 owner's manual for the exact button sequence for your console.

Reset steps (control reset)

• Open the door slightly to pause the cycle; wait for spraying to stop.
• Open the door fully.
• Press CANCEL/DRAIN twice to reset the control.
• Select the new cycle and options.
• Press START/RESUME.
• Close the door promptly so the dishwasher can start (or finish draining).

What you should see after pressing CANCEL/DRAIN

In many cases, the dishwasher will run a short drain to clear water from the bottom before it will restart.

What happens	What it means	What to do
Drain pump runs for a short time	Normal cancel and drain	Let it finish, then start a new cycle
Lights change and cycle stops	Control accepted the reset	Pick a new cycle and press START/RESUME
Unit will not drain	Possible drain restriction or pump issue	Check the drain path and consider the dishwasher drain pump WPW10348269

If it still will not reset or start

These checks solve most “won’t reset” complaints on undercounter dishwashers:

• Make sure the door is fully latched; a weak latch can prevent START/RESUME from engaging.
• Wait 2 minutes after CANCEL/DRAIN; some models keep the drain cycle active briefly.
• Check the tub for standing water and clear the filter area if needed.
• Inspect the drain hose for kinks or a blocked high loop/air gap.
• If the dishwasher hums but does not move water, the drain pump or a blockage is likely.

Why it matters

A proper reset clears a stuck cycle and forces the control to reinitialize. If the dishwasher cannot drain during the reset, it often points to a drain-path issue (hose, filter area, or drain pump) rather than a keypad problem.

Last updated: January 2026

Common problems on the Kenmore Elite 66513933K015 dishwasher include not draining, not starting, poor cleaning, water left in the tub, and long cycle times. Most issues trace back to loading interference, a clogged filter, a kinked drain hose, low incoming water temperature, or a failing pump or valve (see the 66513933K015 owner's manual).

Most common symptoms and what to check first

• Dishwasher does not run: confirm the door is fully closed and latched; press Start/Resume if the light is blinking.
• Water remains in tub or won’t drain: verify the cycle completed; check for drain hose kinks and disposer knockout plug (if connected).
• Detergent remains in dispenser: make sure large items are not blocking the dispenser door; use fresh, lump-free detergent.
• Food soils remain on dishes: confirm proper loading; clean and reinstall the filter; use the right cycle for soil level.
• Cycle runs too long: some cycles can run up to about 3 hours; heated dry and other options add time.
• Suds/foam in tub: only use automatic dishwasher detergent; too much detergent or a missing rinse aid cap can cause problems.

Parts that commonly solve these problems on this model

If basic checks do not fix the issue, these model-matched parts are common culprits:

Symptom	Likely area	Example model-matched part
Won’t drain, water left in tub	Drain system	Dishwasher drain pump WPW10348269
Poor cleaning, debris recirculating	Filtration	Dishwasher filter W10872845
Won’t fill or fills slowly	Water supply	Dishwasher water inlet valve W11175771
Poor drying, cool water	Heating circuit	Dishwasher heater W10703867
Leaks at the bottom of the door	Door sealing	Seal WPW10497235

Why it matters

Catching the root cause early helps prevent repeat wash failures, standing water odors, and water damage. For example, a dirty filter can cause poor cleaning and drainage complaints at the same time, and low water temperature can extend cycle time while reducing performance.

Quick safety and setup notes

• Turn off power at the breaker before testing electrical parts.
• If the dishwasher may be exposed to freezing temperatures, follow winterizing guidance in the 66513933K015 installation guide.
• For electrical checks, use a meter and proper technique (see how to use a multimeter to test electrical parts video).

Last updated: January 2026