Kenmore 11013202200 washer Parts

Your Kenmore washer model number is printed on the model and serial number plate; on Kenmore model 11013202200, it’s typically located under the lid on the top-load cabinet. Once you have the full model number, you can match the correct parts, diagrams, and instructions.

Where to look on Kenmore washers

Check these common locations in this order:

• Under the lid along the top rim of the tub opening (most Kenmore top-load models like 11013202200)
• Inside the door opening on the front frame (front-load models)
• Back panel near the power cord entry or lower corner
• Behind the control panel (some designs)
• On the cabinet side near the base (less common)

For the exact location callout for this washer, use the 11013202200 owner's manual.

What the model number looks like (and what to write down)

Record the model number exactly as shown, including all digits.

What to capture	Example for this washer	Why it matters
Model number	11013202200	Ensures parts fit your exact Kenmore washer
Serial number	(varies)	Helps confirm production run and compatible revisions
Stock number (if shown)	13202	Useful cross-reference in some manuals

Why it matters

Kenmore uses many similar-looking washer designs. The model number is the only reliable way to select the right replacement part (for example, a drain pump, inlet valve, or motor coupling) and avoid returns.

Quick tip if you are ordering parts

If your washer will not drain or spin, confirm the model number first, then compare symptoms to common fixes. For example, a no-drain issue often points to the washer drain pump WP3363394, while a no-agitate/no-spin issue can involve the washer motor coupling 285753A.

Last updated: February 2026

A Kenmore washer typically lasts 10 to 15 years with normal household use. For Kenmore model 11013202200, consistent care (proper installation, correct loading, and good water supply) helps you reach the longer end of that range; worn drive and water parts can shorten it.

Typical lifespan and what affects it

Most top-load Kenmore washers like 11013202200 land in this range, and these factors make the biggest difference:

• Load size and frequency (overloading accelerates wear)
• Installation quality (level floor, correct drain setup)
• Water conditions (very hard water can increase valve and seal issues)
• Detergent habits (too much detergent can cause residue and odors)
• Early repair of small problems (leaks, slow drain, unusual noises)

Parts that commonly limit washer life

When a washer stops agitating, spinning, or draining reliably, these are frequent wear items to check first:

• Washer motor coupling 285753A (drive connection between motor and transmission)
• Washer drain pump WP3363394 (draining problems, humming, or water left in tub)
• Washer inlet valve 285805 (slow fill, no fill, or leaking into tub)
• Gear case 3360629 (grinding noise, no spin, oil leak)

Quick symptom-to-part guide

Symptom	Common cause	Part to consider
Won’t spin or agitate	Broken drive connection	Motor coupling
Won’t drain	Clogged or failed pump	Drain pump
Won’t fill or fills slowly	Valve or supply issue	Inlet valve
Loud grinding, oil leak	Internal drive wear	Gear case

Why installation and basics matter

A washer that is installed correctly runs with less vibration and strain. For this model, the installation instructions call out key requirements like a level floor, proper standpipe height, and a grounded 3-prong outlet; those basics reduce long-term wear and nuisance failures. Use the 11013202200 installation guide for the exact setup requirements.

Practical ways to extend lifespan

• Keep loads balanced; avoid washing heavy items alone
• Use the right water level and temperature settings for the load
• Check fill hoses and the drain hose routing periodically
• Address leaks quickly to protect bearings, seals, and the gear case
• If performance changes, confirm cycle and control settings in the 11013202200 owner's manual

Last updated: February 2026

For Kenmore washer model 11013202200, a hard reset is a simple power reset: unplug the washer (or switch off the breaker) for 1 minute, then restore power and try a normal cycle. This clears minor control glitches without changing installation settings.

Hard reset steps (power reset)

• Press Pause/Cancel once to stop the cycle.
• Unplug the washer from the outlet (or turn the breaker OFF).
• Wait 60 seconds.
• Restore power.
• Select a Rinse/Spin or Normal cycle and press Start.

If the washer still acts up

A “reset” will not fix a mechanical problem (no drain, no spin, loud grinding). These checks usually pinpoint what is really happening:

• No drain or slow drain: check the drain hose for kinks and verify the standpipe is not clogged; a failing pump can also cause this (see washer drain pump WP3363394).
• Won’t spin or makes a rattling/grinding sound: a worn drive system component is common on this style of Kenmore washer (see washer motor coupling 285753A and clutch 285785).
• Fills incorrectly or won’t fill: confirm both faucets are fully open and inlet screens are not blocked; the inlet valve can be the cause (see washer inlet valve 285805).
• Excessive vibration: confirm the washer is level and the feet are locked down.

Quick symptom-to-next-step table

What you see	What to do next	Likely area
Display/cycle seems “stuck”	Do the 1-minute power reset	Control logic glitch
Water remains in tub	Check hose, then test drain function	Drain path or pump
Motor runs but basket does not move	Inspect drive coupling/clutch	Drive system
Shakes or bangs	Re-level and tighten leveling nuts	Leveling/suspension

Why it matters

A hard reset is the fastest way to clear a temporary control issue. If the same symptom returns right away, the washer is usually reacting to a real condition (drain restriction, unbalanced load, worn coupling, or a failing pump), and troubleshooting the specific system saves time and repeat interruptions.

For model-specific operating and setup details, use the 11013202200 owner’s manual.

Last updated: February 2026

Yes, repairing a Kenmore washer is worth it when the fix restores reliable washing and spinning for less than replacing the machine. For Kenmore model 11013202200, common wear items (like the motor coupling or drain pump) are straightforward repairs that often extend the washer’s life.

Quick way to decide (repair vs. replace)

Use these checkpoints before spending money on parts or labor:

• Repair it when the problem is a single failed part (no-spin, no-drain, leaking hose) and the tub and cabinet are in good shape.
• Repair it when the washer is otherwise quiet and stable (no loud grinding, no severe vibration).
• Replace it when the repair involves major drive system damage (gear case plus multiple related parts) and the total cost approaches a new washer.
• Replace it when there is persistent tub bearing/seal leakage that has damaged multiple components.
• Repair it when you can confirm the symptom and part match using the 11013202200 owner’s manual.

Common repairs that are usually “worth it” on this model

These are frequent, targeted fixes for top-load Kenmore/Whirlpool-built washers like 11013202200:

Symptom	Likely area	Example part to check
Motor runs but won’t agitate/spin	Drive connection	Washer motor coupling 285753A
Won’t drain or drains slowly	Drain system	Washer drain pump WP3363394
Fills slowly or won’t fill	Water supply/valve	Washer inlet valve 285805
Spins poorly, burning smell, noisy spin	Clutch/drive	Clutch 285785

Why it matters

A focused repair (one failed part) typically restores performance quickly and avoids the installation requirements of a new washer (level floor, correct water pressure, grounded outlet). Proper setup also prevents noise and vibration issues after the repair, as outlined in the 11013202200 installation guide.

Cost and longevity rule of thumb

• Typical washer lifespan: 10 to 14 years.
• If your repair cost is well under half the price of a comparable new washer and the machine is otherwise solid, repairing is the better value.

Last updated: February 2026