Kenmore 11097591240 gas dryer Parts

On the Kenmore 11097591240 gas dryer, CL means the control lock (child lock) is on, so most buttons will not respond until you unlock the controls.

• The dryer may still power on, but Start will not run a cycle
• Button presses may beep or do nothing
• The display can alternate between CL and the estimated time remaining
• Cycle settings may not change
• The door can usually still be opened

Because the exact button varies by control panel version, use this quick process:

1. Look for a button labeled Control Lock, Lock, or a padlock icon.
2. Press and hold that button for about 3 seconds.
3. If nothing happens, try pressing and holding End of Cycle Signal or Dryness Level for 3 seconds (common Kenmore 110-series layouts).

• Make sure the dryer is not in the middle of a cycle; press Cancel/Stop first
• Unplug the dryer (or switch off the breaker) for 1 minute, then restore power
• If the console buttons are unresponsive or “stuck,” inspect the door switch and latch alignment; a worn latch can cause confusing control behavior (see catch 279570)

Control lock prevents accidental cycle changes and unintended starts. If you forget it is enabled, the dryer can look “dead” even though power is present.

For more help with display messages and troubleshooting steps, use our Kenmore 110 series electronic control model dryer error codes guide.

Last updated: February 2026

For Kenmore gas dryer model 11097591240, the correct drum belt size is the one matched to your exact model’s parts list; Kenmore belt lengths vary by design, so using the model-specific lookup prevents ordering a belt that is too long or too short.

We recommend confirming by model number (11097591240) and the belt’s rib/groove style.

• Match the belt to the exact model number on the dryer’s ID tag
• Confirm whether the belt is ribbed (multi-rib) or flat
• Compare the old belt’s markings (if readable)
• If the belt snapped, check for a seized drum support roller or idler pulley at the same time

Many Kenmore 110-series style dryers use a ribbed belt that is about 92 1/4 inches long and about 1/4 inch wide, but other common lengths exist (roughly 89 1/2 to 93 1/2 inches) depending on drum size and chassis.

A belt that is even slightly off can cause squealing, thumping, poor tumbling, or repeated belt failure. When a belt breaks, we also check the wear parts that load the belt system.

• Worn drum rollers: support WPW10314173
• Sticking or noisy tensioner: dryer idler pulley 279640
• Loose pulley mount hardware: bracket W10837240

Disconnect power before servicing. For gas dryers, shut off the gas supply before opening the cabinet.

Last updated: February 2026

Your Kenmore dryer’s model number is printed on the appliance ID label. On model 11097591240 (gas dryer), you’ll typically find that label just inside the dryer door opening on the cabinet frame, or on the back of the dryer near the top.

Check these common spots in this order:

• Inside the door opening on the cabinet frame (most common)
• On the back panel near the top edge
• Along the door opening edge where the door closes
• On the lower front frame area (less common)

Kenmore model numbers are usually a long number string. For this page, the model is 11097591240.

Use the full model number exactly as shown on the label (including any extra digits) when you search for parts.

The model number is how we match the correct Kenmore gas dryer parts, diagrams, and troubleshooting info. Even small model-number differences can change items like the drive system, door latch style, or safety components.

You can still narrow it down by matching visible parts and features:

• Compare the door latch style (for example, the catch 279570)
• Check the lint screen style and location (for example, the screen W10120998)
• Match common wear parts if you are diagnosing noise or no-heat symptoms (for example, the dryer thermal fuse WP3390719)

Last updated: February 2026

To reset your Kenmore 11097591240 gas dryer, we recommend doing a simple power reset first: turn the dryer off, unplug it (or switch the breaker off) for 1 minute, then restore power and try a cycle. This clears many control glitches without replacing parts.

• Press Power/Cancel to stop the cycle.
• Unplug the dryer (or turn the breaker OFF).
• Wait 60 seconds.
• Restore power.
• Open and close the door once, then start a timed dry cycle.

A reset will not fix a failed safety device or a mechanical problem. Check these common causes next:

• No heat or stops mid-cycle: a blown thermal fuse can cut operation; see dryer thermal fuse WP3390719.
• Runs but has weak airflow: a clogged blower wheel or venting issue can cause overheating and shutdowns; see dryer blower wheel WP697772.
• Won’t start: a door latch issue can prevent the motor from running; see catch 279570.
• Squealing or thumping: drum support rollers can bind and strain the motor; see support WPW10314173.
• Humming but drum won’t turn: the idler pulley can seize or the belt system can bind; see dryer idler pulley 279640.

Resetting is a safe first step because it restores the control to a known state. If the problem returns immediately, we focus on airflow, door-latch sensing, and drive components because those issues commonly stop a gas dryer from running normally.

Last updated: February 2026

Most electric dryers run on a 240-volt circuit, but your Kenmore 11097591240 is a gas dryer, so it does not use 240 volts for heating. Gas dryers typically use a standard 120-volt outlet to power the motor, controls, and igniter system while heat comes from the gas burner.

In most homes, a gas dryer plugs into a 120V, 60 Hz grounded outlet (the same style outlet used for many household appliances).

Common electrical requirements you will see for gas dryers:

• 120V power for the drive motor and timer/control board
• A dedicated circuit is preferred to prevent nuisance trips
• Proper grounding is required for safe operation
• The dryer still needs a correctly installed exhaust vent for airflow

Using the correct voltage helps prevent no-start problems, blown fuses, and wiring damage. If a gas dryer is not running, the issue is usually in the door switch, thermal fuse, motor circuit, or airflow related overheating, not a missing 240V supply.

We recommend checking these common causes first:

• Confirm the outlet has power and the breaker is on
• Make sure the door fully closes and latches
• Check for a blown thermal fuse such as the dryer thermal fuse WP3390719
• Inspect the belt and idler system (a seized idler can stop the drum from turning)
• Clear lint buildup and verify strong airflow at the outside vent hood

For step-by-step no-start diagnosis, use our gas dryer wont start troubleshooting video.

Last updated: February 2026