Maytag MDG6000BWW gas dryer Parts

For model Maytag MDG6000BWW, it is a gas dryer (it uses a gas burner and igniter to create heat, not an electric heating element). You can order model-matched gas-heat parts from the MDG6000BWW parts list or search by model on Sears PartsDirect.

How to tell on your MDG6000BWW (quick checks)

• Look for a gas supply line connected to the dryer (usually black iron pipe or flexible gas connector).
• Check for a burner/igniter area behind the lower front access panel.
• During a heat cycle, you may see the igniter glow briefly before the burner lights.
• The electrical plug is typically standard 120V for a gas dryer (electric dryers commonly use a larger 240V plug).

Parts that confirm it is a gas dryer

These MDG6000BWW parts are specific to the gas heating system:

• Gas igniter 4391996
• Gas sensor WP338906
• Holding coil 279834

Why it matters

Gas and electric dryers use different heating components and troubleshooting steps. Knowing MDG6000BWW is gas helps you choose the right replacement parts (igniter, radiant sensor, gas valve coils) and avoid ordering an electric heating element that will not fit.

Common symptom-to-part map (gas heat)

Symptom	Most common gas-heat checks	Parts often involved
Runs but no heat	Airflow restriction, burner not lighting	Igniter, radiant sensor, coils
Heat starts then stops	Coils weakening as they warm up	Gas valve coils
Long dry times	Venting, lint buildup, weak airflow	Lint filter, blower wheel

If your dryer runs but will not heat, we recommend following a gas-dryer heat diagnostic like gas dryer wont heat troubleshooting video.

Last updated: February 2026

Maytag dryer capacity depends on the exact model. For the Maytag MDG6000BWW gas dryer, the capacity is typically in the 6.0 to 7.0 cu. ft. range for full-size dryers of this design; use that range for load planning and basket sizing rather than assuming a newer 7.3 cu. ft. platform.

How to estimate capacity for MDG6000BWW in real use

We recommend treating MDG6000BWW as a full-size dryer and loading by basket volume and airflow, not by weight.

• Fill the drum loosely to about 1/2 to 2/3 full for best tumbling
• Dry bulky items (comforters, jackets) as single large items when possible
• Avoid packing the drum tight; gas dryers need airflow to heat and dry evenly
• If loads take longer than normal, check venting and lint filtration first

Why capacity varies across Maytag dryers

Maytag has produced multiple dryer platforms over the years (different drum sizes, cabinet depths, and airflow designs). That is why a capacity claim from a current model line does not transfer cleanly to MDG6000BWW.

Dryer type	Typical capacity range	What you’ll notice
Compact dryer	3.4 to 4.4 cu. ft.	Smaller loads, faster cycles
Full-size dryer (common)	6.0 to 7.0 cu. ft.	Comforters fit, normal cycle times
Extra-large full-size	7.2 to 9.0 cu. ft.	Fewer loads, more room for bulky items

Why it matters

Capacity affects drying performance. Overloading reduces tumbling and airflow, which can cause longer dry times, higher heat stress on fabrics, and overheating that can trip safety devices.

If your MDG6000BWW is taking too long to dry, start with airflow basics: clean the lint screen and confirm the lint screen is intact and seating correctly. A damaged or missing screen can also let lint migrate into the blower housing.

Helpful parts for airflow and drying performance include the dryer lint filter WP33001808 and the dryer blower wheel 33001790. For more maintenance and efficiency tips, see how to use your clothes dryer efficiently. You can also search by model number on Sears PartsDirect if you need additional parts not listed here.

Last updated: February 2026

Your Maytag dryer’s model number is printed on the appliance’s identification label; once you find it, match that number to the parts list for your exact unit (for this page, the model is MDG6000BWW). Using the correct model number ensures you get compatible parts like a timer, igniter, or thermal fuse.

Where to find the model number on a Maytag gas dryer

Check these common label locations on Maytag dryers:

• Open the dryer door and look around the door opening (door jamb area)
• Look on the inside face of the door
• Check the back panel of the dryer cabinet
• Check the lower front area behind the toe panel or access panel (if equipped)
• Look near the lint screen housing (some designs place the label nearby)

What the label looks like (and what to write down)

The ID label typically includes both a model number and a serial number.

What to record	Example format	Why it matters
Model number	MDG6000BWW	Identifies the exact parts breakdown for your dryer
Serial number	Letters and numbers	Helps confirm production series when parts vary

Why it matters

Maytag dryer parts can look similar across models, but mounting points, electrical connectors, and gas burner components can differ. Using the exact model number helps you choose the right replacement part the first time.

Next step: match your model to the right parts

If your label shows MDG6000BWW, you are already on the correct parts page. Common parts customers replace on this model include the gas igniter 4391996 and the dryer thermal fuse WP33001762. For broader model searches and ordering, use Sears PartsDirect.

Last updated: February 2026