Kenmore 11070932990 gas dryer Parts

To tell what model your Kenmore dryer is, we look for the model and serial number plate on the dryer itself. On Kenmore model 11070932990, the plate is typically in the door opening area; once you have that full model number, you can match the correct parts and the right 11070932990 owner's manual.

Check these common locations on Kenmore dryers (starting with the most likely):

• Inside the dryer door opening on the cabinet frame (often the easiest spot)
• On the back panel of the dryer cabinet
• Near the lint screen housing area (depending on the design)
• On the inside of the front panel (visible after removing the lower access panel on some models)

Kenmore model numbers are usually a long string of digits. For this dryer, the model number is 11070932990. Using the exact model number helps us pull the correct diagrams and parts list, especially for common repairs like a no-heat issue (igniter, gas valve coils, thermal fuse) or a noisy drum (rollers, idler pulley).

• Write down the full model number and serial number exactly as shown
• Take a clear photo of the plate before ordering parts
• Use only the model number (not cycle names like “Heavy Duty” or “Normal”) for parts matching
• If the label is worn, try a flashlight at an angle to make the print easier to read

If you are troubleshooting symptoms after identifying the model, these are common part types for this gas dryer:

• Dryer thermal fuse WP3390719 (no heat or dryer stops)
• Igniter 279311 (no heat, burner will not light)
• Dryer valve coil kit 279834 (heats briefly, then stops heating)

Kenmore dryers can look similar across series, but internal components and wiring can differ. Using the exact model number ensures we guide you to the correct Kenmore diagrams, compatible parts, and the right operating details in the manual.

Last updated: February 2026

For the Kenmore 11070932990 gas dryer, a “heating element” is not the typical heat source; heat is produced by the gas burner system. Most no-heat repairs on this model land in the $25 to $350 range total, depending on which ignition or safety part is needed and whether you hire service.

Here are common price ranges we see for gas-dryer heat problems like “runs but won’t heat”:

• DIY parts only: about $25 to $200
• Professional labor: about $100 to $250 (varies by area and access)
• Total typical repair: about $150 to $350

If your dryer tumbles but doesn’t heat, these are the most common fixes:

• Dryer valve coil kit 279834 (often fails after warming up)
• Igniter 279311 (glow-bar style igniter)
• Dryer radiant sensor WP338906 (flame sensing)
• Dryer thermal fuse WP3390719 (opens if overheating occurs)
• Dryer high-limit thermostat W11050897 (temperature safety control)

On a gas dryer, poor airflow can overheat the burner area and open a safety device, which stops heat until the failed part is replaced and the venting issue is corrected.

Before buying parts, we recommend:

• Clean the lint screen and confirm strong airflow at the outside vent hood
• Check that the gas supply valve is fully open
• Run a timed cycle and listen for burner ignition (click, whoosh)
• Inspect the vent duct for kinks, crushing, or heavy lint buildup

For model-specific operating and cycle details (including temperature and cool-down behavior), use the 11070932990 owner’s manual.

Last updated: February 2026

Kenmore gas dryer model 11070932990 is a full-size (standard-width) dryer; most units in this Kenmore 110 platform measure about 27 inches wide, 27 to 29 inches deep, and 43 to 44 inches tall. For the exact cabinet dimensions for your specific configuration, use the 11070932990 owner's manual.

These are the most common exterior size ranges customers use for fit checks (doorway, alcove, and vent clearance):

• Width: ~27 inches
• Height: ~43 to 44 inches
• Depth (cabinet): ~27 to 29 inches
• Depth (with door closed): often slightly more than cabinet depth
• Clearance: leave space behind for the gas line and vent elbow

We recommend verifying with the manual and a quick tape-measure check so you account for handles, door curvature, and hookups.

• Measure width at the widest point of the cabinet
• Measure height from floor to the top of the cabinet
• Measure depth from the back panel to the front edge (then re-check including the door)
• Confirm the model on the model and serial number plate (commonly inside the door opening)

Correct sizing prevents crushed venting, kinked gas connections, and doors that cannot fully open. It also helps airflow stay strong, which improves drying performance and reduces overheating risk.

Last updated: February 2026