Frigidaire GLGQ2152EE3 dryer Parts

Yes. For your Frigidaire dryer model GLGQ2152EE3, looking up parts by the full model number is the most accurate way to match compatible replacement parts because it filters results to the exact drum, heating, gas, and control components used on that dryer.

How to find and use the model number

Use the complete model number exactly as shown on the dryer’s data tag, then cross-check diagrams and part lists.

• Find the model tag on the dryer cabinet (commonly inside the door opening or on the door frame area)
• Write the model number exactly, including all letters and numbers: GLGQ2152EE3
• Use the parts list and diagrams in the GLGQ2152EE3 owner's manual
• Confirm the part name and ID before ordering (especially for belts, bearings, and thermostats)
• If you are installing or moving the dryer, follow the GLGQ2152EE3 installation guide for safety and setup details

Common parts customers look up by model number

These are frequent wear items on this Frigidaire dryer; model-number lookup helps prevent ordering the wrong style.

Symptom	Likely area	Example part for GLGQ2152EE3
Drum not turning, squealing	Drum drive	Frigidaire dryer drum belt 134503600
Thumping, rumbling, drum play	Drum support	Dryer drum bearing kit 5303281153
No heat or overheating shutdown	Temperature safety	Thermal limiter 137032600

Why it matters

Dryer parts often look similar across Frigidaire models, but small differences (belt length, bearing style, sensor type, gas valve components) can change fit and performance. Using GLGQ2152EE3 ensures you get parts that install correctly and restore proper drying.

Last updated: February 2026

For a Frigidaire dryer like model GLGQ2152EE3, replacing a heating element typically costs about $200 to $400 total (part plus labor). If you do it yourself, the part is often about $80 to $200, with the final price depending on the exact heater assembly used.

Typical cost breakdown (part vs. labor)

Costs vary by region and service company, but these ranges are common for a standard in-home repair.

• Heating element part: $80 to $200 (electric models only)
• Labor: $120 to $250
• Service call/diagnostic (sometimes separate): $0 to $120
• Total typical installed cost: $200 to $400

Scenario	What you pay for	Typical total
DIY replacement	Part only	$80 to $200
Pro repair (most common)	Part + labor	$200 to $400
Higher-end service	Part + labor + separate trip/diagnostic	$300 to $500

Important model note for GLGQ2152EE3

GLGQ2152EE3 is commonly a gas dryer model family; gas dryers do not use an electric “heating element” the way electric dryers do. If your GLGQ2152EE3 is gas and will not heat, the repair cost is usually driven by ignition and flame components instead of a heater element.

• Ignition system issues: igniter, gas valve coils, flame sensor
• Airflow issues: lint screen, vent restriction, blower problems
• Temperature control issues: thermistor, thermal limiter

Parts that commonly affect “no heat” on this model

If you are troubleshooting heat on GLGQ2152EE3, these model-matched parts are often involved:

• Thermal limiter 137032600 (overheat protection that can open and stop heat)
• Dryer thermistor 134587700 (temperature sensing for heat control)
• Booster coil 5303931775 (gas valve coil kit that can prevent the valve from opening)

Why it matters

A “heating element” quote can be misleading on gas dryers; using the correct diagnosis prevents paying for the wrong part and helps restore safe, efficient drying. For model-specific checks and safety steps, follow the GLGQ2152EE3 installation guide and your use and care instructions.

Last updated: February 2026

On your Frigidaire dryer model GLGQ2152EE3, the model number is printed on the serial plate inside the door opening; you will see it on the left side of the door opening when the door is open. For the exact location diagram and how to record it, use the GLGQ2152EE3 owner's manual.

Where to look on the dryer

• Open the dryer door fully.
• Look along the left side of the door opening for a serial plate (label/metal tag).
• Find the line labeled Model or Model Number.
• Write down the full model number exactly as shown (letters and numbers).
• Record the serial number too; it helps match the correct parts list.

What the label typically includes

Label item	What it’s used for	Why you need it
Model number	Identifies the exact dryer design	Ensures parts fit GLGQ2152EE3
Serial number	Identifies production run	Helps confirm compatible revisions
Electrical/gas info	Ratings and requirements	Useful for installation and service

Why it matters

We use the model number to match the correct Frigidaire dryer parts (belt, drum bearing, thermistor, igniter) and to pull the right troubleshooting and wiring information. Even small model-number differences can change which replacement parts fit.

Last updated: February 2026