Kenmore Elite 66512763K310 dishwasher Parts

To identify your Kenmore dishwasher model, we look for the model/serial tag on the dishwasher itself, not the cabinet. On Kenmore Elite model 66512763K310, the tag is typically visible when you open the door and check the inner door frame (door jamb) or the tub rim near the front.

Where to find the model number tag

Check these common locations in this order:

• Open the door and inspect the left and right inner door frame (door jamb)
• Look along the top edge of the tub opening (upper rim)
• Check the side walls of the tub near the front (just inside the door)
• Wipe the area with a damp cloth; labels can look “missing” when they are just dirty
• Use a flashlight and view from an angle; faint printing shows up better

What the model number should look like

Kenmore dishwasher model numbers are usually a long string of numbers and letters. For this page, the correct format is:

Item	Example for this dishwasher	Why you need it
Model number	66512763K310	Ensures parts fit and diagrams match
Serial number	(varies)	Helps date the unit and confirm production run

Why it matters (parts and troubleshooting)

We use the model number to match the correct parts list, wiring, and installation details. Even small model-number differences can change the control panel, rack hardware, or water inlet valve.

If you are installing or leveling the dishwasher, the installation guide is the best reference for cabinet-opening checks, clearances, and securing the unit.

Quick tips if the label is hard to read

• Take a close-up photo and zoom in
• Try side lighting (flashlight from the left or right)
• Copy the full number exactly, including any suffix letters
• If the tag is damaged, compare your dishwasher’s features to the diagrams in the 66512763K310 owner’s manual

Last updated: January 2026

On the Kenmore Elite dishwasher model 66512763K310, a Start/Resume button that seems “dead” is usually caused by the door not latching fully, the door not being closed within 3 seconds after pressing Start/Resume, or a power/control issue. Follow the checks below in order.

Quick checks that fix most “won’t start” complaints

• Press Start/Resume, then close the door within 3 seconds; if you miss the window, the Start/Resume light can flash until you press it again.
• Make sure the door is closed tightly and latched (a loose latch prevents the cycle from starting).
• Check the home breaker/fuse and confirm the dishwasher has power.
• Confirm a cycle is actually selected (some models will not start if the cycle is not set correctly).
• Verify the water supply is turned on.

For the exact Start/Resume timing behavior and basic “does not operate” checks, use the 66512763K310 installation guide.

Reset the control (safe first step)

1. Turn off power at the breaker (or unplug if accessible) for about 5 minutes.
2. Restore power.
3. Select a short cycle and try Start/Resume again.

Why this matters

A reset clears a temporary control lockup after a power glitch or an interrupted cycle, and it avoids replacing parts unnecessarily.

If it still won’t start: what to inspect next

If the button lights but the dishwasher will not run, focus on the “start permission” chain: door latch, user interface, then control.

• Door latch/door switch: if the latch is worn or misaligned, the control will not allow a start.
• User interface/control panel: a failed keypad can make Start/Resume unresponsive.
• Electronic control board: if the board is not processing inputs, the dishwasher may not start.

Common symptoms vs. likely cause

What you see	Most likely issue	What to do
Start/Resume light flashes	Door not closed within 3 seconds	Press Start/Resume again; close door promptly
No response at all	No power or door not latched	Check breaker; latch door firmly
Buttons work but no cycle begins	Latch switch or control problem	Inspect latch; then control components

Related help for Kenmore dishwashers

If your model displays an error code or beeps in a pattern, use Kenmore 665 model dishwasher error codes to match the symptom to a specific failure area.

Last updated: January 2026

On Kenmore Elite dishwasher model 66512763K310, you can manually drain by canceling the active cycle so the dishwasher runs its built-in drain-out. Start any cycle, let it begin, then press Cancel/Drain (or Start/Cancel, depending on your console) to trigger the drain sequence.

Quick manual drain steps

• Press Start to begin a cycle (any wash cycle is fine).
• Wait 10 to 30 seconds so the dishwasher fills and the wash motor starts.
• Press Cancel/Drain (or Start/Cancel) once.
• Keep the door closed and allow the drain to run (often about 2 minutes).
• When the drain stops, open the door slowly and check the tub water level.

If it still will not drain

These checks cover the most common causes on Kenmore 665-series dishwashers.

• Air gap or sink drain blockage: Clear the air gap (if installed) and confirm the sink drains normally.
• Drain hose routing: Make sure the hose is not kinked and the connection is made before the drain trap and at least 20 in. above the floor.
• Garbage disposer plug: If the dishwasher drain connects to a disposer, confirm the disposer inlet knockout plug was removed.
• Drain pump issue: If you hear humming but no water moves, the drain pump may be jammed or failed.
• Inlet and fill problems: If the unit never fills correctly, it may not reach the point where it can drain normally.

Symptom	What it usually means	What to do next
Cancels but no drain sound	No power to drain pump or control issue	Check breaker, then review diagnostics in the 66512763K310 owner's manual
Drain sound but water remains	Partial blockage or weak pump	Inspect hose/air gap; consider the dishwasher drain pump WPW10531320
Drains into sink then backs up	Sink plumbing restriction	Clear sink trap/disposer and re-test

Why it matters

Standing water can cause odors, poor cleaning, and can overflow if the next cycle refills on top of a partial drain. A correct drain hose setup (including proper height and an air gap when required) prevents backflow into the tub.

Related help

• Use the Kenmore 665 model dishwasher error codes list if the control shows a fault or the dishwasher stops mid-cycle.
• For drain hose setup and routing details, follow the 66512763K310 installation guide.

Last updated: January 2026

Common problems we see on Kenmore dishwashers like model 66512763K310 are not draining, not starting, poor cleaning, leaking, and poor drying. Most of these trace back to a clogged drain path, a door that is not fully latched, a water supply issue, or a failed component such as a pump, inlet valve, or heater; confirm basics in the 66512763K310 installation guide.

Most common symptoms and what usually causes them

• Won’t start: door not closed and latched, cycle not set correctly, tripped breaker or blown fuse, water supply turned off
• Won’t fill: water supply off, restricted supply line, failed inlet valve
• Won’t drain: clogged drain hose or air gap, blocked sump area, failed drain pump
• Poor cleaning: blocked spray arm holes, overloaded racks, low water temperature, detergent issues
• Leaking: loose hose connections, damaged drain hose, sump seal issues
• Poor drying: heater problem, rinse aid issues, door opened too soon

Quick checks we recommend first (fast, no parts)

1. Verify the circuit breaker is on and the dishwasher has power.
2. Make sure the door is closed tightly and latched.
3. Confirm the cycle is set correctly and started.
4. Check the water supply valve is turned on.
5. If it starts but performance is poor, inspect racks and spray arms for obstructions.

Parts that commonly fix these issues on 66512763K310

Symptom	Common part involved	Example part for this model
Not draining	Drain pump or drain hose restriction	Dishwasher drain pump WPW10531320, dishwasher drain hose 8269144A
Not filling	Water inlet valve	Dishwasher water inlet valve W11175771
Not drying	Heater	Dishwasher heater W10703867
Leaking from bottom area	Sump and seal	Dishwasher sump and seal assembly WPW10455268

Why it matters

A dishwasher that does not fill, drain, or heat correctly can leave soil on dishes, extend cycle times, and strain components like the circulation system. Catching a simple cause (like a closed water valve or a kinked drain hose) prevents unnecessary part replacement.

Last updated: January 2026