Kenmore 79571022010 refrigerator Parts

On Kenmore refrigerator model 79571022010, you lower the front by turning the front leveling legs counterclockwise (and raise it by turning clockwise). Access the adjusters behind the base cover; the adjustment screw does not come out, it only changes height.

How to lower the front (step-by-step)

1. Open the freezer drawer and remove the screws holding the base cover, then remove the cover (see the 79571022010 owner's manual).
2. Use an 11/16-inch (18 mm) wrench or a flat-blade screwdriver on the leveling leg adjusters.
3. Turn the leveling legs counterclockwise to raise the front, or clockwise to lower the front.
4. Make small adjustments, then check door closing and cabinet stability.
5. Reinstall the base cover and tighten the screws.

Tips that make the adjustment easier

• Have someone gently push back on the top of the refrigerator to take weight off the leveling legs.
• Turn both leveling legs the same amount to keep the cabinet square.
• Keep the front slightly higher than the back so the doors close more easily.
• Do not put hands or tools into air vents or under the cabinet while it is plugged in.

Quick direction guide

What you want to do	Which way to turn the leveling leg	Result
Lower the front	Clockwise	Front goes down
Raise the front	Counterclockwise	Front goes up

Why it matters

Proper leveling helps the doors seal correctly, improves door closing, and reduces vibration. If the refrigerator is unsteady or the doors do not close smoothly, leveling is the first adjustment we recommend.

Last updated: January 2026

For Kenmore refrigerator model 79571022010, the correct water filter is the one specified for your exact model’s internal filter housing and indicator reset procedure. We match the filter by model number, then you install it and flush the system (about 2.5 gallons) after replacement; see the 79571022010 owner's manual.

How to identify the right filter for 79571022010

We use your model number to select the correct cartridge style and connection type (twist-in vs push-in), then confirm it matches your refrigerator’s “Filter (Inside)” location.

• Use the full model number 79571022010 (not a partial number)
• Check the filter location inside the fresh food compartment
• Match the cartridge shape and locking tabs to the existing filter
• Replace the filter at least every 6 months (more often with heavy use)
• After installing, flush the system before drinking or making ice

After you replace the filter: flush and reset

Your refrigerator’s water system needs to be flushed after a filter change, and the filter status light needs to be reset.

Step	What to do	Typical time/amount
Flush	Dispense water to clear air and carbon fines	About 2.5 gallons (about 5 minutes)
Reset	Press and hold the filter reset button	3 seconds
Verify flow	Check dispenser stream and ice production	First 24 hours

If water flow is weak after a new filter

A new filter can still have low flow if the supply pressure is low or a home filtration system is restricting water.

• Confirm the shutoff valve is fully open
• Make sure doors are fully closed (some models will not dispense with doors open)
• Check home water pressure; models with a filter typically need at least about 40 psi for good dispenser flow
• Avoid feeding the refrigerator from a reverse osmosis system if flow is poor
• If the filter is older than 6 months, replace it again (clogging reduces pressure)

Why it matters

Using the correct filter for Kenmore 79571022010 protects the water system, helps prevent slow dispensing, and keeps the filter indicator accurate after you reset it.

Last updated: January 2026

Water leaking from the filter area on your Kenmore refrigerator model 79571022010 is usually caused by an incorrectly seated filter, a damaged filter O-ring, or water pressure that is outside the recommended range. Reseating the filter and flushing the system after replacement often stops the leak; see the 79571022010 owner's manual.

Quick checks that fix most filter leaks

• Push and twist the filter fully into the housing until it locks (a partially engaged filter commonly drips).
• Remove the filter and inspect the O-rings for nicks, flattening, or debris; reinstall firmly.
• Flush the system after installing a new filter (the manual calls for flushing 2.5 gallons, about 5 minutes).
• Confirm your home water pressure is in range; the manual lists 30 to 100 psi.
• If you use a reverse osmosis system, expect lower pressure and more issues at the dispenser and filter connections.

What to do based on what you see

What you notice	Most likely cause	What we recommend
Drips immediately after a new filter install	Filter not fully seated or O-ring pinched	Remove, inspect O-rings, reinstall, then flush 2.5 gallons
Slow seep at the filter head/housing	Debris on seal surface or worn seal	Clean the sealing surface; replace the filter if seals are damaged
Leak happens when ice maker refills	Water hammer or pressure spikes	Have a plumber correct water hammer; verify pressure is 30 to 100 psi
Water won’t dispense and you see leaking	Restricted filter causing backpressure	Replace the filter; reset the filter indicator per the manual

Why it matters

A small filter leak can turn into cabinet or floor damage quickly, and it can also introduce air into the water line, causing sputtering at the dispenser and inconsistent ice maker fills.

When a part is likely involved

If the leak is not at the filter itself but at the rear connection or you see dripping near the supply line, the inlet valve or tubing connection may be the source. For this model, common water-system parts include the refrigerator water inlet valve MJX41178908 and refrigerator water tubing MJU62070602.

Last updated: January 2026

On Kenmore refrigerator model 79571022010, water leaking from the bottom is most often caused by defrost water not reaching the drain pan (a clogged or frozen defrost drain) or by a leak in the water supply system for the ice maker and dispenser. Start by checking for ice or debris at the drain path and then inspect the water line connections.

Quick checks we recommend first

• Look for a sheet of ice on the freezer floor or water under the crisper drawers (classic defrost drain issue).
• Check the drain pan area for overflow during/after a defrost cycle.
• Inspect the household water line and shutoff valve for slow drips.
• Check the tubing and fittings behind the refrigerator for moisture.
• If the leak happens only when dispensing water or making ice, focus on the inlet valve and tubing.

Most common causes (and what to do)

Likely cause	What you typically see	What to do next
Clogged/frozen defrost drain	Water pooling inside, then leaking out the bottom	Thaw ice with warm air, then flush the drain with warm water until it flows freely to the pan
Drain pan shifted or cracked	Water appears underneath even when no dispensing is used	Re-seat the pan; replace if damaged
Leaking water line connection	Drips behind unit; wet floor near back	Tighten compression nut slightly; re-check for drips
Water inlet valve seepage	Slow leak even when not dispensing	Inspect valve body and fittings; replace if leaking

Water line and valve leak checklist (ice maker and dispenser)

The 79571022010 manual emphasizes checking for drips at water line connections and tightening any leaking connections during setup and use. Use this checklist:

• Unplug the refrigerator before working behind it.
• Turn off the water supply at the shutoff valve.
• Dry all fittings, then turn water back on and watch for fresh drips.
• Confirm the tubing is routed so it does not vibrate against the cabinet or wall.
• If a fitting continues to seep after snugging, inspect the ferrule (sleeve) and tubing end for damage.

Helpful model-specific references: 79571022010 owner's manual, refrigerator water inlet valve MJX41178908, and refrigerator water tubing MJU62070602.

Why it matters

A small leak can turn into floor damage and can also lead to ice buildup, airflow problems, and warmer refrigerator temperatures if defrost water cannot drain correctly.

Last updated: January 2026