Kenmore 11071804000 gas dryer Parts

Your Kenmore dryer’s model number is printed on the model and serial number plate; for Kenmore model 11071804000, that plate is the official identifier we use to match the correct parts, wiring, and operating instructions. Record both the model and serial numbers for future service.

Most Kenmore dryers place the model and serial number plate in one of these common spots:

• Inside the dryer door opening (door jamb area)
• On the back panel of the dryer cabinet
• On the cabinet frame near the lint screen housing (varies by design)
• Occasionally behind a small access panel near the front opening

For model-specific guidance and what the plate looks like, use the 11071804000 owner's manual.

Write the model number exactly as shown, including all digits (no spaces). Then use it to select parts that fit your exact Kenmore gas dryer configuration.

• Model number: identifies the design family and parts fit
• Serial number: identifies the production run (helpful for service and revisions)
• Keep a photo of the plate on your phone for quick reference
• Use the full model number when ordering common wear items like a belt, door switch, or thermostat

Kenmore dryers can look similar across series, but parts can differ by model. Using the exact model number helps us match the correct components the first time, such as the dryer door switch WP3406107 or dryer drum belt 341241, and avoid returns due to fit issues.

Last updated: February 2026

For a Kenmore gas dryer like model 11071804000, you typically do not replace a “heating element” (that’s mainly an electric-dryer part). Heating repairs on this model usually involve the igniter, gas valve coils, sensors, or thermostats; total cost commonly runs $25 to $350, depending on the failed part and whether you hire service.

Here are realistic ranges we see for gas-dryer heat repairs.

• DIY parts-only: about $25 to $120 for common heat-related parts
• Service call + repair labor: about $150 to $350 total in many areas
• Higher totals happen when multiple parts are replaced during diagnosis (for example, coils plus a thermostat)

If the dryer runs but does not heat, these are frequent fixes for this Kenmore gas dryer.

• Igniter 279311 (lights the burner)
• Dryer gas valve coil kit 279834 (opens the gas valves after ignition)
• Dryer radiant sensor WP338906 (confirms flame/heat at the burner)
• Dryer operating thermostat WP3387134 (regulates drum temperature)
• Dryer high-limit thermostat W11050897 (safety cutoff if overheating occurs)

Gas-dryer “no heat” symptoms can be caused by airflow problems, safety cutoffs, or burner-assembly parts. Your 11071804000 owner's manual also emphasizes safe operation and proper venting; restricted venting can contribute to overheating and repeated thermostat failures.

• Clean the lint screen and confirm strong airflow at the outside vent hood
• Make sure the vent is not crushed or kinked behind the dryer
• Verify the cycle and temperature settings are on a heat-producing option
• If the dryer heats briefly then stops, suspect gas valve coils or a thermostat

Last updated: February 2026

On Kenmore dryer model 11071804000, the F40 code points to a control communication problem (a control is not “talking” correctly to another circuit), which can stop the dryer from running normally. We focus first on power resets, wiring connections, and heat related safety cutoffs.

• Unplug the dryer (or switch off the breaker) for 2 minutes, then restore power and try a cycle again.
• Confirm the door fully closes; a failed door switch can prevent normal operation.
• Check for a restricted vent (crushed, kinked, or clogged) because overheating can trigger safety devices.
• If the dryer starts but heat cuts in and out, suspect burner ignition components or thermostats.
• If the code returns immediately, inspect harness plugs at the main control area and motor area for a loose connection.

If your F40 shows up with no-start, intermittent running, or heat issues, these model-compatible parts are common suspects:

• Dryer door switch WP3406107
• Dryer high-limit thermostat W11050897
• Dryer operating thermostat WP3387134
• Dryer gas valve coil kit 279834

A communication fault often shows up when the dryer is stressed by heat or vibration. Fixing airflow (venting) and confirming safety thermostats are working helps prevent repeat shutdowns and protects key components.

Use the wiring diagram, troubleshooting steps, and any tech notes included in the 11071804000 owner’s manual.

Last updated: February 2026

If your Kenmore gas dryer model 11071804000 runs but produces no heat, or it will not run at all, a blown thermal fuse (or thermal cut-off) is a top suspect. The sure way to know is a continuity test with a multimeter after disconnecting power.

• Dryer tumbles but clothes stay cold and damp (no burner heat)
• Dryer will not start even though the outlet has power
• Heat stops mid-cycle and does not return until the failed safety part is replaced
• You recently had poor airflow (clogged lint screen or vent restriction)

1. Unplug the dryer (and shut off the gas supply valve for safety while servicing).
2. Access the thermal fuse or thermal cut-off on the blower housing or burner area (location varies by design); use the 11071804000 owner's manual for access guidance and safety notes.
3. Pull the wires off the fuse terminals.
4. Set a multimeter to continuity or lowest ohms.
5. Touch probes to the fuse terminals.

On this Kenmore gas dryer, these parts are often involved in heat complaints:

• Dryer high-limit thermostat W11050897 (safety cut-off kit)
• Dryer gas valve coil kit 279834 (burner coils that can fail when hot)
• Dryer operating thermostat WP3387134 (temperature regulation)
• Igniter 279311 (starts the burner ignition sequence)
• Dryer radiant sensor WP338906 (flame sensing)

A thermal fuse usually opens because the dryer overheated from restricted airflow. The manual’s troubleshooting guidance emphasizes checking the lint screen and verifying strong airflow at the outside exhaust hood; crushed or kinked venting can cause long dry times and overheating.

• Clean the lint screen before every load
• Inspect and clean the vent run and outside hood
• Replace crushed plastic or thin foil venting with heavy metal venting
• Keep the dryer level and avoid pushing it tight enough to kink the vent

Last updated: February 2026