Whirlpool WRS325SDHW05 refrigerator Parts

For the Whirlpool WRS325SDHW05, the most common service issues we see fall into three buckets: not cooling well (often airflow or defrost related), ice maker or dispenser problems (usually water supply or freezing), and unusual noises (often normal operation or a fan issue). Use the WRS325SDHW05 installation instructions and owner’s manual to match symptoms to the built-in troubleshooting steps.

Most common issues (and what to check first)

• Warm refrigerator or freezer: blocked air vents, doors not sealing, or dirty condenser area.
• Ice maker not making ice or small/hollow cubes: water pressure, kinked water line, or filter installation.
• Water dispenser slow: low water pressure, filter restriction, or inlet valve problem.
• Frost buildup: door not sealing or a defrost system problem.
• Noisy operation: buzzing/clicking from the water valve, fan whirring, or rattling from items on top.

Quick model-specific checks for WRS325SDHW05

The WRS325SDHW05 manual calls out several “first checks” that solve a lot of complaints without parts replacement:

• Allow 24 hours after a new install or major temperature change for full cooling.
• Keep air vents clear inside both compartments.
• Confirm doors close fully and gaskets are clean (sticky gaskets can cause poor sealing).
• If connected to water, verify household water pressure is in the typical operating range (the manual references 30 to 120 psi for dispenser/ice maker operation).

When a part is commonly involved

If basic checks do not help, these parts are often involved depending on the symptom:

Symptom	Commonly involved part	Example from this model’s parts list
No ice, slow fill, dispenser issues	Water inlet valve	Refrigerator water inlet valve WPW10179146
Warm temps, poor airflow, odd fan noise	Evaporator fan motor	Refrigerator evaporator fan motor WP2315549
Frost buildup, warming after a few days	Defrost heater	Refrigerator heater WP2323198

Why it matters

Catching the “common” causes early helps protect food safety, reduces energy use, and can prevent secondary damage (like ice buildup restricting airflow or water leaks from frozen lines).

Last updated: January 2026

Yes. On the Whirlpool WRS325SDHW05, we can safely replace many common, non-sealed-system parts ourselves (bins, shelves, door gaskets, switches, water filter components, and some fan parts) as long as we disconnect power first and follow the steps in the WRS325SDHW05 installation instructions and owner’s manual. Sealed-system repairs (refrigerant, compressor work) should be handled by a qualified technician.

Good DIY repairs vs. repairs to leave to a pro

DIY-friendly on WRS325SDHW05 (typical):

• Replacing the water filter and checking the filter door area
• Swapping door bins and shelves
• Replacing a door switch or light switch
• Replacing an evaporator fan motor (if you are comfortable removing panels)
• Replacing an ice container or dispenser-related mechanical parts

Usually not DIY (sealed system or specialized tools):

• Refrigerant leaks, charging, or any sealed-system tubing work
• Compressor replacement and related start components
• Filter drier replacement (sealed system)

Before you start (our quick safety checklist)

• Unplug the refrigerator or shut off power at the breaker.
• Turn off the water supply if you will open any water lines.
• Protect floors; this unit is heavy and can damage flooring when moved.
• Use the right tools; the manual lists common sizes (including TORX T30 for some door/hinge steps).
• Take photos as you disassemble so wiring and tubing go back correctly.

Parts we commonly replace on this model

What you’re fixing	Example compatible part for WRS325SDHW05	What it does
Water dispenser or ice maker not filling	Refrigerator water inlet valve WPW10179146	Opens to let water flow to the dispenser/ice maker
Dim or no interior light (switch issue)	Refrigerator light switch W11384469	Signals the control to turn lights on/off
Poor airflow or warm temps (fan issue)	Refrigerator evaporator fan motor WP2315549	Circulates cold air through the compartments
Leaking air, frost, or warm spots at door	Door gasket (black) 2159083	Seals the door to prevent warm air leaks

Why it matters

DIY repairs can save time and money, but the wrong repair can create water leaks, electrical hazards, or cooling problems. Using model-matched parts and the correct disassembly steps helps keep the WRS325SDHW05 running efficiently.

Last updated: January 2026

For your Whirlpool WRS325SDHW05 side-by-side refrigerator, the fastest way to find the correct part number is to first confirm the exact model number from the appliance ID tag, then use that model to match the part by name and diagram. Your WRS325SDHW05 installation instructions and owner’s manual also helps you identify key assemblies (like the water filter door and base grille) that affect which parts you need.

Where to find the model and serial tag (so you get the right part)

On WRS325SDHW05, the model and serial information is typically on an appliance label inside the fresh food compartment (often on a side wall near the crisper area) or on the cabinet frame near the door opening.

• Open the refrigerator door and check the inner side walls and door frame
• Look near the crisper drawers or lower cabinet liner
• If you cannot find it inside, check the back of the cabinet near the lower area
• Write down the full model number and serial number exactly as shown

How we recommend matching the correct part number

Once you have WRS325SDHW05, match parts using the part description and the model’s diagrams. This avoids ordering a similar-looking part that does not fit.

• Start with the symptom or the part name (example: “water inlet valve”)
• Confirm the part is listed for model WRS325SDHW05
• Compare the part name and any notes (color, location, revision)
• If the part connects to water or electrical, match it carefully before ordering

Common examples for this model

What you’re looking for	How it’s usually listed	Example part for WRS325SDHW05
Water supply control part	Water inlet valve	Refrigerator water inlet valve WPW10179146
Water filtration part	Refrigerator cartridge	Refrigerator cartridge EDR1RXD1
Ice storage bin	Ice container	Refrigerator ice container WPW10670845

Why it matters

Whirlpool part numbers can vary by revision, color, and dispenser configuration. Using the exact WRS325SDHW05 model number helps ensure the replacement part fits, seals correctly, and connects properly.

Last updated: January 2026

For your Whirlpool WRS325SDHW05 side-by-side refrigerator, order parts by matching the full model number first, then selecting the exact part ID shown for that model. This helps you avoid look-alike parts and improves the chance of getting the correct fit the first time.

Steps we recommend for ordering parts for WRS325SDHW05

• Confirm the model number on the rating label: WRS325SDHW05
• Identify the symptom and the system involved (cooling, ice maker, dispenser, door seal)
• Use the model-specific diagrams to find the exact part listing
• Match by part ID and part name, not just a photo
• Compare any numbers printed on your original part to the listing
• If you are ordering water-system parts, verify your home water supply meets the refrigerator requirements

Examples of parts listed for this model

These examples are shown in the parts list for WRS325SDHW05:

What you are fixing	Part listed for WRS325SDHW05	What it does
No water to dispenser/ice maker, slow fill	Refrigerator water inlet valve WPW10179146	Opens/closes to send water to the dispenser and ice maker
Ice bin cracked or missing	Refrigerator ice container WPW10670845	Stores ice and interfaces with the dispenser mechanism
Door not sealing well, warm air leaks	Door gasket (black) 2159083	Seals the door to prevent air leaks and frost

Water and fit checks before you buy

Your WRS325SDHW05 manual lists key setup requirements that can prevent unnecessary parts orders, including water pressure (30 to 120 psi) and basic troubleshooting. See the WRS325SDHW05 installation instructions and owner’s manual.

• If water dispenses slowly, test household water pressure and check for a kinked supply line
• If doors look uneven, leveling and alignment adjustments may solve it without parts
• If ice production is low after installation, allow time for full ice production and flush the water system

Why it matters

Ordering by the exact model number and part ID reduces returns and downtime, especially for water valves, ice storage parts, and door gaskets where small design differences can affect fit and sealing.

Last updated: January 2026