Kenmore Elite 79579752901 refrigerator Parts

Your refrigerator’s model is Kenmore 79579752901. To confirm it on the appliance, match that number to the model and serial tag, which is typically inside the fresh food compartment (side wall), inside the freezer, or behind the lower kickplate. Use the owner's manual for the exact label location and illustrations for this model.

Check these common spots on Kenmore bottom-mount refrigerators like model 79579752901:

• Inside the refrigerator compartment on a side wall near the crisper drawers
• On the inside wall of the freezer compartment
• Along the door frame area (open the door and look around the perimeter)
• Behind the lower kickplate or toe grille (front bottom)
• Behind the lower crisper drawer area (on the liner wall)

Model tags can be easy to misread. Use these tips so you capture the full model number:

• Write down the entire model number exactly as shown (all digits)
• Look for a separate serial number on the same tag
• Avoid mixing up similar characters (for example, 5 and S, 0 and O)
• Take a clear photo of the tag before ordering parts

We use the exact model number to match the correct parts and diagrams for your refrigerator. Even small model variations can change items like the water inlet valve, door switch, or freezer drawer hardware.

Last updated: February 2026

On a Kenmore Elite bottom-mount refrigerator like model 79579752901, the water filter is typically inside the fresh food (upper) compartment, often in the upper-right area or along the ceiling, behind a small cover or in a twist-in filter head. Use the owner's manual to confirm the exact spot for your configuration.

Most bottom-freezer refrigerators place the filter in one of these areas:

• Inside the refrigerator compartment, upper-right corner (behind a flip-down cover)
• Inside the refrigerator compartment, along the top ceiling near the front
• Inside the refrigerator compartment, left wall near the top shelf
• In the base grille at the bottom front (less common on many bottom-mount designs)

Before you start, we recommend turning off the ice maker and dispensing a little water to relieve pressure.

• Open the refrigerator (not the freezer drawer)
• Locate the filter cover or filter head
• If there is a cover, press the release tab or pull the cover open
• Twist the filter counterclockwise (or push and turn, depending on the style)
• Pull the filter straight out, then install the new one fully seated
• Run and discard several glasses of water to flush air and carbon fines

If you do not see a filter in the refrigerator compartment, your unit may use an inline filter in the water line instead of a cartridge in the cabinet.

Finding the correct filter location helps you replace it on schedule, maintain water flow to the dispenser and ice maker, and reduce strain on water components such as the lg refrigerator water inlet valve MJX41178908 and refrigerator water tubing MJU62070602.

Last updated: February 2026

A Kenmore Elite 79579752901 bottom-mount refrigerator typically lasts 10 to 15 years. In real-world use, units that get basic upkeep (clean condenser coils, good door seals, stable temperatures) are the ones that most often reach the upper end of that range. See the maintenance schedule in the owner's manual.

Most refrigerators fail early from heat stress, airflow problems, or sealed-system wear. These factors have the biggest impact:

• Condenser cleanliness: dust on the condenser coil makes the compressor run hotter and longer
• Door seal condition: air leaks cause longer run times and frost issues
• Room conditions: garages and hot kitchens shorten life by increasing run time
• Ice maker and water system health: leaks and valve issues can create secondary damage
• Defrost performance: repeated icing can strain fans and reduce cooling efficiency

These are the highest-value habits for the Kenmore 79579752901:

• Vacuum and brush the condenser area regularly
• Keep door gaskets clean and check for gaps
• Set stable temps (about 37°F fresh food, 0°F freezer)
• Replace clogged filters on schedule and flush the dispenser after changes
• Fix water leaks quickly; inspect tubing and connections

Once a refrigerator is past about 10 years, small efficiency losses (dirty coils, weak seals, slow fans) can add up to higher energy use and more frequent temperature swings. Preventive maintenance reduces compressor run time, which is the biggest driver of long-term reliability.

Last updated: February 2026

On the Kenmore Elite 79579752901 bottom-mount refrigerator, dH (or Er dH) indicates a defrost heating problem. Most often, the refrigerator is not sensing the defrost heater warming the evaporator as expected, so frost can build up and airflow can drop.

• Refrigerator section warming up even though the freezer still seems cold
• Frost or ice buildup on the rear freezer panel
• Reduced airflow from vents, weak cooling, or longer run times
• Fan noise changing as ice contacts the fan area
• Water leaking or puddles after a defrost cycle (ice melt cannot drain well)

1. Power reset: Unplug the refrigerator (or turn off the breaker) for 5 minutes, then restore power.
2. Check door closure: Make sure doors fully close and gaskets seal; warm air intrusion increases frost.
3. Look for heavy frost: If the freezer back wall is packed with frost, the defrost system needs attention.
4. Clear the drain path: If you see water under drawers, inspect the drain area; a clogged drain can refreeze.
5. Confirm airflow: Do not block vents with food packages.

If the code returns after a reset, these parts are the usual suspects for this model family:

A defrost heating fault lets frost build up on the evaporator coil. That blocks airflow, so the refrigerator compartment warms first, food spoils faster, and the compressor can run longer than normal.

For the exact error-code behavior, test points, and access steps for the Kenmore Elite 79579752901, use the owner's manual. If you also see other codes, our Kenmore 795 model bottom freezer refrigerator error codes guide helps you match symptoms to the right checks.

Last updated: February 2026

Common problems on the Kenmore Elite refrigerator model 79579752901 include warm temperatures (fresh food or freezer), water leaking inside or under the unit, ice maker or dispenser issues, and unusual noises. Most fixes start with airflow and defrost checks, then move to testing fans, sensors, and water components using the owner's manual.

• Not cooling or weak cooling: dirty condenser coil, failed evaporator fan, failed condenser fan, or a defrost failure causing frost buildup
• Freezer cold but refrigerator warm: restricted airflow (ice buildup), evaporator fan issue, or air duct blockage
• Water leaking or puddles: clogged/iced drain system, cracked drain tube, or leaking water line
• Ice maker not making ice: low water supply, inlet valve problem, frozen fill tube, or ice maker failure
• Lights not working or door alarm issues: door switch or light board problem
• Noisy operation: fan motor noise, fan blade rubbing ice, or vibration from the cabinet/lines

1. Confirm temperatures: set refrigerator to about 37°F and freezer to about 0°F, then allow 24 hours to stabilize.
2. Check airflow: make sure vents are not blocked by food packages.
3. Inspect for frost: heavy frost on the rear freezer panel points to a defrost system issue.
4. Clean the condenser area: dust buildup reduces cooling and increases run time.
5. Listen for fans: you should typically hear a fan running when the compressor is running.

Cooling, defrost, and water-delivery problems can cascade. For example, a failed evaporator fan can cause warm temperatures and spoilage, while a clogged drain can create ice buildup that blocks airflow and mimics a cooling failure.

If your display shows an error, use our Kenmore 795 model bottom freezer refrigerator error codes guide to narrow the problem to a sensor, fan, defrost circuit, or control-related issue.

Last updated: February 2026