Kenmore 11024902200 washer Parts

Kenmore 110-series washers do not all have the same tub capacity; the cubic feet varies by the exact model. For Kenmore model 11024902200, the most reliable way to confirm capacity is to check the specifications section in the 11024902200 owner's manual.

When customers ask about “110 series,” they are usually referring to multiple generations of Kenmore top-load designs. Most fall into these common ranges:

• Standard top-load (older, deep tub): about 3.0 to 3.5 cu. ft.
• Larger-capacity top-load: about 3.6 to 4.3 cu. ft.
• Compact/space-saving units: often under 3.0 cu. ft.

Use these quick checks to get the correct number for your washer:

• Look in the specifications/features pages of the 11024902200 owner's manual
• Check the model and serial plate location noted in the manual (commonly under the lid area)
• If you are comparing to a replacement, match by model number first, then compare dimensions and features

Capacity affects how much laundry you can wash per load, how much water the washer uses at each water level setting, and whether bulky items (comforters, jackets) can agitate and spin correctly without out-of-balance problems.

Last updated: January 2026

A Kenmore washer typically lasts 10 to 15 years. For the Kenmore 11024902200 top-load washer, lifespan depends most on load size, leveling, water quality, and routine care; following the maintenance guidance in the 11024902200 owner's manual helps you reach the higher end of that range.

Most Kenmore washers fall into these real-world averages:

We see these conditions reduce washer life more than any single part failure:

• Consistently overloading the basket (extra strain on drive and suspension)
• Running unbalanced loads (shakes, walks, and wears the drive system)
• Installing on an unlevel or soft floor (the install guide calls for a level floor and sturdy support)
• Using too much detergent (residue buildup, poor draining, odors)
• Ignoring early symptoms (slow drain, no spin, burning smell, loud grinding)

On the Kenmore 11024902200, these are frequent wear items when agitation or spinning performance drops:

• Agitator dog 80040 (worn dogs can cause weak or no agitation)
• Washer lid switch WP3949238 (a failed switch can stop spin or drain on many top-load designs)
• Washer drain pump WP3363394 (clogs or wear can cause slow or no draining)
• Washer motor coupling 285753A (can fail after heavy loads or repeated stalls)

Replacing a small wear part early can prevent secondary damage. For example, repeated unbalanced spinning can stress the clutch, gear case, suspension, and basket support, turning a simple fix into a larger repair.

Last updated: January 2026

For a hard reset on your Kenmore washer model 11024902200, unplug the washer (or switch off the breaker) for 2 minutes, then restore power and run a normal cycle. This clears many temporary control glitches and can stop false error behavior.

• Turn the washer OFF.
• Unplug the power cord (or turn the circuit breaker OFF).
• Wait 2 minutes.
• Restore power.
• Set a Rinse/Spin or Normal cycle and press Start.
• If the washer was moved recently, confirm it is level to prevent vibration-related issues.

A “reset” will not fix a failed safety switch or a drain problem. These quick checks often pinpoint the real cause:

• Confirm the lid closes fully and the lid strike lines up; a failed washer lid switch WP3949238 can stop spin.
• If the tub is full of water, check for a clog or a weak pump; the washer drain pump WP3363394 is a common fix.
• If the motor runs but the washer will not agitate or spin, inspect the washer motor coupling 285753A.
• If agitation is weak or the agitator slips, check the agitator dog 80040.

A hard reset is the fastest first step because it restores the control to a clean power-up state. If symptoms return immediately, we treat it as a parts or installation issue, not a control “memory” problem.

For model-specific operating steps and cycle behavior, use the 11024902200 owner’s manual.

Last updated: January 2026

For Kenmore washer model 11024902200, we unclog the drain hose by unplugging the washer, draining any standing water, then disconnecting and flushing the hose to remove lint, coins, or small clothing items. Reinstall the hose correctly so it will not kink, leak, or siphon.

• Unplug the washer.
• Turn off both water faucets.
• Keep towels and a shallow pan ready for spills.
• Pull the washer forward to access the drain connection.

1. Check routing first: straighten the hose and rotate the hooked end to remove kinks.
2. Disconnect the hose from the standpipe/laundry tub.
3. Remove the hose at the washer outlet (bottom connection) and catch any remaining water.
4. Flush the hose with running water; if blocked, gently work the clog out with a flexible drain snake.
5. Reinstall using the clamp and seating method in the 11024902200 installation guide.

The installation guide steps matter because they keep the hose sealed and properly vented:

• Wet the inside of the straight hose end with tap water only.
• Position the clamp about 1/4 inch (6 mm) from the end.
• Push and twist the hose fully on until it hits the cabinet stop.
• Keep the hooked end; do not force extra hose deep into the standpipe.

A clear, correctly installed drain hose prevents floor leaks and helps stop dirty water from flowing back into the washer, which can cause odors and poor rinsing.

Last updated: January 2026