Kenmore 66512413N410 dishwasher Parts

Common problems we see with the Kenmore 66512413N410 dishwasher include not starting, poor cleaning, poor draining, and drying issues. Many symptoms trace back to loading, water temperature (120°F), filters, door latch, or a drain restriction; the 66512413N410 user manual troubleshooting table is the fastest way to narrow it down.

• Won’t start or stops mid-cycle: door not fully latched, Start/Resume sequence not completed, Control/Lock enabled, or power issue
• Detergent left in the dispenser: blocked spray path from large dishes, low water temperature, or cycle interruption
• Cloudy or spotted dishes: hard water, not enough rinse aid, incorrect detergent amount, or water below 120°F
• Not draining: kinked/clogged drain hose, blocked air gap, or a failing drain pump
• Burning smell: plastic contacting the heating element, debris on the heater, or a component overheating

1. Close the door firmly; if the Start/Resume light blinks, press START/RESUME and close the door within 3 seconds.
2. Confirm hot water supply; incoming water should be about 120°F (49°C).
3. Clean the filter area and remove any food debris from the sump.
4. Check the drain path: disposer knockout (if applicable), air gap, and hose routing.
5. Reload to prevent spray arm blockage (avoid large pans at the back interfering with the wash system).

Catching the root cause early prevents repeat wash failures, protects dishes from damage due to improper loading, and helps avoid overheating conditions (especially around the heating element and venting).

Last updated: January 2026

On Kenmore dishwasher model 66512413N410, the removable filters are located at the bottom center of the tub, directly under the lower rack. You access them from inside the dishwasher by pulling out the lower rack and lifting out the filter assembly in the sump area.

• Pull the lower dishrack all the way out and set it aside.
• Look for the round filter assembly in the bottom center of the tub.
• Turn the upper filter assembly about 1/4 turn counterclockwise to unlock it, then lift it out.
• Lift the lower filter slightly and pull it forward to remove.
• Rinse both pieces under running water; use a soft brush for stuck-on soil.

This dishwasher uses two removable filter pieces that work together.

• Set the lower filter back under the locating tabs so the round opening lines up.
• Insert the upper filter assembly into the lower filter opening.
• Rotate the upper filter clockwise until it drops and locks; it should not spin freely.

A clean, properly locked filter helps maintain strong wash performance, protects the pump, and reduces gritty residue on dishes. We recommend checking the filter about monthly, and more often if you wash heavy-soil loads.

For model-specific diagrams and the filter section, use the 66512413N410 owner's manual.

Last updated: January 2026

Kenmore dishwasher model 66512413N410 is a standard built-in dishwasher sized for a 24-inch cabinet opening, with an installation height that adjusts at the leveling legs. The installation specs call out a cabinet opening height range of 33 1/2 inches to 34 1/2 inches (with a lower option when rear legs/spacers are removed); use the 66512413N410 installation guide for the exact height adjustment chart and cutout requirements.

These are the measurements that matter most for fit and hookup routing:

• Cabinet opening width: standard 24 inches (built-in opening)
• Cabinet opening height: 33 1/2 to 34 1/2 inches adjustable (leveling legs)
• Tight-height option: fits 33 1/2 inches opening when rear leveling legs/spacers are removed (per install notes)
• Depth planning: allow space behind the unit for the drain hose, water line, and power cord

• Measure height at the lowest point under the countertop, not the front edge only.
• Measure width at the narrowest point between cabinets.
• Check for obstructions (valves, electrical box, drain connection) that reduce usable space.

Correct sizing prevents a dishwasher that will not slide in, a door that rubs the cabinet, or a unit that cannot be leveled. Proper clearance also protects the drain hose and water inlet line from kinks and leaks.

To confirm all cutout and connection requirements for your kitchen, match your measurements to the 66512413N410 installation guide and the 66512413N410 owner’s manual.

Last updated: January 2026

For Kenmore dishwasher model 66512413N410, the most reliable “hard reset” is to cancel the current cycle, let the unit drain, then start a fresh cycle. This clears a stuck program and reinitializes the control for the next wash; follow the control steps in the 66512413N410 owner's manual.

• Open the door slightly to pause the cycle; wait for spraying to stop.
• Use the dishwasher’s Cancel/Drain function to cancel the cycle and drain water.
• Close the door so the drain can run.
• Wait until draining finishes and the dishwasher is idle.
• Select a new cycle and options.
• Press START/RESUME to begin.

• Control Lock is on: turn off Control Lock using the procedure listed in the 66512413N410 owner's manual.
• Door not fully latched: close the door firmly; if it will not latch consistently, inspect the dishwasher door latch WPW10653840.
• Power glitch: turn off the breaker (or unplug if accessible) for 1 minute, then restore power.
• Standing water remains: check the drain path for kinks or clogs; a weak drain can point to a failing dishwasher drain pump WPW10348269.

Canceling and draining resets the cycle state and removes leftover water, which helps prevent “won’t start” symptoms, odor, and incomplete washes caused by a hung cycle.

Last updated: January 2026