Installation guide
Owner’s manual
Error Codes
How to fix F12 error code on stove?
On the Frigidaire FCRC3012ABA electric range, an F12-type fault is cleared by stopping the current cycle, then doing a full power reset. If the code returns after the reset, focus troubleshooting on the cooktop or oven circuit involved (control, wiring, or a failed component).
- Press OFF/CANCEL to clear the code.
- Turn power off at the breaker for 5 minutes.
- Restore power, then set the clock.
- Try Bake or Broil again.
- If the code returns immediately, stop using the affected function and move to checks below.
For the exact key sequence and any model-specific notes, follow the troubleshooting section in the FCRC3012ABA owner's manual.
Many F or E codes point to a detected fault condition. These checks help narrow it down:
- Loose or burned wiring connections at the terminal block, control, or element leads.
- Cooktop element circuit issues (infinite switch, element, or wiring).
- Oven temperature sensing issues that can cause abnormal heating behavior.
- Heating element damage (blistering, breaks, or arcing marks).
- Control problem if all wiring and loads test good.
| Symptom you notice | Most likely area | Example part for FCRC3012ABA |
|---|---|---|
| Oven will not bake, or heats erratically | Bake circuit | Frigidaire range bake element 316075103 |
| Oven temperature seems inaccurate | Sensor circuit | Frigidaire range oven temperature sensor 316490000 |
| One surface burner will not regulate heat | Surface control | Frigidaire range surface element control switch 316436001 |
An F-code is the range telling you it detected an unsafe or out-of-range condition. Clearing it without addressing a loose connection or failing element can lead to repeated shutdowns, poor cooking performance, or overheated wiring.
- Turn off power at the breaker before removing panels or touching wiring.
- If you see melted wires, a burning smell, or arcing marks, keep the breaker off and have the range serviced.
Last updated: January 2026
How do I reset my Frigidaire electric range?
To reset your Frigidaire electric range model FCRC3012ABA, we recommend doing a power reset: turn the range off, shut off power at the breaker (or unplug it), wait about 30 seconds, then restore power. This clears many control glitches and restores normal operation.
- Turn all surface burner knobs to OFF.
- If plugged in: unplug the range.
- If hardwired: switch the range breaker OFF (typically a 240V double-pole breaker).
- Wait 30 seconds.
- Restore power, then set the clock and test Bake and a surface element.
A “reset” will not fix a power supply problem. If the range was recently installed or moved, focus on the power connection and terminal block wiring shown in the FCRC3012ABA installation guide.
Common signs of a supply or connection issue:
- Display lights up, but no heat from bake, broil, or surface elements
- Only some elements heat, or heat is weak
- Heat works intermittently when the cord is bumped
- Confirm the breaker is fully ON (flip OFF then ON).
- Verify the outlet is a proper range receptacle and cord is seated.
- Inspect the rear terminal block area for loose connections (power off first).
- Make sure the factory-installed terminal block nuts were not loosened during installation.
| Symptom | Most likely cause | Best next step |
|---|---|---|
| Control panel works, nothing heats | Missing L1 or L2 (240V supply issue) | Check breaker, cord, terminal block wiring |
| Oven heats, burners do not (or vice versa) | Wiring issue or failed control component | Test circuits per manual troubleshooting |
| Oven temperature is erratic | Sensor or heating circuit problem | Check sensor and elements |
If power supply is correct and the range still will not heat, these model-compatible parts are common suspects:
- Range bake element 316075103 (bake not heating)
- Range broil element 316203200 (broil not heating)
- Range oven temperature sensor 316490000 (temperature issues, overheating, underheating)
A reset clears electronic control glitches, but heating on an electric range depends on a solid 240V supply (L1 and L2) and tight terminal block connections. A partial power loss can leave lights working while heating stops.
Last updated: January 2026
How to fix F3 error code Frigidaire oven?
On the Frigidaire FCRC3012ABA electric range, an F3 error points to an oven temperature sensing problem (most often the oven temperature sensor circuit). Start by clearing the code with OFF, then do a short power reset; if the code returns, focus troubleshooting on the sensor and its wiring.
- Press OFF to clear the fault code.
- Turn power off at the breaker (or unplug if accessible) for 5 minutes, then restore power.
- Set the clock after power is restored (the oven may not operate until time of day is set).
- Try Bake again and watch for the code to reappear.
If F3 comes back after the reset, we recommend checking these items in order:
- Loose or damaged sensor connector at the back of the oven cavity.
- Pinched, burned, or broken wiring between the sensor and control.
- Failed oven temperature sensor.
- Control issue (less common) if sensor and wiring test good.
A common repair for an F3-type temperature fault is replacing the oven temperature sensor: Frigidaire range oven temperature sensor 316490000.
| What you see | What it usually means | What we do next |
|---|---|---|
| F3 appears immediately after starting Bake | Sensor circuit is open/shorted | Inspect connector and wiring, then test sensor |
| Oven heats erratically, then F3 appears | Sensor drifting or intermittent connection | Reseat connector, check harness routing |
| F3 returns after reset every time | Hard failure in sensor circuit | Replace sensor or repair wiring |
The oven control uses the temperature sensor to regulate heat. When the sensor signal is out of range, the control may stop heating and post an F or E code to prevent overheating or unsafe operation.
For the exact key sequence to clear fault codes and the recommended power-reset procedure, follow the troubleshooting section in the FCRC3012ABA owner’s manual.
Last updated: January 2026
How to fix F022 error Frigidaire oven?
On the Frigidaire FCRC3012ABA electric range, treat an F022 as an electronic control fault that you clear first, then reset power. If the code returns after a proper reset, the next step is checking power and wiring connections to the control system.
- Press OFF to clear the code.
- Turn off power at the breaker.
- Wait 5 minutes.
- Restore power.
- Set the clock (some functions will not run until time-of-day is set).
- Try Bake or Broil again.
These steps match the control-fault reset procedure in the FCRC3012ABA owner's manual.
A repeating code after a full power reset points to a persistent electrical issue such as a loose connection, damaged wiring, or a failing control component.
- Check the range has steady power (no flickering display or random beeping).
- Inspect for pinched or burned wires (often after moving the range).
- Verify the main power connections are tight and not heat-damaged.
| What happens after reset | What it usually means | What to do next |
|---|---|---|
| Code clears and does not return | Temporary control glitch | Keep using; monitor for repeat |
| Code returns immediately | Ongoing electrical/control problem | Inspect wiring and power connections |
| Oven will not run and clock will not set | Power supply issue | Check breaker, cord, and terminal connections |
If you find loose or overheated power connections, these parts are commonly involved:
- Range terminal block 5303935271 (main power connection point where overheating or looseness can cause control problems)
- Harness,wiring ,main 5304520708 (wiring harness that can be damaged or have loose connectors)
Repeated control fault codes can interrupt baking or broiling and can indicate overheating or loose electrical connections. Correcting the underlying power or wiring issue helps prevent repeat shutdowns.
Last updated: January 2026
