Kenmore 10658039800 side-by-side refrigerator Parts

To reset your Kenmore 10658039800 side-by-side refrigerator, we recommend a simple power reset: turn the temperature control OFF, disconnect power for about 5 minutes, then restore power and set the control back to your normal setting. This clears most control glitches.

• Turn the Temperature Control (or Refrigerator/Freezer Control) to OFF.
• Unplug the refrigerator (or switch OFF the circuit breaker).
• Wait 5 minutes.
• Plug back in (or switch the breaker ON).
• Set the control back to the desired temperature setting (see 10658039800 owner's manual).

Some issues are not fixed by a power reset alone. Use this quick guide to choose the next step.

If the reset helps only briefly, a component may be failing.

• Refrigerator inlet valve W10408179 (controls water flow to ice maker and dispenser)
• Refrigerator ice maker 2198597 (ice production assembly)
• Refrigerator defrost heater WP2323198 (melts frost off the evaporator)
• Refrigerator bi-metal thermostat WPW10225581 (helps control defrost cycling)
• Refrigerator evaporator fan motor WP2315549 (moves cold air through compartments)

A reset restores normal control operation, but it does not fix airflow restrictions, water supply problems, or failed parts. Using the correct next step prevents food-temperature issues and repeat shutdowns.

Last updated: February 2026

For Kenmore model 10658039800, the model number is printed on a rating label inside the refrigerator cabinet. Common spots include the inside wall of the fresh food section or freezer, inside the door area, behind the lower crisper drawer, or behind the base (kick) plate; confirm the exact location in the 10658039800 owner's manual.

Check these locations in order (most common first):

• Inside the fresh food compartment on a side wall (near the top or mid-level)
• Inside the freezer compartment on a side wall
• On the inside edge of the refrigerator door or freezer door
• Behind or just above the lower crisper drawers (label on the back wall)
• Behind the base grille or kick plate at the bottom front

We recommend copying the information exactly as printed so you can match Kenmore parts correctly.

• Write the model number exactly, including all digits
• Take a clear photo of the label before it fades
• Use the model number when selecting parts like an ice maker, water inlet valve, or door cam
• If the label is behind the kick plate, unplug the refrigerator before removing panels

Kenmore refrigerators can look identical across multiple model numbers, but internal components (like the ice maker, defrost heater, or temperature control) can differ. Using the exact model number helps us match the correct replacement parts and diagrams the first time.

Last updated: February 2026

On Kenmore side-by-side refrigerator model 10658039800, the water filter is in the base grille below the freezer door. Press the eject button, pull the filter straight out, move the cap to the new filter, then push the new filter in until the eject button pops back out (fully seated). See the 10658039800 owner's manual.

• Press the eject button and pull the filter straight out by the cap.
• Turn the filter cap counterclockwise to remove it from the old filter.
• Remove the protective cover from the new filter O-rings.
• Install the cap on the new filter; align the ridge and arrow, then turn clockwise until it snaps.
• Push the new filter into the base grille opening until the eject button pops out.
• Tug gently on the cap to confirm the filter is locked in place.

After you install the new filter, flush air out of the lines:

• Hold the dispenser lever 5 seconds on, then release 5 seconds off.
• Repeat until water starts flowing.
• Continue the 5-on/5-off cycle for 2 more minutes.

A properly seated filter helps maintain normal water flow to the dispenser and ice maker, and flushing prevents sputtering and cloudy water caused by trapped air.

The filter cap is a separate piece on this model; if yours is cracked or won’t stay attached, replace the refrigerator water filter cap (black) WP2260518B.

Last updated: February 2026

Most Kenmore side-by-side refrigerators are about 36 inches wide; for Kenmore model 10658039800, the minimum cabinet cut-out width is 36 inches (91.44 cm) for installation. For exact clearance and door-swing needs, follow the spacing guidance in the 10658039800 owner's manual.

A 36-inch width is the typical cabinet opening needed so the refrigerator can slide in and ventilate properly. Your actual space planning should also include side clearance for doors and drawers.

• Plan for a 36-inch cabinet opening as the baseline.
• Allow 1/2 inch of space on each side and at the top for ventilation.
• If installed next to a fixed wall, leave at least 2 inches on the hinge side (depending on setup) so doors can swing open.
• If the unit has an ice maker, leave extra room behind for the water line.
• If you want to remove crisper pans when the refrigerator is against an extended wall, a 54-inch total cabinet opening is recommended (36 inches plus an additional 18 inches).

If the opening is too tight, you can end up with poor airflow (warm temperatures), doors that do not open fully, and drawers (like crispers) that cannot slide out for cleaning or service.

Last updated: February 2026

Your Kenmore side-by-side refrigerator model 10658039800 has an approximate total capacity of 21.9 cubic feet. This is the overall storage volume for both the fresh food and freezer compartments combined; it helps you compare size, storage space, and replacement options.

We recommend checking the model-specific documentation because capacity can vary slightly by version, shelving, and bin configuration.

• Look for “capacity,” “total volume,” or “specifications” in the 10658039800 owner's manual
• Compare the listed capacity to the cabinet cutout guidance if you are planning a replacement
• Use the model number 10658039800 when ordering parts or looking up specs

Capacity affects how the refrigerator performs in real use and how well it fits your household needs.

• Food storage planning: helps estimate weekly grocery capacity
• Energy and airflow: overpacking can restrict airflow and cause warm spots
• Replacement shopping: lets you compare like-for-like sizes across brands

If you are measuring for a new unit or re-installing this one, the manual also calls out typical clearance needs (for ventilation and door swing). Those clearances matter as much as cubic feet when you are checking fit.

Last updated: February 2026

Most Kenmore refrigerators average 10 to 15 years of service life. For a Kenmore 10658039800 side-by-side refrigerator, lifespan depends most on routine care (cleaning, airflow, and door sealing) and fixing cooling or ice and water issues early using the 10658039800 owner's manual.

Kenmore refrigerators span several designs and manufacturers, so we use the industry-typical range for full-size refrigerators.

These steps reduce compressor run time, prevent overheating, and help the sealed system stay healthy.

• Clean dust from the condenser area regularly (more often with pets).
• Keep door gaskets clean and sealing flat; fix gaps quickly.
• Set stable temps (about 37°F fresh food, 0°F freezer).
• Leave space for airflow around the cabinet and base grille.
• Replace water filters on schedule to protect the water system.
• Address frost buildup early; it strains the evaporator fan and cooling performance.

Catching these early often turns a “replacement” situation into a straightforward repair.

• Food temps swing or the unit runs constantly
• Loud clicking/humming, frequent cycling, or warm cabinet sides
• Heavy frost on the freezer back wall (defrost system issue)
• Ice maker slows or stops, or water dispenser flow drops
• Water leaks or puddles under the refrigerator

A refrigerator that is running hot, leaking, or struggling to hold temperature wears out expensive components faster (especially the compressor and evaporator fan motor). Following the cleaning and troubleshooting guidance in the manual helps you get the full expected lifespan.

Last updated: February 2026