Kenmore 66513482K901 undercounter dishwasher Parts

Yes. You can still get replacement parts for a Kenmore dishwasher, and for model 66513482K901 many common repair parts are still available, such as drain components, seals, and electrical parts. The key is matching parts to your exact model number and following the wiring and installation guidance in the 66513482K901 installation guide.

How to make sure you order the right part

Kenmore dishwashers are often built with widely used components, so the correct match comes down to the model number and the symptom.

• Confirm the model number is 66513482K901 (use the full number, including the suffix)
• Match the symptom (leaking, not draining, not heating, no power) to the most likely part
• Compare your existing part markings to the replacement listing (when accessible)
• Use the wiring/grounding instructions before any electrical repair
• After installing a part, run a short cycle and check for proper fill and drain

Common parts people still replace on this model

Here are examples of parts that are commonly replaced on Kenmore 66513482K901 dishwashers.

Symptom	Likely part to check	Example part for this model
Water left in tub	Drain pump, drain hose, air gap	Dishwasher drain pump WPW10348269
Dishes not drying, water not heating	Heating circuit	Dishwasher heating element W10518394
No power or dead control	Fuse, wiring, control	Fuse W10258275
Leaks at the door	Door seal	Dishwasher door seal W10542314

Why it matters

Ordering by the exact model number helps you avoid returns and downtime. It also helps you install parts safely; the installation instructions emphasize proper grounding and avoiding extension cords, which is especially important when replacing electrical parts.

Last updated: February 2026

Your Kenmore dishwasher model number is printed on the model and serial number label inside the door area. On Kenmore models like 66513482K901, we typically see the label on the inner door frame, along the top edge of the door opening, or on the tub wall just inside the door.

Where to look first (fastest checks)

• Open the dishwasher door fully and look along the inner door frame.
• Check the top edge of the door opening.
• Look on the tub wall just inside the door (the manual shows a dedicated model/serial label location).
• Wipe the area with a damp cloth; grease and detergent film can hide the print.
• Use a flashlight and look from an angle; the label is often reflective.

What the model number looks like

For Kenmore dishwashers, the model number is usually a long string of letters and numbers. Many Kenmore units also include a prefix like 665 (as in 66513482K901).

What you see on the label	What it means	Why you need it
Model number (example: 66513482K901)	Exact dishwasher version	Ensures parts fit and diagrams match
Serial number	Production identifier	Helps with service history and dating

If you cannot find the label inside the door

If the label is missing or unreadable, we use these next-best options:

• Check for a second label on the side of the inner door.
• Look near the lower edge of the tub opening.
• Review the paperwork that came with the unit, or use the 66513482K901 owner’s manual to confirm label placement and dishwasher features.

Why it matters

Kenmore dishwashers can look similar across multiple versions, but parts like a heating element, drain pump, or control board can vary by model. Using the exact model number helps us match the correct diagrams and compatible replacement parts the first time.

Last updated: February 2026

Yes, repairing a Kenmore dishwasher model 66513482K901 is usually worth it when the problem is a wear item (seal, hose, fuse) or a single failed component; repairs often cost far less than replacement and can restore years of dependable operation (see the 66513482K901 owner's manual).

Quick way to decide (cost, age, and what failed)

Use these practical checkpoints before you buy parts or schedule service:

• If the dishwasher is under ~10 years old, repairs are typically the better value.
• If the repair is under ~50% of replacement cost, repairing is usually the smart move.
• If it’s a leak, no-heat, or no-drain issue, it’s often a straightforward fix.
• If the tub is damaged or multiple major parts have failed, replacement is often the better long-term choice.
• If you can DIY safely, you save the most on labor (power off at the breaker first).

Common repairs on 66513482K901 that are often worth it

These are frequent, fixable failures on dishwashers like this Kenmore model:

Symptom	Often worth repairing?	Likely area to check
Not drying well	Yes	Heating circuit, rinse aid use, loading
Won’t drain	Yes	Drain path, drain hose, drain pump
Leaking at the door	Yes	Door seal alignment/condition
Dead/no power	Often	Fuse, wiring, control issues
Loud grinding/buzzing	Often	Hard object in wash module; persistent noise needs service

If you’re troubleshooting a “no heat” or poor drying complaint, the dishwasher heating element W10518394 is a common repair part to evaluate.

What the manual says that affects the decision

The manual emphasizes maintenance and troubleshooting steps that can prevent unnecessary part replacement:

• Check loading so water drains properly; do not overload.
• Use liquid rinse aid to improve drying.
• If draining is poor, check and clean the drain air gap (when installed).
• Persistent grinding/buzzing after a full cycle points to a service-level issue.

For installation-related drain and air gap requirements, follow the 66513482K901 installation guide.

Why it matters

A targeted repair (like a seal, hose, fuse, or heating issue) usually restores performance quickly and avoids the higher cost and hassle of replacing an undercounter dishwasher.

Last updated: February 2026