Kenmore Elite 79641582410 washer Parts

Yes, repairing a Kenmore Elite washer like model 79641582410 is worth it when the fix restores reliable operation for less than the cost of replacement, especially for common, repairable failures such as draining, filling, or door-lock problems. Use the 79641582410 owner's manual to match symptoms to the right repair path.

When repair is the smart choice

Repair usually makes sense when the washer is otherwise in good condition and the problem is isolated to a serviceable part.

• The washer completes cycles but has one clear failure (won’t drain, won’t fill, won’t lock)
• No major rust, cabinet damage, or repeated flooding issues
• The tub and basket are quiet and stable during spin (no severe banging or grinding)
• The repair is a single-part replacement plus basic labor
• You can confirm the symptom with simple checks (filter, hoses, power reset)

High-value repairs for this model

These are common front-load washer repairs that often bring the machine back to normal operation.

Symptom	Likely system	Example part to check/replace
Won’t drain, slow drain, standing water	Drain system	Drain pump motor (4681EA2001T) - washer part by lg electronics 4681EA2001T
Won’t fill or fills slowly	Water inlet	Lg washer single-solenoid water inlet valve 5220FR2006H
Door won’t lock or won’t start	Door lock/strike	Lg washer door lock EBF61315802

Quick checks before you spend money

The manual calls out routine maintenance that can prevent “no drain” type complaints.

• Unplug the washer for 1 minute, then retry a cycle
• Clean the drain pump filter (remove lint and foreign objects, then reinstall and secure it)
• Confirm the drain hose is not kinked or shoved too far into the standpipe
• Verify both water supply valves are fully open
• Run a rinse and spin to see if the issue is cycle-specific

Why it matters

A targeted repair can extend the life of your Kenmore Elite washer for years; replacing a single failed component (like a drain pump, inlet valve, or door lock) is often far more cost-effective than replacing the entire appliance.

Last updated: February 2026

A Kenmore washer typically lasts 10 to 15 years with normal household use. For your Kenmore Elite washer 79641582410, routine care like cleaning the pump filter, using the right detergent amount, and avoiding chronic overloading helps you reach the longer end of that range (see the 79641582410 owner's manual).

Typical lifespan and what affects it

Most washers land in the same general window, but these factors move the needle:

• Load habits: frequent overloading increases wear on the tub, shocks, and bearings
• Drain care: a clogged pump filter makes the drain pump work harder and can shorten pump life
• Water quality: sediment can stress inlet valves and slow filling
• Detergent use: too much detergent can cause excess suds and extra rinse and drain work
• Door seal care (front load): keeping the boot clean and dry reduces odor and leaks

Common wear items over time (and what they do)

These parts often show symptoms before the washer reaches end-of-life:

Symptom you notice	Common cause	Example part for model 79641582410
Won’t drain, drains slowly, or hums	Drain pump or blockage	Drain pump motor (4681EA2001T) - washer part by lg electronics 4681EA2001T
Won’t fill, fills slowly, or stops mid-fill	Water inlet valve or screen restriction	Lg washer single-solenoid water inlet valve 5220FR2006H
Door won’t lock or cycle won’t start	Door lock or strike issue	Lg washer door lock EBF61315802

Maintenance that extends washer life

We recommend these practical habits for Kenmore front-load designs:

• Clean the drain pump filter regularly and remove lint and foreign objects
• Keep the washer level to reduce vibration and suspension wear
• Use HE detergent and measure carefully
• Leave the door ajar between loads so the boot can dry
• Check fill hoses for kinks and clean inlet screens if filling slows

Why it matters

Washer lifespan is usually limited by a few high-stress systems (drain, fill, and door locking). Preventive maintenance reduces strain on those systems, helps cycles finish normally, and lowers the chance of leaks or no-drain failures.

Last updated: February 2026

Your Kenmore Elite washer’s model number is printed on the appliance identification plate. On model 79641582410, the Use & Care Guide notes the ID plate is located inside the washer door, so opening the door and checking the door opening area is the fastest way to confirm your exact model.

Where to look on the washer

Check these common ID-plate locations (start with the first one):

• Inside the washer door opening (door jamb area)
• Along the inner edge of the door opening near the hinge side
• Around the front opening near the door lock area
• On the cabinet frame just behind the door seal (door boot)

For the exact location reference for this series, use the 79641582410 owner's manual.

What the model number looks like

Kenmore Elite front-load model numbers are typically a long number string. You may see formatting like:

What you see	What it means
796.4158#	Model series format shown in the manual
79641582410	Full model number used to match parts
Serial number	A separate number used for manufacturing ID

Tips to make sure you copy it correctly

Small character mistakes can pull up the wrong parts list, especially for door, pump, and valve components.

• Write down the full model number exactly as printed
• Record the serial number too (helpful for service and production changes)
• Avoid using only the “796” prefix; many Kenmore models share it
• If the label is worn, take a clear photo with the door open and good lighting

Why it matters

We use your exact model number to match the correct Kenmore Elite washer parts (for example, a door lock, drain pump motor, or water inlet valve) and to ensure diagrams and troubleshooting steps align with your washer’s configuration.

Last updated: February 2026

Kenmore Elite is a long-running Kenmore product line (not a single “made in” year). For your Kenmore Elite washer model 79641582410, the exact manufacture date is tied to the unit’s serial number and purchase date; we use the identification plate inside the washer door to determine it.

How to find the manufacture timeframe for model 79641582410

Use the information your washer already provides:

• Open the door and locate the identification plate inside the door opening
• Write down the model number (79641582410) and the serial number
• Record the date of purchase from your receipt (the manual provides a space to note it)
• Compare the serial number format to the decoding guidance in the 79641582410 owner’s manual
• If you are ordering parts, match parts by model number + serial number range when available

What “Kenmore Elite” means (and what it does not)

“Kenmore Elite” is a premium tier within the Kenmore brand; it spans multiple years and multiple washer designs.

Term	What it refers to	What it does not tell you
Kenmore	The brand name	The exact build date
Kenmore Elite	A higher-end product line	The factory date for your specific unit
79641582410	Your exact washer model	The purchase date (that comes from your receipt)

Why it matters

Knowing the correct manufacture timeframe helps us match the right replacement parts and troubleshooting steps for your exact configuration. This is especially important for components that can vary by production run, such as the door lock, drain pump, or water inlet valve.

Last updated: February 2026