Frigidaire FGGH3047VFA free standing gas range Parts

Yes. Looking up parts by model number is the most accurate way to get compatible replacement parts for your Frigidaire gas range model FGGH3047VFA, because the model number ties directly to the correct diagrams and part lists for that exact build.

Frigidaire places the serial plate where it is easy to access when you need parts or service. Use our FGGH3047VFA owner's manual and check these common locations:

• Open the lower storage or warmer drawer; check the right-hand surface of the oven front frame
• Check the lower right front frame of the range
• On some installations, the plate may be under the cooktop
• Record both the model number and serial number (and any lot number/letter)

Once you have FGGH3047VFA, match parts by function and symptom, then confirm fit by the model-based listing.

• Start with the symptom (no bake, no broil, oven not heating evenly, etc.)
• Use the model number to narrow to the exact parts list
• Compare the part name and identifiers before ordering
• If multiple similar parts appear, use the serial number range/lot info to choose correctly

Ranges often have small design changes across production runs. Using the exact model number (and serial/lot info) helps prevent ordering a look-alike part that mounts differently, uses a different connector, or is calibrated differently.

Last updated: February 2026

On the Frigidaire FGGH3047VFA gas range, replacing an oven igniter typically means accessing the bake or broil burner inside the oven, swapping the igniter, then verifying ignition. After replacement, the igniter should glow and the burner should light within about 60 seconds in normal operation.

• Turn off power to the range at the breaker; igniters run on electricity.
• Shut off the gas supply valve.
• Let the oven cool completely.
• Use gloves; sheet metal edges inside the oven can be sharp.
• Take a quick photo of wire routing and connector positions before disconnecting anything.

1. Remove oven racks and the oven bottom panel (and flame spreader if equipped).
2. Locate the igniter mounted to the burner tube near the burner ports.
3. Disconnect the igniter wiring (connector or wire nuts, depending on harness style).
4. Remove the igniter mounting screws and lift out the old igniter.
5. Install the new igniter in the same position and secure it with the mounting screws.
6. Reconnect wiring, reassemble panels and racks, restore gas and power.

We use the same ignition checks described for this style of range:

• Set the oven to Bake at 300°F and watch for the igniter to glow.
• In normal operation, the burner should ignite within 60 seconds.
• Let it cycle once, then turn the oven OFF.

A weak or failed igniter is one of the most common reasons a gas oven will not heat. The igniter must draw enough current to open the gas valve; when it cannot, you may see glowing with no flame, long preheat times, or intermittent heating.

For panel removal, wiring routing, and any model-specific fastener locations, follow the FGGH3047VFA installation guide and the FGGH3047VFA owner’s manual.

Last updated: February 2026

On the Frigidaire gas range model FGGH3047VFA, the model and serial number plate is typically on the lower right front frame of the oven, accessible when you open the storage or warmer drawer. This plate lists the model number, serial number, and key electrical ratings.

Check these common tag locations in this order:

• Open the lower storage/warmer drawer and look at the right-hand front frame
• Look along the oven front frame near the drawer opening
• If you do not see it there, check the lower panel area
• As an alternate location, check under the cooktop

For diagrams and model-specific references, use the FGGH3047VFA owner's manual.

The serial plate is more than a sticker; it helps us match the correct Frigidaire parts and specifications.

• Use a flashlight; the plate is often in a shadowed area
• Wipe grease and dust with a damp cloth (do not soak the label)
• Write the model and serial numbers down before ordering parts

Frigidaire ranges can look similar across model families, but burners, igniters, control boards, and drawer components can differ. Using the exact model number from the serial plate prevents ordering the wrong replacement part.

Last updated: February 2026