Kenmore 36314382000 dishwasher Parts

Yes. We still support replacement parts for many Kenmore dishwashers, including model 36314382000, by matching parts to your exact model number and symptom. Commonly replaced items include the water inlet valve, drain hose, door seals, racks, and wash system components.

How to find the right part for your Kenmore 36314382000

Use your model number (36314382000) and then narrow by the problem you are fixing. These are reliable starting points:

• Leaking at the door: check the door seal and door seal insert
• Not filling or filling slowly: check the inlet valve and household shutoff
• Not draining: check the drain hose and drain solenoid components
• Poor cleaning: check the spray arm and pump/motor area
• Rack problems: check the lower rack and rack rollers

Popular parts that are still available for this model

Here are examples of in-stock parts commonly used on 36314382000:

Symptom	Part to check	What it affects
Won’t fill / low water	Dishwasher water inlet valve WD15X10003	Water entering the tub
Won’t drain / standing water	Dishwasher drain hose WD24X10014	Water leaving the tub
Leaks at the door	Dishwasher door seal insert WD08X10015	Sealing between door and tub
Dishes not getting clean	Spray arm WD22X155	Water spray and coverage

Why it matters

Kenmore is a brand name used across multiple manufacturers and designs, so parts are model-specific. Using the exact 36314382000 match prevents ordering a look-alike part that does not fit, leaks, or fails early.

Helpful DIY resources

If you are troubleshooting by symptom, our guides can speed up diagnosis:

• Kenmore 363 electronic control model dishwasher error codes
• How to clean and maintain your dishwasher
• How to use your dishwasher efficiently

Last updated: February 2026

Your Kenmore dishwasher’s model number is printed on the appliance ID label, usually visible when you open the door. For Kenmore model 36314382000, the label is typically on the inner door frame or along the tub opening; match the full number exactly to order the right parts.

Where to look for the model number label

Check these common locations in this order:

• Along the top or side edge of the door opening (inner frame)
• On the tub rim near the latch area
• On the inside edge of the door itself
• On the side of the tub wall (visible with the door open)
• If the label is damaged: on the rear panel or lower side frame (may require pulling the unit out)

What the model number looks like (and what to write down)

Record the model number exactly as shown on the label.

What to capture	Example	Why it matters
Model number	36314382000	Ensures parts fit your exact Kenmore dishwasher
Serial number	(varies)	Helps identify production run details for service
Prefix/suffix characters	(if present)	Some parts change by revision

Why matching the full model number matters

Kenmore dishwashers can look identical but use different racks, seals, valves, or pump assemblies. Using the exact model number helps us match components like the dishwasher water inlet valve WD15X10003 or the mechanism WD26X10013 to your specific build.

Quick tips if the label is hard to read

• Wipe the label gently with a damp cloth; avoid abrasive pads.
• Use your phone camera with flash, then zoom in on the photo.
• Copy numbers carefully; a single digit change can point to a different parts list.

Last updated: February 2026

Yes; repairing your Kenmore dishwasher model 36314382000 is worth it when the failure is limited to one common wear item (leak, fill, drain, or wash performance) and the total repair cost stays well below the cost of a comparable replacement dishwasher.

Quick repair vs. replace rules

• Repair when the problem is isolated (one symptom, one system).
• Repair promptly for any leak to prevent cabinet and floor damage.
• Replace when multiple major symptoms happen together (leak plus no-drain plus loud motor).
• Replace when the tub is damaged or corrosion is severe.
• Compare parts cost plus labor time against a new unit with a warranty.

Repairs that are often worth doing on model 36314382000

• Won’t fill or fills slowly: replace the dishwasher water inlet valve WD15X10003.
• Won’t drain or drains poorly: inspect for kinks or splits; replace the dishwasher drain hose WD24X10014 if restricted.
• Poor cleaning: clear spray-arm jets; replace the spray arm WD22X155 if cracked or the jets are worn.
• Door leaks: replace the dishwasher door seal insert WD08X10015 if the insert is torn or flattened.

Cost and effort comparison

Symptom	Typical fix	Typical effort
Slow fill or no fill	Inlet valve	Medium
Standing water	Hose or drain components	Low to medium
Weak spray	Clean or replace spray arm	Low
Water at door	Door seal insert	Low

Why it matters

A targeted repair restores normal wash cycles and prevents water damage; a quick diagnosis also keeps you from replacing a good dishwasher for a single failed part. For electronic symptoms (flashing lights, cycle stopping), use Kenmore 363 electronic control model dishwasher error codes to narrow the problem before buying parts.

Last updated: February 2026

On Kenmore dishwasher model 36314382000, the F2E2 error code points to a keypad or user interface (UI) communication problem. In most cases, the control is not reliably “seeing” button presses, or the UI is not communicating correctly with the main control.

Quick checks we recommend first

• Reset power: turn the dishwasher off at the breaker for 5 minutes, then restore power.
• Make sure no keys are stuck: press each button once to confirm it moves freely.
• Dry the console area: wipe moisture from the control panel and inner door edge.
• Cancel the cycle and restart a normal cycle.
• If the code returns quickly, plan on inspecting wiring connections to the UI and control.

What usually causes F2E2

Likely cause	What you may notice	Typical fix
Stuck or shorted keypad	Random beeping, buttons not responding	Replace UI/keypad assembly (model-specific)
Loose or corroded UI harness connection	Code comes and goes	Reseat and secure connectors
Main control not processing UI signals	Dishwasher won’t start or won’t accept selections	Replace main control (model-specific)

Related symptoms and parts we often check

Even though F2E2 is a UI-related code, these checks help rule out “false” errors caused by moisture, vibration, or door issues:

• Confirm the door closes firmly and latches consistently.
• Check for leaks that can wet the console area; a worn seal can contribute. If you see water at the door edge, inspect the dishwasher door seal insert WD08X10015 and the door seal.
• If the unit also has draining problems, address those separately using Kenmore 363 electronic control model dishwasher error codes.

Why it matters

When the UI and main control cannot communicate correctly, the dishwasher may ignore selections, stop mid-cycle, or refuse to start. Fixing the keypad or connection issue restores reliable cycle selection and prevents repeat shutdowns.

Last updated: February 2026

On a Kenmore dishwasher model 36314382000, an E25 code points to a drain problem, most often a blocked drain pump area, a restriction in the drain path, or a drain pump cover that is loose or not seated correctly. Clearing the blockage and restoring proper draining typically resolves the code.

What to check first (fast, no tools)

• Cancel the cycle and let the unit drain, then restart a short cycle.
• Remove standing water from the tub (if present) so you can inspect the sump area.
• Check the drain hose for kinks, crushing, or a clogged high-loop/air-gap connection.
• Make sure the sink/disposer inlet where the dishwasher drains is not blocked.
• Listen during drain: a loud hum with little or no water movement usually indicates a blockage.

Parts that commonly relate to an E25-style drain issue

If the dishwasher is not draining, these model-compatible parts are common suspects:

• Dishwasher drain hose WD24X10014
• Bracket & so WD21X10268
• Dishwasher drain solenoid kit WD21X10060

Quick symptom-to-part guide

What you notice	Most likely area	What to do next
Water stays in tub after cycle	Drain path restriction	Inspect/clear hose and sink connection; check dishwasher drain hose WD24X10014
Hums but won’t drain	Pump area blocked	Clear debris at sump/pump inlet; verify drain components move freely
Drains sometimes, not always	Solenoid/actuator issue (on some designs)	Inspect linkage and solenoid operation; consider dishwasher drain solenoid kit WD21X10060

Why it matters

A drain fault can stop the cycle to prevent overflow and keep dirty water from recirculating. Fixing the restriction early also helps protect the pump and improves wash performance.

Related troubleshooting help

For Kenmore electronic-control models, use Kenmore 363 electronic control model dishwasher error codes to match the exact code behavior and recommended checks.

Last updated: February 2026