How to remove bottom grille on GE refrigerator?
On the GE CYE22TSHPSS bottom-mount refrigerator, the bottom grille (base grille) typically comes off by removing any retaining screws (if present) and then pulling the grille straight out to release the tabs/clips. Reinstall by aligning it and sliding it back into place, then reinstalling screws.
Quick steps
- Unplug the refrigerator or switch it off at the control for safety.
- Look along the top edge of the bottom grille for screws; remove them with a Phillips screwdriver.
- Grip the grille at both ends and pull straight outward (avoid twisting).
- If it feels stuck, gently work side-to-side to release the retaining tabs.
- To reinstall, line up the tabs with the slots and push or slide the grille into position.
- Reinstall screws (if used) and confirm the grille sits flush.
What to check if it will not come off
- Hidden fasteners: Some versions use screws at the ends or along the top lip.
- Tab tension: Pulling outward evenly from both sides prevents a tab from binding.
- Leveling legs: If the front leveling legs are lowered tightly to the floor, raising them slightly can give you more clearance to pull the grille straight out.
Tools and time
| Item | Typical need | Notes |
|---|---|---|
| Phillips screwdriver | Often | For retaining screws (if equipped) |
| Work gloves | Recommended | Helps grip and protects hands |
| Time | 5 to 10 minutes | No special tools usually needed |
Why it matters
We remove the bottom grille to access and clean the area at the front base of the refrigerator and to help with certain service tasks. Pulling straight out and supporting both sides helps prevent broken tabs and keeps the grille fitting tightly afterward.
For model-specific diagrams and any fastener locations called out for your unit, use the CYE22TSHPSS owner's manual.
Last updated: February 2026
What is the most common problem with GE refrigerators?
The most common GE refrigerator complaint is a cooling problem (warm fresh-food section, freezer too warm, or temperatures that swing). On the GE CYE22TSHPSS, the most frequent root causes are airflow issues, a failing evaporator fan, a defrost problem, or a bad temperature sensor; use the CYE22TSHPSS owner's manual to match symptoms to checks.
Most common symptoms customers notice
- Fresh-food section warm but freezer seems OK
- Freezer warm and ice cream soft
- Loud humming, rattling, or a fan noise that comes and goes
- Water leaking or puddles near the refrigerator
- Ice maker or water dispenser performance drops
Quick checks we recommend first (no parts yet)
- Confirm vents are not blocked by food packages (air must circulate).
- Set temperatures to normal targets: 37°F fresh food and 0°F freezer.
- Clean dust from the condenser area (restricted heat release causes poor cooling).
- Check door seals for gaps, tears, or areas not gripping the cabinet.
- If the unit recently lost power, allow 24 hours to stabilize temperatures.
Common causes and the parts that usually fix them
| Symptom | Likely cause | Part that often resolves it (if failed) |
|---|---|---|
| Warm temps, weak airflow | Evaporator fan not running | GE refrigerator evaporator fan motor WR60X26866 |
| Temps swing, food freezing then warming | Sensor reading wrong | Refrigerator temperature sensor WR55X10025 |
| Frost buildup, warm fridge, fan noise from ice | Defrost system issue | Refrigerator defrost heater WR51X10132 or refrigerator defrost bi-metal thermostat WR50X10108 |
| Water/ice tastes off, slow water flow | Clogged filter | GE refrigerator water filter RPWFE |
Why it matters
Cooling and airflow problems can spoil food quickly and make the compressor run longer than normal. Catching a weak fan, iced-up evaporator, or drifting sensor early helps restore stable temperatures and reduces wear on the sealed system.
Helpful GE troubleshooting resources
- Use GE refrigerator error codes if your display shows a code or you suspect an electronic control issue.
Last updated: February 2026
Why is there ice in the bottom of my GE refrigerator?
Ice collecting on the bottom of your GE CYE22TSHPSS bottom-mount refrigerator almost always happens when defrost water cannot drain away; it pools, then refreezes into a sheet of ice. The most common cause is a clogged or frozen defrost drain path, sometimes made worse by warm air leaks at the door.
Quick checks we recommend first
- Unplug the refrigerator or turn off power at the breaker.
- Pull out the freezer drawer and look for a solid ice layer on the freezer floor.
- Check for frost buildup on the back freezer panel (a sign of a defrost or airflow issue).
- Inspect door sealing surfaces for gaps, tears, or areas not making contact.
- If you recently had the doors removed or adjusted, recheck alignment and closing.
How to clear a clogged or frozen defrost drain
- Remove food and bins as needed to access the drain area.
- Melt the ice with a hair dryer on low or by placing towels and letting it thaw (keep heat moving).
- Flush the drain with hot water using a turkey baster or squeeze bottle until it flows freely.
- Clean debris from the drain trough and confirm water reaches the drain pan underneath.
For model-specific access steps and panel removal guidance, use the CYE22TSHPSS owner's manual.
Parts that commonly relate to this symptom
If you see heavy frost, repeated refreezing, or inconsistent temperatures, these parts are often involved:
- Defrost control components (heater and thermostat)
- Temperature sensing (controls when to defrost and how long to run cooling)
- Door gasket (warm air leaks create excess frost and meltwater)
| Symptom you notice | Most likely area | Example part for CYE22TSHPSS |
|---|---|---|
| Ice sheet on freezer floor, little frost elsewhere | Drain frozen or clogged | (No specific drain part listed; clear and flush) |
| Heavy frost on back freezer wall | Defrost system issue | Refrigerator defrost heater WR51X10132 or refrigerator defrost bi-metal thermostat WR50X10108 |
| Condensation, frost near door edges | Door not sealing | Refrigerator freezer door gasket WR14X36194 |
Why it matters
When defrost water cannot drain, it refreezes and can block airflow, reduce cooling performance, and lead to water leaks when the ice melts. Fixing the drain and any door-seal or defrost issues prevents repeat icing.
Last updated: February 2026





