Kenmore 11069622800 dryer Parts

To identify your Kenmore dryer model, look for the model and serial number label on the dryer cabinet. For Kenmore model 11069622800, the label is typically found around the door opening area or on the back of the dryer near the top; confirm the exact label location in the 11069622800 use & care manual.

Where to look on a Kenmore dryer

Check these common spots first (in this order):

• Inside the dryer door opening on the cabinet frame
• On the back panel near the top edge
• Along the door opening lip (left or right side)
• Behind the lower access panel (if your design has one)
• On the inside of the cabinet side panel (visible when the door is open)

What the model number looks like (and why it matters)

Kenmore model numbers are usually a long string of numbers (often 10 to 12 digits). For parts lookup and diagrams, you want the full model number, not just “Kenmore 110” or a partial number.

Quick ID checklist

Item on label	What to record	Why we need it
Model number	Full number (example: 11069622800)	Ensures correct parts and diagrams
Serial number	Full serial	Helps confirm production details
Type	Electric or gas (if shown)	Affects heating and ignition parts

Tips to avoid mix-ups

• Write the model number exactly as shown, including any leading zeros.
• If the label is worn, use a flashlight and take a close-up photo.
• If you are ordering parts, match your model number first, then choose the part.

Why it matters

Kenmore dryers can look similar across multiple model series, but internal components (like the door switch, belt, or thermostat) can vary by model. Using the exact model number helps prevent ordering the wrong replacement part and reduces repair downtime.

Last updated: January 2026

Yes. For Kenmore dryer model 11069622800, the most reliable “reset” is a power reset: turn the dryer off, unplug it (or switch the breaker off) for about 1 minute, then restore power and try starting a cycle again. See the 11069622800 use & care manual for normal start/stop steps.

Quick reset steps (model 11069622800)

• Turn the cycle selector to OFF.
• Unplug the dryer (or turn both dryer breakers off if it’s hardwired).
• Wait 60 seconds.
• Restore power.
• Close the door firmly, select a cycle, and press PUSH TO START.

If it still will not start after a reset

On this model, a “reset” will not fix a failed safety switch or control issue. Check these common no-start causes:

• Door not fully closed or a failed door switch
• Timer not set to a running position (dial not moved past OFF)
• Start switch not making contact
• House fuse or breaker issue (many electric dryers use two fuses/breakers)
• Motor not running due to an internal fault

If the door feels closed but the dryer acts like it is open, the dryer door switch WP3406107 is a common part to test/replace.

What “reset” means on this dryer (and what it does not)

Reset type	What it does	When it helps
Power reset (unplug 1 minute)	Clears a temporary control glitch	Random no-start, odd behavior after outage
Cycle restart (open/close door, reselect cycle)	Re-initializes the start sequence	Door not latched, cycle not selected
Replacing a failed component	Fixes the root cause	Repeated no-start, intermittent stopping

Why it matters

Resetting is a safe first step because it rules out a simple power or control hiccup before you spend time diagnosing parts like the door switch, push-to-start switch, or timer.

Last updated: January 2026

For Kenmore dryer model 11069622800, the total cost to replace the heating element is usually the price of the part plus labor. Because labor rates and the exact heater assembly used can vary by configuration, we can’t quote one fixed total for this model without matching the exact heater part.

Typical cost range (part + labor)

Here’s what most customers can expect when replacing an electric dryer heating element:

• Heating element part: often $40–$150+ (varies by design and whether it’s an element-only or heater housing assembly)
• Labor: commonly $120–$250 depending on local rates and access
• Total typical range: $160–$400+

Cost item	Typical range	What changes it most
Heating element part	$40–$150+	Element style, included housing, OEM vs. aftermarket
Labor	$120–$250	Service rates, disassembly time, stacked/closet installs
Total	$160–$400+	Part type + labor

Before you buy a heating element

On model 11069622800, “no heat” is often caused by airflow or safety devices opening, not just the heater coil. Check these first:

• House power: many electric dryers can tumble with a partial power issue but not heat
• Lint screen and venting: restricted airflow can overheat the heater circuit
• Thermal cut-off or thermal fuse: these can open if the dryer overheats
• High-limit thermostat: can fail and interrupt heat

If you suspect an overheat event, replacing the safety devices as a set is often smarter than replacing only one.

Parts that commonly relate to “no heat” on this model

If your Kenmore 11069622800 is not heating, these model-compatible parts are commonly involved:

• Dryer thermal cut-off fuse kit 279816
• Dryer high-limit thermostat WP3977767
• Dryer operating thermostat WP3387134

Why it matters

Replacing the wrong part can waste money and time. A failed heating element can be obvious (broken coil), but an airflow restriction or a blown thermal cut-off can cause repeat failures if the venting problem isn’t corrected.

For venting and safety basics specific to this dryer platform, follow the guidance in the 11069622800 installation guide.

Last updated: January 2026

Yes, repairing a Kenmore dryer model 11069622800 is often worth it when the failure is a common wear part and the total repair cost stays well below replacement cost. If you are facing multiple major failures, persistent overheating, or repeated breakdowns, replacement can be the better value.

A practical decision checklist (for model 11069622800)

Use these quick checks before you spend money:

• Confirm the symptom: no start, no heat, long dry times, or loud noise
• Rule out venting problems first (poor airflow can mimic “bad dryer” symptoms)
• Price the likely repair parts plus labor (if you are not DIY)
• Consider overall condition: drum support wear, cabinet rust, or recurring shutdowns
• Factor in safety: stop using the dryer if you smell burning or the unit overheats

For Kenmore 11069622800 operating, care, and troubleshooting steps, use the 11069622800 dryer use and care manual.

Repairs that are commonly “worth it” on this model

These are typically straightforward and relatively low-cost compared with replacing the dryer:

• Broken or slipping belt: dryer drum belt 341241
• Dryer will not start when the door is closed: dryer door switch WP3406107
• Overheating or no-heat safety shutdown (after correcting airflow restrictions): dryer thermal cut-off fuse kit 279816

Cost-to-benefit guide

What you’re seeing	What we usually recommend
One clear failed wear part (belt, door switch, thermal cut-off)	Repair is usually worth it
Multiple parts needed or repeated failures in a short time	Compare total repair cost vs replacement
Long dry times or very hot cabinet	Fix venting first, then reassess

Why it matters

On Kenmore 11069622800 dryers, restricted venting can cause long dry times and overheating that shortens the life of safety parts. Correcting airflow first helps you avoid repeat failures and makes any repair investment more likely to pay off.

Last updated: January 2026