Owner’s manual
Where is the model number on a chainsaw?
On a Craftsman gas chainsaw like model 358352180, the model number is typically printed on the saw’s identification label or ID tag on the housing. We recommend matching the number exactly as printed before ordering parts or using the 358352180 operator’s manual.
Common places to check
Look for a sticker, metal tag, or stamped plate in these spots:
- On the rear handle area (near the throttle trigger)
- On the starter (recoil) housing side
- Near the fuel tank or oil tank area
- On the bottom of the saw body (underside)
- Near the bar mount studs or clutch cover area
How to read the number correctly
Chainsaw labels can be dirty or worn; use these tips to avoid ordering the wrong Craftsman parts.
- Wipe the label with a damp rag; avoid solvents that can remove printing
- Use a flashlight at an angle to see faint ink or stamping
- Write down the full model number exactly (all digits)
- If you see multiple numbers, use the one labeled “Model” (not a patent number)
- Take a photo before the label deteriorates further
Why it matters
The model number controls parts fit and diagrams. For example, bar and chain options, fuel system routing, and ignition components can vary by model series even when the saws look similar.
Quick ID checklist
| What you’re looking at | What it’s used for |
|---|---|
| Model number (example: 358352180) | Correct parts lookup and diagrams |
| Bar length (example: 18 in.) | Matching bar and chain size |
| Engine size (cc/cu. in.) | Tuning and service reference |
Last updated: February 2026
Do you use 40 1 or 50 1 gas in a chainsaw?
For the Craftsman chainsaw model 358352180, we use a 40:1 fuel mix: unleaded gasoline mixed with 2-cycle air-cooled engine oil. Mixing at 40:1 helps protect the 2-cycle engine from damage and keeps starting and running performance consistent.
Correct mix for this Craftsman chainsaw
Use 40 parts gas to 1 part oil.
- Mix 3.2 oz of 2-cycle (air-cooled) oil with 1 gallon of unleaded gasoline
- Use 2-cycle air-cooled engine oil (not automotive oil, not marine/boat oil)
- Shake the fuel container after adding oil so the mix is uniform
- Mix only what you will use soon; old fuel causes hard starting and rough running
- If the saw will sit for 30 days or longer, drain the fuel system or use stabilizer per the 358352180 owner's manual
Quick mix chart (common sizes)
| Gasoline amount | 40:1 oil amount |
|---|---|
| 1 gallon | 3.2 oz |
| 1/2 gallon | 1.6 oz |
| 1 quart | 0.8 oz |
Why 50:1 is not the right choice here
Many newer chainsaws run 50:1, but this Craftsman 2-cycle design is specified for 40:1. Running a leaner oil mix than specified can reduce lubrication, increase heat, and shorten engine life.
If your saw is hard to start after mixing correctly
Fuel issues are the most common cause on older gas chainsaws. We recommend checking these items in order:
- Fresh 40:1 fuel mix (no stale gas)
- Primer operation and fuel delivery; replace cracked lines with ayp lawn & garden equipment fuel line, large 530069216
- Fuel cap venting; a plugged vent can starve the carburetor (see fuel tank cap 580940901)
- Carburetor condition; consider a rebuild using carburetor repair kit 530069826
- Spark plug condition and correct gap (per the manual)
Why it matters
Correct fuel ratio is the foundation for reliable starting, smooth cutting power, and long engine life on a 2-cycle Craftsman chainsaw.
Last updated: February 2026
What model number is a Craftsman 16 36cc chainsaw?
A Craftsman 16-inch, 36cc gas chainsaw does not map to one single model number because bars are often swapped. For the Craftsman model page you are viewing (358352180), the operator’s manual for this platform lists model 358.352181 with an 18-inch bar, so the correct way to identify a true 16-inch version is to read the ID tag on your saw and match it to the 358352180 owner's manual.
How to identify your exact model number (fast)
Use the saw’s ID tag first; bar length and engine size are not unique identifiers.
- Look for the model tag on the starter housing, rear handle, or near the fuel and bar-oil caps
- Write down the full number, including dots (example format: 358.XXXXXX)
- Match that number to the model listing in the manual and parts diagrams
- If the bar says 16-inch, treat it as a clue only; bars are commonly replaced
- Use the model number to order parts like fuel lines, carburetor parts, and clutch components
Why your “16-inch 36cc” description can be misleading
Many Craftsman 36cc saws share similar housings and can run different bar lengths. The manual associated with this model platform calls out 358.352181 and an 18-inch bar, so a 16-inch bar on your saw can simply mean the bar was changed.
| What you have | What it means | Best next step |
|---|---|---|
| 36cc engine | Narrows to a family of Craftsman saws | Confirm the full 358.xxxxxx model on the ID tag |
| 16-inch bar | Bar may be original or swapped | Verify bar and chain specs after you confirm the model |
| Model page 358352180 | Parts platform for this listing | Use the manual’s model reference to cross-check |
Why it matters
The exact model number controls parts fitment and safety-critical compatibility (chain brake parts, clutch, oiling system). Ordering by “16-inch 36cc” alone often leads to the wrong bar, chain, or fuel system parts.
Last updated: February 2026
