Kenmore 11082824102 electric dryer Parts

Your Kenmore dryer’s model number is printed on the model and serial number label; on model 11082824102, that label is located at the top inside the dryer door well. Once you have the full model number, you can match the correct parts, wiring, and troubleshooting steps.

Check these spots in this order:

• Top inside the dryer door well (most common for this model)
• Around the door opening on the cabinet frame
• On the rear panel (less common, but possible)
• In your paperwork; the model number is often recorded in the 11082824102 owner's manual

Kenmore model numbers are typically a long string of digits. For many Kenmore dryers, the first three digits (often 110) identify the manufacturing source, and the full number identifies the exact design.

Using the complete model number helps us ensure you get the right fit for key items like the heating circuit, drum support, and door switch.

• Write down the full model number exactly as shown
• Record the serial number too (useful for production changes)
• Take a clear photo of the label for reference
• Use the model number to confirm compatibility for common repairs like:
  • No heat (heating element, thermostats, thermal cut-off)
  • Squealing or thumping (rollers, idler pulley)
  • Won’t start (door switch, motor)

Unplug the dryer, wipe the label gently with a damp cloth, and use your phone’s flashlight at an angle to make faint printing easier to see. The 11082824102 owner's manual also explains where the label is located so you can confirm you are checking the right spot.

Last updated: February 2026

A Kenmore electric dryer like model 11082824102 typically lasts 13 years with normal household use and proper venting. Keeping airflow strong and replacing wear items early helps the dryer heat correctly, dry faster, and reduce strain on the motor and drum support system.

• Vent restriction (long runs, crushed flex duct, lint buildup)
• Overloading the drum and running back-to-back cycles
• Heat stress from poor airflow (can trip safety fuses)
• Worn drum support parts (rollers, idler, seals)
• Electrical issues (loose terminal connections, damaged wiring)

• Clean the lint screen every load; confirm the grille area is clear
• Check outside vent flap opens strongly during a cycle
• Clean the full vent path periodically; replace damaged ducting
• Listen for squealing or thumping and address it early
• If drying times increase, inspect heating and airflow components

For model-specific care and cleaning guidance, follow the 11082824102 dryer manual.

Most “dryer failures” start as airflow or wear-item problems; fixing those early prevents overheating, nuisance shutdowns, and premature motor or drum damage.

Last updated: March 2026

For Kenmore electric dryer model 11082824102, the most commonly replaced parts are the heating and safety components, plus drum drive and support wear items. These parts directly affect heat output, drying time, noise, and whether the drum tumbles smoothly.

• Dryer heating element WP3387747: no heat, weak heat, long dry times
• Dryer thermal cut-off fuse kit 279973: dryer runs but won’t heat, or heat cuts out (often tied to poor venting)
• Dryer high-limit thermostat WP3391914: overheating symptoms, heat cycling too aggressively
• Dryer idler pulley 279640: squealing, belt slip, drum not turning reliably
• Dryer blower wheel WP697772: poor airflow, rumbling, longer dry times
• Dryer door switch WP8283288: dryer won’t start or stops when door is closed

• Confirm the model number is 11082824102 on the appliance label
• Match symptoms to the heating, airflow, or drive system
• Check venting for restrictions; overheating can repeatedly blow safety fuses
• Use the wiring diagram and troubleshooting steps in the 11082824102 dryer manual

Replacing the correct “first-fail” part saves time and prevents repeat breakdowns, especially when a vent restriction is the real cause behind heating and fuse problems.

Last updated: March 2026