Kenmore Elite 11076982501 gas dryer Parts

A blown thermal fuse on your Kenmore Elite gas dryer model 11076982501 typically shows up as a dryer that will not run at all, or a dryer that runs but has heat problems after an overheating event. The sure way to confirm is a continuity test with a multimeter after safely disconnecting power.

Quick symptoms to look for

• Dryer will not start even with a cycle selected and the door closed
• Dryer starts but stops unexpectedly during a cycle
• No heat or weak heat (always rule out venting and gas supply first on a gas dryer)
• Burning smell or very hot cabinet before the failure
• Repeated overheating or long dry times leading up to the issue

How we test a thermal fuse (the definitive check)

1. Unplug the dryer (or disconnect power at the breaker) before opening any panels.
2. Access the thermal fuse location shown for your model in the owner's manual.
3. Remove at least one wire from the fuse terminal so you are not reading the rest of the circuit.
4. Set a multimeter to continuity (or lowest ohms).
5. Touch a probe to each fuse terminal.

What the meter reading means

Meter result	What it indicates	What to do next
Beep or near 0 ohms	Fuse is good (closed circuit)	Check airflow, cycling controls, and heat system
No beep or OL/infinite	Fuse is blown (open circuit)	Replace the fuse and correct the overheating cause

Fix the cause first: airflow and heat checks

Overheating is what blows a thermal fuse. Before running the dryer again, we recommend:

• Clean the lint screen and confirm it is not damaged (a torn screen can pass lint into the blower)
• Inspect and clean the entire vent run to the outside; remove kinks and crushed sections
• Confirm the outside hood flap opens freely
• For gas models, confirm the gas shutoff valve is open (the installation steps call this out) using the installation guide
• If heat is intermittent on a gas dryer, check common ignition parts such as the dryer gas valve coil kit 279834 and the igniter 279311

Why it matters

A thermal fuse is a safety device. Replacing it without correcting restricted venting or a failing heat/airflow component often leads to another blown fuse, longer dry times, and higher operating temperatures.

Last updated: February 2026

To reset your Kenmore Elite gas dryer model 11076982501, we recommend doing a simple power reset: turn the Cycle Selector to OFF, unplug the dryer (or switch the breaker off) for 1 minute, then restore power and start a new cycle per the owner's manual.

Quick reset steps (safe and effective)

• Turn the Cycle Selector Control to OFF.
• Unplug the dryer (or turn both dryer breakers off if your home uses a 2-breaker setup).
• Wait 1 minute.
• Restore power.
• Close the dryer door firmly.
• Select a cycle and temperature.
• Press PUSH TO START.

If it still will not start after the reset

These checks come straight from common “won’t run” troubleshooting for this style of Kenmore dryer:

• Confirm the dryer is plugged into a grounded 3-prong outlet.
• Check house fuses or breakers; some installations use 2 fuses/breakers.
• Make sure the door is fully closed; a failed door switch can prevent starting.
• Try a different cycle (for example, timed dry) and press PUSH TO START again.
• If the button feels normal but nothing happens, test the start switch.

Parts that commonly affect starting

Symptom	What to check	Example part for this model
Dryer does nothing when you press start	Start switch, timer, power supply	Dryer push-to-start switch WP3977456
Starts only with door held or door “click” feels weak	Door switch, latch alignment	Dryer door switch WP3406107

Why it matters

A power reset clears a “stuck” control state and forces a clean restart. If the dryer still will not run, the problem is usually power to the dryer, a door interlock issue, or a failed start circuit component.

Last updated: February 2026

Kenmore Elite gas dryer 11076982501 uses display codes to narrow troubleshooting to a specific system (power, controls, or temperature sensing). Use the code as a starting point, then follow the diagnostic and wiring checks in the owner's manual before replacing any parts.

Common display codes and what they point to

These codes are commonly used on Kenmore Elite gas dryers in this design family; use them to identify the circuit to test on model 11076982501.

• PF: Power failure or power interruption during a cycle.
• F:01: Main electronic control board fault.
• F:02: Keypad or user interface fault.
• F:20: Heater relay or heat control circuit fault.
• F:22 / F:23: Outlet (exhaust) thermistor circuit fault.
• F:24 / F:25: Inlet (intake) thermistor circuit fault.

What to do first (quick checks that solve many codes)

• Reset the control: unplug for 1 minute, then restore power.
• Confirm steady power at the outlet; avoid extension cords.
• Clean the lint screen and check the blower area for lint buildup.
• Inspect the vent run for crushing, kinks, or heavy lint restriction.
• Run Timed Dry; if it heats there but fails on sensor cycles, airflow and thermistor circuits are the priority.

Parts that often relate to thermistor and heat complaints

If your code points to temperature sensing or heat control, these model-compatible parts are common test-and-replace items:

Code or symptom	What to inspect first	Part to test/replace (if failed)
F:22 to F:25	Vent restriction, sensor wiring, connector fit	Dryer thermistor WP8577274
No heat or heat cuts out	Ignition sequence, flame sensing, burner operation	Dryer radiant sensor WP338906 or dryer gas valve coil kit 279834
PF repeats	Outlet fit, breaker, house power stability	(No part replacement is usually needed)

Why it matters

A code is a shortcut to the right checks. For example, thermistor-related codes often come back when airflow is restricted; correcting venting prevents overheating, nuisance shutdowns, and long dry times.

Last updated: February 2026