Kenmore Elite 11076982501 gas dryer Parts

A blown thermal fuse on your Kenmore Elite gas dryer model 11076982501 typically shows up as a dryer that will not run at all, or a dryer that runs but has heat problems after an overheating event. The sure way to confirm is a continuity test with a multimeter after safely disconnecting power.

• Dryer will not start even with a cycle selected and the door closed
• Dryer starts but stops unexpectedly during a cycle
• No heat or weak heat (always rule out venting and gas supply first on a gas dryer)
• Burning smell or very hot cabinet before the failure
• Repeated overheating or long dry times leading up to the issue

1. Unplug the dryer (or disconnect power at the breaker) before opening any panels.
2. Access the thermal fuse location shown for your model in the owner's manual.
3. Remove at least one wire from the fuse terminal so you are not reading the rest of the circuit.
4. Set a multimeter to continuity (or lowest ohms).
5. Touch a probe to each fuse terminal.

Overheating is what blows a thermal fuse. Before running the dryer again, we recommend:

• Clean the lint screen and confirm it is not damaged (a torn screen can pass lint into the blower)
• Inspect and clean the entire vent run to the outside; remove kinks and crushed sections
• Confirm the outside hood flap opens freely
• For gas models, confirm the gas shutoff valve is open (the installation steps call this out) using the installation guide
• If heat is intermittent on a gas dryer, check common ignition parts such as the dryer gas valve coil kit 279834 and the igniter 279311

A thermal fuse is a safety device. Replacing it without correcting restricted venting or a failing heat/airflow component often leads to another blown fuse, longer dry times, and higher operating temperatures.

Last updated: February 2026

To reset your Kenmore Elite gas dryer model 11076982501, we recommend doing a simple power reset: turn the Cycle Selector to OFF, unplug the dryer (or switch the breaker off) for 1 minute, then restore power and start a new cycle per the owner's manual.

• Turn the Cycle Selector Control to OFF.
• Unplug the dryer (or turn both dryer breakers off if your home uses a 2-breaker setup).
• Wait 1 minute.
• Restore power.
• Close the dryer door firmly.
• Select a cycle and temperature.
• Press PUSH TO START.

These checks come straight from common “won’t run” troubleshooting for this style of Kenmore dryer:

• Confirm the dryer is plugged into a grounded 3-prong outlet.
• Check house fuses or breakers; some installations use 2 fuses/breakers.
• Make sure the door is fully closed; a failed door switch can prevent starting.
• Try a different cycle (for example, timed dry) and press PUSH TO START again.
• If the button feels normal but nothing happens, test the start switch.

A power reset clears a “stuck” control state and forces a clean restart. If the dryer still will not run, the problem is usually power to the dryer, a door interlock issue, or a failed start circuit component.

Last updated: February 2026

Kenmore Elite gas dryer 11076982501 uses display codes to narrow troubleshooting to a specific system (power, controls, or temperature sensing). Use the code as a starting point, then follow the diagnostic and wiring checks in the owner's manual before replacing any parts.

These codes are commonly used on Kenmore Elite gas dryers in this design family; use them to identify the circuit to test on model 11076982501.

• PF: Power failure or power interruption during a cycle.
• F:01: Main electronic control board fault.
• F:02: Keypad or user interface fault.
• F:20: Heater relay or heat control circuit fault.
• F:22 / F:23: Outlet (exhaust) thermistor circuit fault.
• F:24 / F:25: Inlet (intake) thermistor circuit fault.

• Reset the control: unplug for 1 minute, then restore power.
• Confirm steady power at the outlet; avoid extension cords.
• Clean the lint screen and check the blower area for lint buildup.
• Inspect the vent run for crushing, kinks, or heavy lint restriction.
• Run Timed Dry; if it heats there but fails on sensor cycles, airflow and thermistor circuits are the priority.

If your code points to temperature sensing or heat control, these model-compatible parts are common test-and-replace items:

A code is a shortcut to the right checks. For example, thermistor-related codes often come back when airflow is restricted; correcting venting prevents overheating, nuisance shutdowns, and long dry times.

Last updated: February 2026