Kenmore 11026844691 washer Parts

Your Kenmore washer model number is printed on the appliance’s ID label; for Kenmore units it often starts with 110 (like 11026844691). On most washers, you’ll find that label under the lid (top-load) or around the door opening (front-load), and it’s the key to matching the correct replacement parts.

Where to look on the washer

Check these common ID-label locations first:

• Top-load washers: under the lid, along the rim of the tub opening
• Front-load washers: on the door opening frame, or just inside the door area
• Back panel: near the power cord entry or lower rear cabinet
• Control console area: behind the console or on the cabinet edge near the controls

What the model number looks like (and what to write down)

For Kenmore, the model number is usually 11 characters or longer and may include a prefix and a full model string.

What to capture	Example	Why it matters
Full model number	11026844691	Ensures parts fit your exact washer
Serial number	(varies)	Helps date the unit and confirm production run
Type	Top-load or front-load	Narrows down correct diagrams and parts

Quick tips to avoid ordering the wrong part

These steps prevent the most common mix-ups:

• Copy the model number exactly, including all digits
• Take a clear photo of the ID label before it wears or smudges
• Match parts by model first, then confirm by symptom (no spin, no drain, leaks)
• If the washer will not start or stops mid-cycle, check common failure items like the washer lid switch WP3949238

Why it matters

Kenmore model numbers identify the exact design family, wiring, and drive system. Even small model-number differences can change which drain pump, lid switch, coupling, or gear case fits.

Last updated: February 2026

A Kenmore washer typically lasts 10 to 15 years with normal household use. For Kenmore model 11026844691, consistent care (proper loading, correct detergent, and addressing small leaks or noises early) helps you reach the high end of that range.

Typical lifespan and what affects it

Most washers wear out from mechanical stress, water exposure, and vibration. These factors have the biggest impact:

• Load size and frequency (overloading shortens life)
• Installation and leveling (out-of-balance shaking accelerates wear)
• Water quality (sediment can strain fill and drain components)
• Detergent use (too much can cause residue and odor issues)
• Fixing small problems early (a minor leak can become a major failure)

Parts that commonly limit washer life

On many Kenmore top-load designs like model 11026844691, these parts often show wear first:

• Lid switch problems that stop spin or agitation
• Drain pump wear that causes slow draining or leaks
• Drive system wear that causes poor agitation or spinning
• Suspension issues that increase vibration and tub movement

If your washer will not spin or stops mid-cycle, the washer lid switch WP3949238 is a common starting point.

Quick “repair or replace” guide

Use this as a practical decision tool.

What you’re seeing	Most likely direction	Why
Minor leak, slow drain, or intermittent no-spin	Repair	Often a single part and straightforward labor
Loud grinding, heavy oil leak, or repeated drive failures	Replace or major repair	Can involve gear case or multiple drive components
Frequent out-of-balance, tub banging	Repair first	Suspension and leveling issues are often correctable

Why it matters

A washer near the end of its lifespan can still be reliable, but small symptoms (slow drain, no-spin, extra vibration) are early warnings. Catching them early helps prevent secondary damage to the motor, gear case, and tub.

Last updated: February 2026

For Kenmore washer model 11026844691, the most commonly replaced parts are the ones that wear with normal use or stop the washer for safety, filling, draining, or agitation. Start with the lid switch, drain pump, motor coupling, and agitator components.

Most common replacement parts for this model

These are frequent fixes for no spin, no drain, won’t start, weak agitation, leaks, and loud operation:

• Washer lid switch WP3949238 (won’t start, won’t spin, stops mid-cycle)
• Washer drain pump WP3363394 (won’t drain, humming, water left in tub)
• Coupling 285753A (motor runs but won’t agitate or spin)
• Agitator dog 80040 (agitator top “ratchets” or doesn’t move clothes well)
• Inlet valve 285805 (won’t fill, slow fill, overfills)
• Clutch 285785 (slow or no spin, burning smell, noisy spin)

Quick symptom-to-part guide

Symptom	Most likely part(s) to check	What you’ll notice
Won’t start or won’t spin	Lid switch	No click at lid, stops when lid is moved
Won’t drain	Drain pump, drain hose	Water stays in tub, pump hums or rattles
No agitation or no spin (motor runs)	Motor coupling	Tub/agitator doesn’t move, rubber/plastic debris
Weak agitation	Agitator dogs, agitator cam	Upper agitator slips or doesn’t “grab”
Won’t fill or fills slowly	Inlet valve	Long fill times, hot/cold imbalance

Why these parts fail most often

Wear items take the most stress in a top-load Kenmore washer like the 11026844691:

• Safety switches cycle thousands of times
• Pumps handle lint, coins, and small debris
• Couplings protect the motor by breaking first
• Agitator parts wear down from heavy loads

Tips before you order

• Match parts by model 11026844691 to ensure fit.
• If you have multiple symptoms, fix the “no start/no drain” issue first.
• Check for simple causes: kinked drain hose, clogged pump inlet, unbalanced load.

Last updated: March 2026