Kenmore 66515119K211 undercounter dishwasher Parts

For your Kenmore dishwasher, the model number is printed on the rating label located just inside the door opening, typically along the left side of the tub frame. Once you find it, match it exactly (for example, 66515119K211) when ordering parts or using the 66515119K211 owner's manual.

Where to look for the model number

Check these common label locations first:

• Open the dishwasher door and look along the left inner edge of the tub frame
• Check the top edge of the door opening (around the tub lip)
• Look along the right inner edge if you do not see it on the left
• Wipe the area with a damp cloth; soap film can hide the print
• Use a flashlight and read straight on; angled light can wash out the text

What to write down (and why)

Record the information exactly as shown on the label.

Label item	What it’s used for	Example format
Model number	Correct part fit and diagrams	66515119K211
Serial number	Production details and service reference	Letters and numbers

Why it matters

Kenmore dishwashers often share similar-looking doors and consoles, but internal parts like the dishwasher water inlet valve, drain pump, or heating element can vary by model. Using the exact model number helps us match the correct replacement part the first time.

Quick tip for parts ordering

When you search parts for this model, use the full model number (including all digits and letters). If you are installing or reinstalling the unit, follow the 66515119K211 installation guide for cabinet opening and utility-connection placement.

Last updated: February 2026

To hard reset your Kenmore dishwasher model 66515119K211, we recommend canceling the current cycle and power-cycling the unit: turn the dishwasher off at the breaker for about 1 minute, then restore power and start a new cycle using the steps in the 66515119K211 owner's manual.

Quick reset options (try in this order)

• Press Cancel/Drain (or Cancel) once, then wait for the drain to finish.
• If the controls are unresponsive, switch OFF the dishwasher circuit breaker for 60 seconds.
• Switch the breaker ON, close the door fully, then select a normal cycle and press Start/Resume.
• If the door falls open or slams shut during testing, adjust door tension before running a cycle (this is covered in the installation guide).

What a “hard reset” actually fixes

A hard reset clears a stuck control state and stops a cycle that will not advance. It often helps when you see symptoms like:

• Buttons not responding
• Cycle stuck (wash, drain, or dry)
• Dishwasher will not start after a power flicker
• Lights blinking after a canceled cycle

If it still will not run: fast checks that matter

1. Door latch: Make sure the door is fully closed and latched.
2. Power: Confirm the breaker is on and the dishwasher has power.
3. Drain issue: If water remains in the tub after canceling, check for a drain restriction; a failing pump can also prevent proper reset behavior.

Common symptom-to-part map

Symptom after reset	Most likely area	Example part for this model
Won’t drain / standing water	Drain system	Dishwasher drain pump WPW10348269
Runs but cleans poorly	Wash circulation / spray	Dishwasher spray arm WPW10491331
Water not filling	Fill system	Dishwasher water inlet valve W11175771

Why it matters

Resetting the control correctly prevents repeated mid-cycle stops and helps you confirm whether the problem is a temporary control lockup or a real failure (like a drain pump, inlet valve, or door-latch issue).

Last updated: February 2026

Common Kenmore dishwasher problems (including model 66515119K211) are no power or no start, not filling, not draining, poor cleaning, and water leaks. Many issues trace back to power, the door not latching, water supply being off, or a failed pump, valve, or heating circuit; see the 66515119K211 installation guide for basic “does not operate” checks.

Quick checks we recommend first

• Confirm the breaker is on and the dishwasher has power.
• Close the door firmly until it latches; a loose latch prevents starting.
• Make sure the cycle is selected correctly, then press Start.
• Verify the water supply valve under the sink is fully open.
• Start a short cycle; after about 2 minutes, open the door and confirm there is water in the tub.

Most common symptoms and likely causes

Symptom	What usually causes it	Parts often involved on 66515119K211
Won’t start	No power, door not latched, control issue	Electronic control board, door latch/switch (varies by version)
Won’t fill	Water supply off, inlet valve failure	Dishwasher water inlet valve W11175771
Won’t drain	Clog, drain loop issue, drain pump failure	Dishwasher drain pump WPW10348269, drain hose
Poor cleaning	Clogged filter, spray arm blockage, low water temp	Dishwasher filter W10872845, dishwasher spray arm WPW10491331
Dishes not drying	Heater circuit issue, cycle settings	Dishwasher heating element W10518394

Why it matters

A dishwasher that does not fill, heat, or drain can leave detergent undissolved, redeposit food soil, and keep the unit from completing a cycle. Catching the root cause early also helps prevent leaks and repeat clogs.

When a part replacement makes sense

• Drain problems that persist after clearing the hose and sink/disposer connection often point to the drain pump.
• No fill with confirmed water supply commonly points to the inlet valve.
• Cloudy dishes or debris after cleaning the filter and spray arm can indicate restricted wash flow.
• No heat or poor drying after selecting a heated option often points to the heating element.

Last updated: February 2026

On the Kenmore 66515119K211 Quiet Guard undercounter dishwasher, the filter is located at the bottom of the tub under the lower spray arm, typically in or around the sump area. You access it by removing the lower rack and lifting off the spray arm to reach the filter cup or screen.

How to access the filter

1. Turn off power at the breaker (recommended anytime you put hands near moving parts).
2. Pull out the lower dishrack.
3. Remove the lower spray arm (most designs lift off or unlock with a short twist).
4. Lift out the filter cup or screen assembly from the sump area.
5. Rinse the filter under warm water; use a soft brush to clear debris.

For diagrams and the exact removal method used on your 66515119K211, follow the steps and illustrations in the 66515119K211 owner's manual.

What you should look for (common filter styles)

Most Kenmore dishwashers in this series use one of these setups:

• Twist-lock filter cup: turns a fraction of a turn, then lifts out
• Flat screen: sits over the sump inlet and lifts out after the spray arm is removed
• Two-piece filter: a coarse screen plus a finer mesh cup

Filter style	Where it sits	What it prevents
Filter cup/mesh	In the sump at tub bottom	Seeds, glass, labels
Coarse screen	Over sump opening	Larger food scraps
Fine screen	Under coarse screen	Grit that can redeposit

Why it matters

A clogged filter restricts water flow and can cause poor cleaning, gritty residue, odors, and slow draining. If cleaning the filter does not improve wash performance, we typically check the dishwasher spray arm WPW10491331 for clogged jets and confirm the drain path is clear.

Quick tips to prevent repeat clogs

• Scrape off bones, toothpicks, and stickers before loading
• Run hot water at the sink for 30 to 60 seconds before starting a cycle
• Clean the filter monthly if you wash heavily soiled loads
• Keep the lower spray arm holes clear
• Avoid overloading the lower rack so water can circulate

Last updated: February 2026

Yes, repairing a Kenmore dishwasher like model 66515119K211 is usually worth it when the problem is isolated (draining, heating, filling, leaking) and the machine is otherwise in good condition; a targeted part replacement often costs far less than replacing and reinstalling a dishwasher.

Quick way we decide: repair vs. replace

• Repair when the issue is a single failed part (pump, valve, seal, spray arm) and the tub and racks are solid.
• Repair when the dishwasher still cleans well and you just need to restore normal operation.
• Replace when you have repeated breakdowns across multiple systems (wash, drain, heat, controls).
• Replace when the tub is damaged or you have chronic leaks that keep returning after seal and hose fixes.
• Replace when repair cost approaches a large share of a new unit (common rule: around 50% or more).

Common repairs that are often worth it on 66515119K211

Many “not cleaning” or “not draining” complaints come down to a few serviceable parts:

Symptom	What to check first	Example part for this model
Water left in tub	Drain path, drain pump, drain hose routing	Dishwasher drain pump WPW10348269
Dishes not dry	Heating circuit, cycle selection	Dishwasher heating element W10518394
Not filling or fills slowly	Water supply, inlet valve, shutoff turned on	Dishwasher water inlet valve W11175771
Poor wash coverage	Spray arm clogs, filter condition	Dishwasher spray arm WPW10491331
Leaks at door	Door seal and strike alignment	Dishwasher door seal and strike kit W10542314

Why it matters (cost, time, and disruption)

A repair keeps your existing cabinet fit and plumbing setup, and it avoids the extra work of uninstalling and securing a replacement unit. If you do replace the dishwasher, correct installation details still matter for safety and performance (grounded electrical supply, proper clearances, and secure mounting).

If you’re troubleshooting before deciding

We recommend following the operation checks in the 66515119K211 installation guide and then confirming basics:

• Circuit breaker or house fuse is OK
• Door closes tightly and latches
• Cycle is set correctly to start
• Water supply is turned on
• Run the shortest cycle and confirm water enters the tub within the first couple minutes

Last updated: February 2026

On a Kenmore dishwasher, an E25 code means the dishwasher is not draining correctly, most often because the drain pump area is blocked or a pump cover/filter area is not seated correctly. On model 66515119K211, start by checking for a clog and confirming the drain path is clear per the 66515119K211 installation guide.

What to check first (fast drain checks)

• Turn off power at the breaker before inspecting the sump or pump area.
• Remove the lower rack and look for debris near the sump area (labels, glass, food).
• Check the sink drain or garbage disposal inlet where the dishwasher drain connects.
• Confirm the drain hose is not kinked, crushed, or routed incorrectly.
• If the dishwasher was recently installed, confirm the drain hose routing and connection steps in the 66515119K211 installation guide.

Parts commonly involved with an E25 drain problem

If the drain path is clear but the unit still will not drain, these model-matched parts are common suspects:

• Dishwasher drain pump WPW10348269 (pump not running, jammed impeller, weak pumping)
• Dishwasher drain hose 8269144A (kinked, restricted, leaking, or internally clogged)
• Dishwasher filter WPW10463906 (restricted flow from heavy soil buildup)

Quick symptom-to-likely-cause guide

What you notice	Most likely cause	What we recommend
Standing water after cycle	Clog in sump, hose, or disposal inlet	Clear blockage; verify hose routing/high loop/air gap setup per install steps
Humming but no drain	Pump impeller jam or failing pump	Inspect for debris; replace drain pump if jam returns
Drains slowly	Partial restriction in hose or filter	Clean filter; inspect hose for soft spots or buildup
Intermittent E25	Loose debris moving around	Recheck sump area and filter seating; remove foreign objects

Why it matters

A drain fault can leave dirty water in the tub, trigger repeated error codes, and strain the drain pump. Clearing restrictions early helps protect the pump and improves wash results.

Last updated: February 2026

Water standing in the bottom of your Kenmore 66515119K211 dishwasher almost always points to a drain restriction (filter, hose, air gap, or disposer inlet) or a drain pump problem. We start by clearing the filter area and verifying the drain hose routing, then test the pump.

Quick checks that fix most standing-water problems

• Cancel the cycle and run a drain; listen for the drain pump running.
• Remove and clean the filter area and sump screen; clear labels, glass, and food debris.
• Check the sink drain/garbage disposer for a slow clog (a slow sink often means a slow dishwasher drain).
• Inspect the drain hose for kinks, crushing, or a low loop that sags.
• If you have an air gap, remove the cap and clean it out.

Drain hose routing and installation items to verify

The installation instructions for this model call out proper utility placement and using a new drain hose during installation. Use the installation guide to confirm your hose routing and connections under the sink.

What you see	Most likely cause	What we do next
Water drains slowly, some remains	Partial clog in filter, hose, air gap, disposer inlet	Clean filter area; clear hose/air gap; check disposer inlet plug
Loud hum but little or no draining	Drain pump jammed or failing	Check for obstruction; replace pump if needed
Drains sometimes, sometimes not	Intermittent blockage or weak pump	Inspect hose routing; test pump; check wiring connections
Water backs up after sink use	Sink/disposer drain restriction	Clear sink/disposer drain path

When a part is likely needed

If the hose and filter area are clear and the dishwasher still will not evacuate water, the drain pump is the next common failure point. For the 66515119K211, the correct replacement is the dishwasher drain pump WPW10348269.

If you find the drain hose is split, brittle, or permanently kinked, replace it rather than trying to patch it. This model has multiple hose options listed, including the dishwasher drain hose 8269144A.

Why it matters

Standing water can redeposit soil on dishes, create odors, and keep the unit from completing cycles correctly. Restoring full drain flow protects the circulation system, helps drying performance, and reduces repeat clogs.

Last updated: February 2026