Kenmore 11026002010 washer Parts

To hard reset a Kenmore Elite washer (including Kenmore model 11026002010), we power-cycle it to clear a temporary control glitch: unplug the washer, wait briefly, then restore power and restart a cycle. For model-specific control behavior, use the 11026002010 owner's manual.

Hard reset steps (power reset)

• Press Power/Cancel to stop the cycle.
• Unplug the washer from the wall outlet.
• Wait 1 minute.
• Plug the washer back in.
• Press Power and start a Rinse/Spin or Drain/Spin cycle to confirm it responds.

If the washer still will not start

These checks fix the most common “looks dead” or “won’t run” situations after a reset:

• Confirm the outlet has power (try a lamp or phone charger).
• Make sure the washer is plugged into a grounded 3-prong outlet (no extension cord).
• Close the lid firmly; a lid lock issue can prevent starting.
• If the lid will not lock or unlock normally, inspect the washer lid lock assembly W10404050.
• If the tub will not drain and the cycle stops, check for a drain restriction and consider the washer drain pump assembly WPW10276397.

What a hard reset does (and does not do)

What it does	What it does not do
Clears a temporary control “hang”	Fix a broken lid lock, pump, belt, or wiring
Restarts the control logic after a power interruption	Correct an installation issue (leveling, drain setup)
Lets you quickly test if the washer will respond	Replace the need for troubleshooting error codes

Why it matters

A power reset is the fastest safe first step because many Kenmore washer symptoms are caused by a momentary control fault. If the problem returns, the next step is checking the lid lock and drain system, since those conditions commonly stop a cycle.

Last updated: February 2026

Most Kenmore washers, including model 11026002010, last 10 to 15 years with normal household use. Lifespan depends most on load size, installation (leveling and drainage), and routine care; following the maintenance steps in the 11026002010 owner's manual helps you reach the upper end of that range.

Typical lifespan by use level

Use pattern	What we typically see	What helps most
Light (1 to 3 loads/week)	12 to 15 years	Keep loads balanced; clean regularly
Average (4 to 7 loads/week)	10 to 13 years	Avoid overloading; correct detergent
Heavy (8+ loads/week)	7 to 10 years	Prevent vibration; address small issues early

What shortens washer life fastest

• Overloading or consistently washing heavy items (blankets, rugs) without balancing the load
• Running the washer out of level (increases vibration and wear)
• Poor draining (standing water, slow drain, repeated drain problems)
• Using too much detergent (buildup can cause odors and performance issues)
• Ignoring early symptoms (new noises, burning smell, repeated off-balance events)

Parts that commonly wear as a washer ages

These are normal wear items that often determine whether a repair is worth doing:

• Drive system components such as the washer drive belt WPW10006384 and pulley
• Drain components (pump, hoses, clogs)
• Lid locking and sensing components
• Suspension and balance components

Why it matters

A washer near the 10 to 15 year mark can still be a good candidate for repair if the tub and cabinet are in good shape and the problem is limited to a wear part (belt, pump, lid lock). Good installation practices from the installation guide also reduce noise, vibration, and premature wear.

Last updated: February 2026

To identify your Kenmore washer model, find the model and serial tag on the washer cabinet. On Kenmore model 11026002010, the tag is typically on the top or back of the control panel, or on the side of the main cabinet near the bottom; on front-loaders it’s often in the door opening.

Where to look first (fastest checks)

• Behind the control panel (top edge or rear of the console)
• Side of the main cabinet near the bottom front corner
• Back panel of the washer cabinet
• Under the lid area on some top-load designs
• Door jamb/behind the door on front-load designs

What to write down (and why)

The model number ensures we match the correct Kenmore parts list, diagrams, and compatible replacements.

Item on tag	Example	Why it matters
Model number	11026002010	Identifies the exact washer design and parts
Serial number	(varies)	Helps confirm production series and revisions
Type/series info	(varies)	Useful when troubleshooting or ordering assemblies

Tips to avoid ordering the wrong part

• Copy the model number exactly (all digits, no spaces).
• If the tag is worn, take a clear photo and zoom in.
• Use the model number when selecting common repair parts like a lid lock, drain pump, or drive belt.
• Keep the number with your installation paperwork for future reference.

Why it matters

Kenmore washers can look similar across multiple series; the model number is what ties your washer to the correct diagrams, installation requirements, and parts such as the washer lid lock assembly W10404050 or washer drive belt WPW10006384. For placement and setup details (clearances, leveling, drain hose routing), use the 11026002010 installation guide.

Last updated: February 2026

Yes, Kenmore top load washer model 11026002010 uses a drain pump system that can trap debris, but it typically does not have a simple, user-access “lint filter” like a dryer. We recommend checking the drain path and pump area when you have slow draining, odors, or leftover water; see the 11026002010 owner's manual.

Where “filtering” happens on this washer

On most Kenmore top load washers in this design family, debris is most often caught in the drain system rather than a removable filter cup.

Common places to check:

• The drain hose for kinks, clogs, or a crushed section
• The standpipe or laundry tub drain for slow flow or backups
• The drain pump area for coins, hair pins, socks, or lint buildup
• The tub for small items trapped under the washplate

Quick checks you can do safely

Before any inspection, unplug the washer and turn off the water supply.

• Run a Drain/Spin cycle and listen for the pump running
• If water drains slowly, inspect the hose routing and height (standpipe or tub)
• Make sure the drain hose is not pushed too far down the standpipe (helps prevent siphoning)
• If you suspect a blockage at the pump, plan for water spill control (towels, shallow pan)

Parts that relate to draining (when symptoms point there)

If the washer will not drain, drains slowly, or leaves water in the tub, these parts are commonly involved:

Symptom	Most common cause	Part to consider
Hums but won’t drain	Pump jammed or failed	Washer drain pump assembly WPW10276397
Drains sometimes, sometimes not	Intermittent obstruction or weak pump	Washer drain pump assembly WPW10276397
Leaks during drain	Hose split or loose connection	Washer drain hose W11244231

Why it matters

A restricted drain path can cause long cycle times, poor spin performance, musty odors, and standing water that can damage clothing and stress the drive system.

Last updated: February 2026

The Kenmore washer model 11026002010 is typically about 3.2 cu. ft. in capacity for this 110-series style top-load platform. For the exact rated capacity for your specific configuration, check the specifications section in the 11026002010 owner's manual.

How to confirm the exact capacity

We recommend verifying capacity using the model’s published specs (not the tub size). Here are the quickest ways:

• Look for “Capacity” or “Washer capacity (cu. ft.)” in the specifications pages of the 11026002010 owner's manual
• Check the model/serial tag and match it to the spec listing in the manual
• Compare cycle options and basket style (washplate vs. agitator) because they often align with capacity class
• If you are measuring for laundry room fit, use the installation spacing guidance in the 11026002010 installation guide

Typical capacity ranges (so you know what “3.2 cu. ft.” means)

Most Kenmore top-load washers in this family fall into a few common capacity classes:

Capacity class	Typical cu. ft.	Best for
Compact	2.0 to 2.8	Small loads, tight spaces
Standard	3.0 to 3.6	Everyday family laundry
Large	3.8 to 4.8+	Bulky items, larger households

Why it matters

Capacity affects how much you can wash per load, how well items circulate, and how likely you are to see out-of-balance issues during spin. Overloading a 3.2 cu. ft. washer can also increase wear on drive components such as the washer drive belt WPW10006384 and washer motor drive pulley W10721967.

Last updated: February 2026