Kenmore Elite 79572043112 refrigerator Parts

On the Kenmore Elite 79572043112 bottom-mount refrigerator, the most reliable “ice maker reset” is a power-cycle and a proper restart of ice production: turn ice making off, clear the bin and sensors, then turn it back on and allow up to 24 hours for normal harvest and fill to resume. Use the steps in the 79572043112 owner's manual for your exact control and ice compartment layout.

• Turn the ice maker Off, wait 30 seconds, then turn it On.
• Remove and empty the in-door ice bin; reinstall it carefully so it seats fully.
• Make sure the ice compartment door closes tightly (a door left ajar can stop ice production).
• Check that the ice shutoff arm or electronic sensor path is not blocked by ice or a piled-up bin.
• If the refrigerator was recently installed or the water line was opened, purge air by dispensing water in short cycles.

• Ice bin overfilled or jammed: shake/level the ice, then reinstall the bin.
• Sensor blocked: clear ice buildup and keep a clear path between sensors.
• Ice compartment door not sealing: close firmly; warm air leaks can disrupt ice making.
• Low water flow or air in the line: replace the filter if due and flush the dispenser.

A proper reset clears bin and sensor issues that mimic a failed ice maker. It also prevents small cubes, no-ice complaints, and ice clumping that can strain dispenser components.

Last updated: February 2026

On Kenmore Elite model 79572043112, a bad compressor usually shows up as poor or no cooling even though the unit has power; you may hear repeated clicking (start attempts) or notice the compressor runs hot and continuously without bringing temperatures down. Confirming the compressor itself requires electrical and sealed-system checks.

• Refrigerator and freezer temperatures stay warm even after 24 hours of running
• Compressor area is very hot to the touch (after it has been trying to run)
• Repeated clicking or buzzing every few minutes (start device trying to engage)
• Compressor is silent and not running even though interior lights and controls work
• Frost pattern looks abnormal (for example, little to no frost on the evaporator)
• Unit runs constantly but never reaches set temperatures

Before blaming the compressor, we check these items because they can cause the same “not cooling” complaint:

For model-specific troubleshooting steps and the built-in troubleshooting guide, use the 79572043112 owner's manual.

A compressor is strongly suspected when the fans run and controls respond, but the sealed system is not moving refrigerant effectively. A technician typically confirms this with tests such as:

• Compressor winding resistance and continuity checks
• Amperage draw during start and run
• Start device and overload evaluation
• Sealed-system performance checks (pressures, restrictions, leaks)

If you need the correct replacement compressor for this model, match by model number and use the exact part listing for refrigerator compressor TCA38091801.

Replacing a compressor is a major repair; accurate diagnosis prevents replacing an expensive part when the real issue is airflow, defrost, or a start component.

Last updated: February 2026

Common problems on the Kenmore Elite refrigerator model 79572043112 include warm temperatures from airflow restrictions (dirty condenser coil or blocked vents), defrost system icing, water and ice dispenser issues, door sealing problems, and interior light or control concerns. Our 79572043112 owner's manual troubleshooting section helps match symptoms to the most likely cause.

• Not cooling or weak cooling: condenser coil clogged with dust, evaporator fan issue, or sealed system/compressor problem
• Frost buildup on the back wall or freezer: defrost sensor/heater/control issue causing the evaporator to ice over
• Ice maker not making ice: freezer temperature too warm, fill tube icing, or ice maker component failure
• Water dispenser slow or no water: clogged water filter, kinked tubing, or inlet valve supply problem
• Water leaking or puddles: blocked defrost drain, loose water line connection, or door left ajar
• Doors not sealing or sweating: worn gasket, misalignment, or debris on the sealing surface

1. Confirm temperatures: set refrigerator to about 37°F and freezer to about 0°F.
2. Check airflow: make sure vents are not blocked by food packages.
3. Clean the condenser area: dust buildup reduces cooling efficiency.
4. Inspect door sealing: look for gaps, tears, or areas that do not grip paper.
5. Reset after a power interruption: allow 24 hours for temperatures to stabilize.

If your display shows an error code, use our Kenmore 795 model bottom freezer refrigerator error codes guide to narrow the failure to a specific system (cooling, fan, defrost, or sensors). Your manual also describes Kenmore Connect phone-based diagnostics for faster troubleshooting when the refrigerator still has power.

Cooling and defrost problems can quickly lead to food spoilage, ice buildup, and compressor strain. Catching airflow, filter, and sealing issues early often prevents bigger repairs.

Last updated: February 2026

A Kenmore Elite refrigerator like model 79572043112 typically lasts 10 to 15 years with normal household use. Consistent maintenance (clean airflow, good door sealing, and timely filter changes) is what most often separates a 10-year fridge from a 15-year fridge.

• Condenser airflow and cleanliness (dust buildup makes the compressor work harder)
• Door seal condition (warm air leaks increase run time and frost)
• Stable temperatures (fresh food about 37°F; freezer about 0°F)
• Water quality and filter changes (protects the dispenser and ice maker)
• How often doors are opened and how full the compartments are

• Vacuum dust from the grille area and around the condenser region regularly.
• Keep doors closing easily; avoid overloading door bins.
• Replace the water filter on schedule; for this model, a common replacement is the genuine Kenmore refrigerator water filter 9690 AGF80300801.
• Replace the air filter when odors linger; this model uses an lg refrigerator air filter ADQ73214408.
• Follow the care and troubleshooting steps in the 79572043112 owner's manual.

A refrigerator that runs longer to hold temperature uses more energy and puts extra wear on high-cost parts like the compressor. Basic upkeep reduces run time, helps food stay safer, and delays major repairs.

Last updated: February 2026

On a Kenmore Elite refrigerator like model 79572043112, the model number is printed on the appliance’s rating label. You’ll typically find that label inside the fresh food (refrigerator) compartment on a side wall, near the top, or around the door opening; confirm the exact label location in the 79572043112 owner's manual.

• Inside the refrigerator section on the left or right interior wall
• On the ceiling area inside the refrigerator compartment
• On the frame around the door opening (near the gasket area)
• Behind the crisper drawers (look on the side walls once drawers are removed)
• On the back exterior panel (less common, but worth a quick check)

Most Kenmore Elite rating labels include several identifiers. Use the model number for parts lookup and service.

• Write the model number exactly as shown (include all digits)
• If you see a series format like 795.7205*, use the full model from the label when possible
• Match parts by model number first, then confirm part name and location in the diagram
• Use the manual’s “Parts and features” section to identify components before ordering

Kenmore model numbers (especially the 795 series bottom freezer designs) can look similar across different revisions and colors. Using the exact model number from the rating label ensures you get the correct items like a water filter, air filter, door bin, or ice maker assembly.

Last updated: February 2026

Water leaking from the bottom of your Kenmore Elite refrigerator model 79572043112 is usually caused by a clogged defrost drain (water backs up and spills), a leak in the dispenser water line, or a door seal problem that creates excess frost and meltwater. Use the steps below and your 79572043112 owner's manual to pinpoint the source.

• Look for ice or water under the crisper drawers; this often points to a defrost drain issue.
• Check the water filter area for drips after dispensing; reseat the filter and inspect the housing.
• Inspect the water line behind the unit and the tubing inside the fresh food section for wet spots.
• Check door gaskets for gaps, tears, or areas that do not seal flat.
• Confirm the refrigerator is level; a forward tilt can encourage water to run out the front.

A leak is not just a mess; it can lead to ice buildup, warm temperatures, and floor damage. Fixing the drain or water line early helps protect the evaporator area and keeps the freezer defrost system working normally.

Your manual covers the layout of key components (like the water filter and air filter locations) and includes a troubleshooting section; use the 79572043112 owner's manual to match what you see to the correct compartment and access panels.

We recommend professional service if:

• You see water coming from the sealed system area (compressor compartment)
• The leak continues after clearing the drain and checking tubing
• Cooling performance is also poor (warm fridge or freezer)

Last updated: February 2026

If your Kenmore Elite 79572043112 bottom-mount refrigerator is not cooling, the most common causes are the controls being set to OFF, Demo Mode being enabled (lights work but cooling is disabled), or the unit being in a normal defrost cycle. Use the 79572043112 owner's manual troubleshooting steps to confirm settings first.

• Make sure the temperature controls are turned ON (not set to OFF).
• Check for Demo Mode; it can look “normal” but disables cooling.
• Wait 30 minutes if you suspect a defrost cycle; temps can rise briefly during defrost.
• If the refrigerator was just installed or moved, allow up to 24 hours to reach set temperatures.
• Confirm doors are closing fully and not being held open by bins or food packages.

1. Verify control settings: Set the refrigerator and freezer to normal mid-range settings.
2. Disable Demo Mode: Follow the control-panel steps in the manual.
3. Give it time: After changes, wait several hours and recheck temperatures.
4. Listen for airflow: You should hear fans running at times; no airflow often points to a fan or frost issue.
5. Check for heavy frost on the rear freezer panel; heavy frost often indicates a defrost problem.

If the checks above do not restore cooling, these model-matched parts are commonly involved in cooling and airflow problems:

• Refrigerator defrost sensor assembly 6615JB2005R (helps control defrost operation)
• Refrigerator evaporator ADL73341411 (key cooling component inside the sealed system)
• Refrigerator condenser coil ACG73645004 (releases heat; restricted airflow here hurts cooling)
• Refrigerator compressor TCA38091801 (sealed-system component; typically requires professional service)

Running a refrigerator that is not cooling can lead to food spoilage and can also strain sealed-system components like the compressor. Confirming OFF/Demo Mode/defrost timing first prevents unnecessary part replacement.

Last updated: February 2026