Kenmore Elite 79572043112 refrigerator Parts

On the Kenmore Elite 79572043112 bottom-mount refrigerator, the most reliable “ice maker reset” is a power-cycle and a proper restart of ice production: turn ice making off, clear the bin and sensors, then turn it back on and allow up to 24 hours for normal harvest and fill to resume. Use the steps in the 79572043112 owner's manual for your exact control and ice compartment layout.

Reset steps we recommend

• Turn the ice maker Off, wait 30 seconds, then turn it On.
• Remove and empty the in-door ice bin; reinstall it carefully so it seats fully.
• Make sure the ice compartment door closes tightly (a door left ajar can stop ice production).
• Check that the ice shutoff arm or electronic sensor path is not blocked by ice or a piled-up bin.
• If the refrigerator was recently installed or the water line was opened, purge air by dispensing water in short cycles.

What to expect after a reset

What you do	What should happen	Typical wait time
Turn ice maker Off then On	Ice maker restarts its normal cycle	A few minutes
Empty and reinstall ice bin	Sensor can “see” the bin correctly	Immediate
Clear sensor path / shutoff arm	Prevents overfill or no-ice conditions	Immediate
Purge air from water line	Restores normal cube size and fill	Up to 5 minutes of dispensing

Common reasons it “won’t reset” (and what fixes it)

• Ice bin overfilled or jammed: shake/level the ice, then reinstall the bin.
• Sensor blocked: clear ice buildup and keep a clear path between sensors.
• Ice compartment door not sealing: close firmly; warm air leaks can disrupt ice making.
• Low water flow or air in the line: replace the filter if due and flush the dispenser.

Why it matters

A proper reset clears bin and sensor issues that mimic a failed ice maker. It also prevents small cubes, no-ice complaints, and ice clumping that can strain dispenser components.

Last updated: February 2026

On Kenmore Elite model 79572043112, a bad compressor usually shows up as poor or no cooling even though the unit has power; you may hear repeated clicking (start attempts) or notice the compressor runs hot and continuously without bringing temperatures down. Confirming the compressor itself requires electrical and sealed-system checks.

Quick symptoms to watch for

• Refrigerator and freezer temperatures stay warm even after 24 hours of running
• Compressor area is very hot to the touch (after it has been trying to run)
• Repeated clicking or buzzing every few minutes (start device trying to engage)
• Compressor is silent and not running even though interior lights and controls work
• Frost pattern looks abnormal (for example, little to no frost on the evaporator)
• Unit runs constantly but never reaches set temperatures

Rule out common look-alikes first

Before blaming the compressor, we check these items because they can cause the same “not cooling” complaint:

What you observe	More likely cause	What to check next
Warm temps, heavy dust under unit	Airflow restriction at condenser	Clean condenser area and confirm condenser fan runs
Warm fridge, freezer sort of cold	Airflow/damper issue	Verify vents are not blocked; check for ice buildup
Clicking, then stops	Start device or power issue	Verify outlet power; inspect wiring and connections
Frost/ice buildup, then warm temps	Defrost problem	Check defrost sensor and defrost system operation

For model-specific troubleshooting steps and the built-in troubleshooting guide, use the 79572043112 owner's manual.

When it is likely the compressor (and what happens next)

A compressor is strongly suspected when the fans run and controls respond, but the sealed system is not moving refrigerant effectively. A technician typically confirms this with tests such as:

• Compressor winding resistance and continuity checks
• Amperage draw during start and run
• Start device and overload evaluation
• Sealed-system performance checks (pressures, restrictions, leaks)

If you need the correct replacement compressor for this model, match by model number and use the exact part listing for refrigerator compressor TCA38091801.

Why it matters

Replacing a compressor is a major repair; accurate diagnosis prevents replacing an expensive part when the real issue is airflow, defrost, or a start component.

Last updated: February 2026

Common problems on the Kenmore Elite refrigerator model 79572043112 include warm temperatures from airflow restrictions (dirty condenser coil or blocked vents), defrost system icing, water and ice dispenser issues, door sealing problems, and interior light or control concerns. Our 79572043112 owner's manual troubleshooting section helps match symptoms to the most likely cause.

Most common symptoms and what they usually mean

• Not cooling or weak cooling: condenser coil clogged with dust, evaporator fan issue, or sealed system/compressor problem
• Frost buildup on the back wall or freezer: defrost sensor/heater/control issue causing the evaporator to ice over
• Ice maker not making ice: freezer temperature too warm, fill tube icing, or ice maker component failure
• Water dispenser slow or no water: clogged water filter, kinked tubing, or inlet valve supply problem
• Water leaking or puddles: blocked defrost drain, loose water line connection, or door left ajar
• Doors not sealing or sweating: worn gasket, misalignment, or debris on the sealing surface

Quick checks we recommend first (before replacing parts)

1. Confirm temperatures: set refrigerator to about 37°F and freezer to about 0°F.
2. Check airflow: make sure vents are not blocked by food packages.
3. Clean the condenser area: dust buildup reduces cooling efficiency.
4. Inspect door sealing: look for gaps, tears, or areas that do not grip paper.
5. Reset after a power interruption: allow 24 hours for temperatures to stabilize.

Parts that commonly solve these issues

Problem area	Common fix	Example part for 79572043112
Slow/no water, bad taste/odor	Replace water filter	Genuine Kenmore refrigerator water filter 9690 AGF80300801
Odors in fresh food section	Replace air filter	Lg refrigerator air filter ADQ73214408
Frost/icing and warm temps	Check defrost sensor and evaporator icing	Refrigerator defrost sensor assembly 6615JB2005R
Door not sealing	Replace gasket	Refrigerator door gasket, right ADX72930461

Error codes and built-in diagnostics

If your display shows an error code, use our Kenmore 795 model bottom freezer refrigerator error codes guide to narrow the failure to a specific system (cooling, fan, defrost, or sensors). Your manual also describes Kenmore Connect phone-based diagnostics for faster troubleshooting when the refrigerator still has power.

Why it matters

Cooling and defrost problems can quickly lead to food spoilage, ice buildup, and compressor strain. Catching airflow, filter, and sealing issues early often prevents bigger repairs.

Last updated: February 2026

A Kenmore Elite refrigerator like model 79572043112 typically lasts 10 to 15 years with normal household use. Consistent maintenance (clean airflow, good door sealing, and timely filter changes) is what most often separates a 10-year fridge from a 15-year fridge.

What affects lifespan the most

• Condenser airflow and cleanliness (dust buildup makes the compressor work harder)
• Door seal condition (warm air leaks increase run time and frost)
• Stable temperatures (fresh food about 37°F; freezer about 0°F)
• Water quality and filter changes (protects the dispenser and ice maker)
• How often doors are opened and how full the compartments are

Typical lifespan expectations (quick guide)

Component or factor	Typical impact on lifespan	What to do
Compressor and sealed system	Biggest driver of end-of-life	Keep condenser area clean and vents clear
Door gaskets	Poor seals shorten life	Inspect for gaps, tears, and warping
Ice maker and dispenser system	Can cause leaks or clogs	Replace filters on schedule and keep ice path clean
Fans and airflow parts	Poor airflow causes warm temps	Address unusual noise or warming quickly

Maintenance that helps you reach the high end (15 years)

• Vacuum dust from the grille area and around the condenser region regularly.
• Keep doors closing easily; avoid overloading door bins.
• Replace the water filter on schedule; for this model, a common replacement is the genuine Kenmore refrigerator water filter 9690 AGF80300801.
• Replace the air filter when odors linger; this model uses an lg refrigerator air filter ADQ73214408.
• Follow the care and troubleshooting steps in the 79572043112 owner's manual.

Why it matters

A refrigerator that runs longer to hold temperature uses more energy and puts extra wear on high-cost parts like the compressor. Basic upkeep reduces run time, helps food stay safer, and delays major repairs.

Last updated: February 2026

On a Kenmore Elite refrigerator like model 79572043112, the model number is printed on the appliance’s rating label. You’ll typically find that label inside the fresh food (refrigerator) compartment on a side wall, near the top, or around the door opening; confirm the exact label location in the 79572043112 owner's manual.

Common places to check first

• Inside the refrigerator section on the left or right interior wall
• On the ceiling area inside the refrigerator compartment
• On the frame around the door opening (near the gasket area)
• Behind the crisper drawers (look on the side walls once drawers are removed)
• On the back exterior panel (less common, but worth a quick check)

What the label looks like

Most Kenmore Elite rating labels include several identifiers. Use the model number for parts lookup and service.

Label item	What it’s used for	Example format
Model number	Correct parts match and service identification	795.7205* / 79572043112
Serial number	Manufacturing date tracking and service records	Letters and numbers
Electrical rating	Outlet and circuit requirements	120V, 15A (typical)

Tips to avoid ordering the wrong parts

• Write the model number exactly as shown (include all digits)
• If you see a series format like 795.7205*, use the full model from the label when possible
• Match parts by model number first, then confirm part name and location in the diagram
• Use the manual’s “Parts and features” section to identify components before ordering

Why it matters

Kenmore model numbers (especially the 795 series bottom freezer designs) can look similar across different revisions and colors. Using the exact model number from the rating label ensures you get the correct items like a water filter, air filter, door bin, or ice maker assembly.

Last updated: February 2026

Water leaking from the bottom of your Kenmore Elite refrigerator model 79572043112 is usually caused by a clogged defrost drain (water backs up and spills), a leak in the dispenser water line, or a door seal problem that creates excess frost and meltwater. Use the steps below and your 79572043112 owner's manual to pinpoint the source.

Quick checks (start here)

• Look for ice or water under the crisper drawers; this often points to a defrost drain issue.
• Check the water filter area for drips after dispensing; reseat the filter and inspect the housing.
• Inspect the water line behind the unit and the tubing inside the fresh food section for wet spots.
• Check door gaskets for gaps, tears, or areas that do not seal flat.
• Confirm the refrigerator is level; a forward tilt can encourage water to run out the front.

Most common causes and what to do

What you see	Most likely cause	What we recommend
Water pooling inside fridge, then leaking out	Clogged/iced defrost drain	Thaw the drain area, flush with warm water, clear debris
Leak happens when using dispenser/ice maker	Cracked or loose tubing	Inspect and replace damaged line such as refrigerator water tubing MJU62070602
Water near door edges, more frost than normal	Door not sealing	Clean gasket, warm and reshape, replace if torn
Water appears after heavy humidity or frequent openings	Condensation overflow	Reduce door openings, verify temps, check gasket fit

Why it matters

A leak is not just a mess; it can lead to ice buildup, warm temperatures, and floor damage. Fixing the drain or water line early helps protect the evaporator area and keeps the freezer defrost system working normally.

Helpful model-specific references

Your manual covers the layout of key components (like the water filter and air filter locations) and includes a troubleshooting section; use the 79572043112 owner's manual to match what you see to the correct compartment and access panels.

When to stop and schedule service

We recommend professional service if:

• You see water coming from the sealed system area (compressor compartment)
• The leak continues after clearing the drain and checking tubing
• Cooling performance is also poor (warm fridge or freezer)

Last updated: February 2026

If your Kenmore Elite 79572043112 bottom-mount refrigerator is not cooling, the most common causes are the controls being set to OFF, Demo Mode being enabled (lights work but cooling is disabled), or the unit being in a normal defrost cycle. Use the 79572043112 owner's manual troubleshooting steps to confirm settings first.

Quick checks we recommend first

• Make sure the temperature controls are turned ON (not set to OFF).
• Check for Demo Mode; it can look “normal” but disables cooling.
• Wait 30 minutes if you suspect a defrost cycle; temps can rise briefly during defrost.
• If the refrigerator was just installed or moved, allow up to 24 hours to reach set temperatures.
• Confirm doors are closing fully and not being held open by bins or food packages.

What to do next (in order)

1. Verify control settings: Set the refrigerator and freezer to normal mid-range settings.
2. Disable Demo Mode: Follow the control-panel steps in the manual.
3. Give it time: After changes, wait several hours and recheck temperatures.
4. Listen for airflow: You should hear fans running at times; no airflow often points to a fan or frost issue.
5. Check for heavy frost on the rear freezer panel; heavy frost often indicates a defrost problem.

Common causes and what they usually look like

Symptom	Likely cause	What you can do now
Lights on, display normal, no cooling	Demo Mode	Disable Demo Mode per manual
Temps rise then recover	Defrost cycle	Wait 30 minutes
Warm after install/move	Normal stabilization	Allow up to 24 hours
Freezer cold, fridge warm	Airflow/damper issue	Check vents, listen for fan
Frost buildup, weak cooling	Defrost system issue	Inspect for frost pattern, plan service

Parts that are often involved (when it is not a settings issue)

If the checks above do not restore cooling, these model-matched parts are commonly involved in cooling and airflow problems:

• Refrigerator defrost sensor assembly 6615JB2005R (helps control defrost operation)
• Refrigerator evaporator ADL73341411 (key cooling component inside the sealed system)
• Refrigerator condenser coil ACG73645004 (releases heat; restricted airflow here hurts cooling)
• Refrigerator compressor TCA38091801 (sealed-system component; typically requires professional service)

Why it matters

Running a refrigerator that is not cooling can lead to food spoilage and can also strain sealed-system components like the compressor. Confirming OFF/Demo Mode/defrost timing first prevents unnecessary part replacement.

Last updated: February 2026