Kenmore 11064672400 dryer Parts

To reset a Kenmore 11064672400 dryer, we power-cycle it: turn the cycle selector to OFF, unplug the dryer (or switch the breaker off), wait 1 to 5 minutes, then restore power and start a new cycle. Confirm normal operation using the 11064672400 owner's manual.

Reset steps (safe, quick)

• Turn the Cycle Selector Control to OFF.
• Unplug the dryer (or turn both dryer breakers off if it is hardwired).
• Wait 1 to 5 minutes.
• Restore power.
• Close the door firmly.
• Select a cycle and press PUSH TO START.

If it still will not start after a reset

A reset only clears a temporary control glitch; it will not fix a power, door, or start-circuit problem.

• Verify the outlet has power and the cord is fully seated.
• Check the home electrical panel; many dryers use two fuses or breakers.
• Make sure the door fully closes and latches.
• If the button does nothing, inspect the start switch and door switch.

Common parts related to “won’t start” symptoms

Symptom	What to check first	Example part for this model
No response when pressing start	Start switch, door switch	Dryer push-to-start switch WP3977456
Starts only with door held shut	Door switch	Dryer door switch WP3406107

Why it matters

Power-cycling is the fastest way to clear a stuck control state. If the dryer still will not run, the manual’s troubleshooting checks (power supply, door closed, correct cycle selection) point you to the most likely cause before replacing parts.

Last updated: February 2026

Your Kenmore dryer’s model number is printed on the model and serial number label; on model 11064672400, that label is located at the top inside the dryer door well. Once you have the full model number, we can match the correct parts, diagrams, and specifications.

Where to look for the model number label

Check these common Kenmore dryer locations in this order:

• Top inside the dryer door well (most common for this style; see the 11064672400 owner's manual)
• Inside the door opening on the cabinet frame
• On the back panel of the dryer
• Near the lint screen housing (varies by design)

What the model number looks like (and why it matters)

Kenmore model numbers are usually a long string of digits. For many Kenmore dryers, the first three digits (often 110) identify the manufacturing source, and the full number identifies the exact configuration.

Quick guide

What you find	What it tells us	What to do next
Full model number (example: 11064672400)	Exact dryer version	Use it to select parts and troubleshooting steps
Serial number	Production run info	Keep it for service records
Only “110” or partial digits	Not enough to match parts	Recheck the label for the complete number

Tips to record it correctly

Small differences matter when ordering parts like a belt, door switch, or heating element.

• Copy the model number exactly as printed (all digits)
• Write down the serial number too
• Take a clear photo of the label for reference
• Keep the info with your purchase records (the manual recommends recording it)

Why it matters

The correct model number ensures we recommend parts that fit your exact Kenmore dryer configuration, which helps avoid returns and speeds up repairs.

Last updated: February 2026

On the Kenmore dryer model 11064672400, an E1 code points to a temperature-sensing problem, most commonly the thermistor (temperature sensor) circuit reading out of range. We use the troubleshooting steps in the 11064672400 owner's manual to confirm airflow, wiring, and sensor-related causes before replacing parts.

What to check first (fast, no parts)

• Unplug the dryer for 1 minute, then restore power and retry the cycle.
• Clean the lint screen and confirm strong airflow at the outside vent hood.
• Check the vent path for crushing, kinks, or heavy lint buildup.
• Make sure the dryer door closes firmly (a door switch issue can interrupt operation).
• If the code returns quickly, plan on electrical checks of the sensor circuit.

Likely causes and what they look like

Likely cause	Common symptoms	Typical fix
Restricted exhaust airflow	Long dry times, very hot cabinet, repeated shutdowns	Clean/repair venting, confirm airflow
Failed temperature sensor (thermistor) or wiring	E1 returns early in cycle, heat seems erratic	Inspect harness, replace sensor if failed
Overheating protection opened	No heat or stops mid-cycle after overheating	Correct airflow issue; test safety devices

Parts that are often involved

If you confirm overheating or temperature control problems, these model-compatible parts are commonly used during repair:

• Dryer thermal cut-off fuse kit 279816 (overheat protection components)
• Dryer operating thermostat WP3387134 (regulates normal operating temperature)
• Dryer high-limit thermostat WP3977767 (backup safety limit)

Why it matters

An E1 condition is often triggered by poor airflow or a failing temperature-sensing circuit. Fixing venting first prevents repeat overheating, nuisance shutdowns, and damage to heating and safety components.

Last updated: February 2026