Kenmore 11071262311 gas dryer Parts

No. The Kenmore gas dryer model 11071262311 plugs into a standard 120-volt, 60 Hz, grounded 3-prong outlet on a dedicated 15- or 20-amp circuit; it does not use the 240-volt outlet that most electric dryers require. See the electrical requirements in the installation guide.

What outlet and circuit we recommend

• Use a grounded 3-prong (120V) receptacle.
• Put the dryer on a separate 15- or 20-amp circuit (time-delay fuse or circuit breaker recommended).
• Keep the outlet within about 2 ft. of either side of the dryer (typical placement guidance).
• Do not use an extension cord.
• Do not use an adapter or remove the ground prong.

Quick comparison: gas vs. electric dryer power

Dryer type	Typical plug/outlet	Typical circuit	Notes
Gas dryer (11071262311)	120V grounded 3-prong	15 or 20 amp	Electricity runs the motor, controls, and igniter; gas provides heat
Electric dryer	240V dryer outlet	30 amp	Electricity provides heat and runs the motor/controls

Why it matters

Using the correct grounded outlet and a dedicated circuit helps prevent nuisance tripping, reduces the risk of electrical shock, and keeps the dryer controls and motor running reliably during heating and tumbling.

Last updated: February 2026

For Kenmore gas dryer model 11071262311, a typical hookup includes a grounded 3-prong (120V) outlet, a gas supply line with an easy-to-reach manual shutoff valve, a flexible gas connector to the dryer’s gas pipe, and a vent duct routed to the home’s exhaust. See the installation guide for the exact connection layout and safety steps.

What you should see behind the dryer

• A manual gas shutoff valve on the home’s gas supply line (handle parallel to the pipe when open)
• A 1/2-inch NPT gas supply line feeding the shutoff valve
• A 3/8-inch flexible gas connector running from the shutoff valve area to the dryer
• A grounded 3-prong electrical outlet (120 Volt, 60 Hz, 15 or 20 amp)
• A vent connection attached to the dryer exhaust outlet (avoid crushing or kinking)

Common connection methods (gas line)

The installation instructions describe two typical ways to connect the dryer to the gas supply.

Method	What it uses	When it’s commonly used
Option 1 (recommended)	New flexible stainless steel gas connector plus flare/NPT fittings	Most standard installations where local codes allow
Option 2 (alternate)	Approved aluminum or copper tubing with proper adapters	Some existing setups; tubing length and gas type affect what’s allowed

Key safety and setup checks

• Plug into a grounded 3-prong outlet; do not use an adapter or extension cord.
• Keep the shutoff valve within about 6 feet of the dryer and easy to access.
• After connecting gas fittings, open the shutoff valve and test joints with an approved noncorrosive leak-detection solution (bubbles indicate a leak).
• Move the dryer into place carefully; avoid crushing or kinking the vent.

Why it matters

A correct hookup helps your 11071262311 dryer heat safely and vent properly. Poor venting can cause long dry times and overheating, and incorrect gas connections can create leaks that must be corrected before operating the dryer.

Last updated: February 2026

To reset your Kenmore gas dryer model 11071262311, we recommend a hard reset: turn the dryer off, unplug it (or switch the breaker off) for about 1 to 5 minutes, then restore power and try a cycle again. This clears many temporary control and sensor glitches.

Quick reset steps (safe and effective)

• Turn the cycle selector to Off.
• Unplug the dryer (or turn the circuit breaker Off).
• Wait 1 to 5 minutes.
• Restore power.
• Close the door fully and press Start.
• If the dryer still will not start, follow the checks in the 11071262311 installation guide.

If it still will not start after a reset

The installation checklist for this model points to a few basics that commonly stop a dryer from running:

• Confirm the dryer is plugged into a grounded 3-prong outlet.
• Check the house fuse/breaker (not tripped, fuse intact and tight).
• Make sure the door is fully closed.
• Verify the exhaust vent is not crushed or kinked.
• If the dryer runs but you do not feel heat after a few minutes, confirm the gas shut-off valve is open.

Part to check if the dryer thinks the door is open

If the dryer has power but will not run when you press Start, a failed door switch is a common cause on many Kenmore dryers.

Symptom	What it often points to	Example part for this model
Drum light works but dryer will not start	Door switch not closing electrically	Dryer door switch WP3406107
No response at all	Power supply issue, breaker, cord/outlet	Use the checklist in the 11071262311 installation guide

Why it matters

Resetting clears minor electronic lockups, but it will not bypass a real safety condition. On gas dryers, airflow restrictions, an open door switch circuit, or a closed gas valve can prevent normal operation and should be corrected before repeated restarts.

Last updated: February 2026