Kenmore 11066112501 dryer Parts

The Kenmore dryer model 11066112501 is a 29-inch wide electric dryer. For planning space, the installation instructions show an overall height of about 43 3/8 inches and a cabinet depth around 26 inches, with additional room typically needed behind the dryer for the exhaust vent. See the installation guide for the full dimension diagram and clearance notes.

Dimensions and clearances to plan for

Use these as your starting point when measuring your laundry area:

• Width: 29 inches (73.7 cm)
• Height: about 43 3/8 inches (110 cm)
• Cabinet depth: about 26 inches (66 cm)
• Recommended side clearance: about 1 inch on each side (helps reduce noise transfer)
• Typical rear clearance: at least 5 1/2 inches behind the dryer for the vent elbow

Quick sizing table

Measurement	What to measure	What to allow for model 11066112501
Width	Side-to-side footprint	29 inches plus side clearance
Height	Floor to top	About 43 3/8 inches
Depth	Front to back	About 26 inches plus vent space
Rear clearance	Space behind dryer	Minimum about 5 1/2 inches (vent elbow)

Why the “installed depth” is often bigger than the dryer

Even though the cabinet depth is about 26 inches, most installations need extra space because:

• The exhaust duct and elbow sit behind the dryer
• The vent needs a smooth path to reduce drying time
• Tight venting can increase heat and cause overheating issues
• Extra space makes servicing easier (belt, motor, heater box)

Measuring tips (so you do it once)

• Measure the space opening, not just the wall-to-wall distance at floor level.
• Check for baseboards, trim, and door swing that can steal an inch or two.
• If installing in a closet, plan for required ventilation openings in the door.
• Confirm your vent route and count elbows; longer or more complex venting needs more planning.

Last updated: February 2026

Your Kenmore dryer’s model number is printed on the model and serial number label on the appliance. For Kenmore model 11066112501, you’ll use that exact model number to match the correct parts list, diagrams, and repair instructions in the owner's manual.

Where to look for the model number label

Check these common locations on Kenmore dryers:

• Along the door opening on the cabinet (door frame area)
• On the inside edge of the dryer door
• On the back panel of the dryer cabinet
• On a side panel near the rear (less common)

If you find multiple numbers, use the one labeled Model (not the serial number).

What the model number tells you (and why it matters)

Kenmore model numbers often start with a 3-digit prefix that points to the manufacturer family. For example, many Kenmore dryers that start with 110 are Whirlpool-built. The full model number (like 11066112501) is what ensures the right fit for parts such as a belt, heating element, timer, or door latch.

Quick ID checklist

• Model number: used to find the correct parts and diagrams
• Serial number: used to identify production details and can help when comparing revisions
• Type: electric vs. gas affects key parts (heating system, wiring, venting requirements)

If you’re ordering parts, match by model first

Once you confirm the model number, match parts by that model to avoid wrong-fit issues.

Common symptom	Often-related part (examples for this model)
Drum not turning	Dryer drum belt 341241, dryer repair kit 4392065
No heat or weak heat	Dryer element 279838, dryer thermal cut-off fuse kit 279816
Won’t start	Dryer push-to-start switch WP3977456

Why it matters

Using the exact model number prevents ordering the wrong Kenmore-compatible part. Small design changes across similar-looking dryers can affect belt length, heater style, wiring harness connections, and even door switch mounting.

Last updated: February 2026

Common problems with the Kenmore 11066112501 dryer include not starting, no heat, long dry times, unusual noises, and the drum not turning. Most of these issues trace back to power supply problems, restricted airflow (lint or venting), or worn moving parts like the belt and drum support components; see the owner's manual.

Most common symptoms and what usually causes them

• Dryer will not run: tripped breaker or blown fuse (many electric dryers use two), door not fully closed, Start not pressed firmly, or cycle not set correctly
• Drum turns but no heat: one side of the 240V supply is out (one fuse or breaker tripped), or a failed heating or safety component
• Clothes take too long to dry: clogged lint screen, crushed or long vent run, too many elbows, or improper vent material
• Loud thumping/squealing/grinding: small items caught at drum edges, worn rollers/idler parts (often addressed with a kit)
• Stops mid-cycle or feels too hot: overheating from poor airflow; safety devices can open to protect the dryer

Quick checks we recommend first (fast, no parts)

• Clean the lint screen before every load; confirm strong airflow at the outside vent hood
• Check both household fuses or breakers for an electric dryer (the drum can run with no heat)
• Confirm the door closes and latches consistently; replace the strike if it is loose or worn
• Verify you are not using an air-only cycle when you expect heat
• Make sure the vent is 4-inch diameter and made of heavy metal (not plastic or foil)

Parts that commonly fix these problems on model 11066112501

Symptom	Common fix	Example part for this model
Drum not turning	Broken belt	Dryer drum belt 341241
No heat or overheating	Failed safety cutoff	Dryer thermal cut-off fuse kit 279816
No heat	Failed heater	Dryer element 279838
Squealing or rumbling	Worn drum support parts	Dryer repair kit 4392065

Why it matters

Airflow and heat problems do more than slow drying; they can overheat the dryer and trigger safety shutoffs. Keeping the lint path and venting clear protects the heating system, improves performance, and helps prevent repeat failures.

Last updated: February 2026