Owner’s manual
Error Codes
How much does it cost to replace a heating element in a Kenmore dryer?
For Kenmore Elite dryer model 11086762700, the heating element part typically runs about $50 to $120, and the total installed cost is commonly $150 to $350 when you include labor and a service call. Your exact total depends on whether you replace only the element or also repair heat-damaged wiring.
- Heating element (part only): $50 to $120
- Labor (if hiring a technician): $100 to $250
- Service call/diagnostic (sometimes separate): $0 to $100
- Optional wiring repair: $10 to $40
| Scenario | What’s included | Typical total |
|---|---|---|
| DIY element replacement | Part only | $50 to $120 |
| DIY plus wiring kit | Element + wiring kit | $60 to $160 |
| Professional repair | Parts + labor + service call | $150 to $350 |
If your 11086762700 is not heating, we usually check the heater circuit parts together because a failed thermostat or damaged connector can take out a new element.
- Dryer heating element WP8544771
- Dryer heating element wire kit 279457
- Dryer high-limit thermostat WP8557403
These quick checks help avoid replacing the wrong part and help explain why costs vary.
- Confirm the dryer has the correct power supply; many electric dryers can run but not heat if one leg of power is missing.
- Check for a crushed or blocked vent; restricted airflow can overheat the heater housing.
- Look for burnt terminals at the heater connections; that often means you also need a wire/terminal kit.
- If you notice a burning odor on first heat after repair, that can be normal for a new element.
For model-specific troubleshooting steps and safety notes, use the 11086762700 owner’s manual.
A heating element replacement is one of the most common electric dryer repairs, but airflow problems and heat-limit issues can cause repeat failures. Fixing the root cause (venting, thermostats, wiring) keeps drying times normal and protects the new heater.
Last updated: January 2026
How to hard reset a Kenmore dryer?
To hard reset your Kenmore Elite dryer model 11086762700, unplug the power cord (or switch the breaker off) for 1 to 5 minutes, then restore power and start a cycle. If the controls are locked, unlock them first so the buttons respond.
- Press STOP twice to end the current cycle and clear the selection.
- Unplug the dryer (or turn both dryer breakers off for electric models).
- Wait 1 to 5 minutes.
- Restore power.
- Close the door and press and hold START until the dryer starts (some loads require holding START for a few seconds).
For model-specific button behavior (STOP, START, and Control Locked), use the 11086762700 owner's manual.
A “reset” clears many temporary control issues, but it will not fix airflow, power-supply, or failed-part problems. These checks solve the most common causes:
- Control Locked is on: Press and hold CYCLE SIGNAL for 3 seconds to unlock.
- PF (power failure): Press and hold START to restart.
- AF (airflow restriction): Check for a crushed vent, lint buildup, or a blocked exterior hood.
- L2 (power supply issue): The drum may turn but the heater may not; check house fuses/breakers.
- No heat but tumbles: Verify the venting is clear and the correct heated cycle is selected.
| What you see | What it usually means | What to do next |
|---|---|---|
| PF | Cycle was interrupted by power loss | Restart with START; then hard reset if needed |
| AF | Venting is restricted | Clean venting and lint path |
| L2 | Home power issue affecting heat | Check both breakers/fuses; confirm cord/terminal connection |
If airflow is good and power is correct, heat problems often involve temperature sensing or the heater circuit. For this model, common related parts include the dryer thermistor WP8577274, the dryer high-limit thermostat WP8557403, and the dryer heating element WP8544771.
Resetting is a fast first step, but repeated PF, AF, or L2 messages usually mean the dryer is protecting itself (airflow restriction) or not getting proper power for heat. Fixing the root cause prevents long dry times, overheating, and repeat shutdowns.
Last updated: January 2026
What are the codes for Kenmore Elite dryer?
Kenmore Elite dryer model 11086762700 uses diagnostic codes to point you to a power issue, venting problem, or a control-related service fault. Common codes you may see include PF, AF, L2, and F-series service codes; use the steps below to correct the cause and clear the display.
| Code | What it indicates | What to do first |
|---|---|---|
| PF | Power failure interrupted the cycle | Press and hold START to restart the dryer |
| AF | Vent may be crushed or blocked | Inspect and clear the venting from dryer to outside |
| L2 | Home power supply issue; drum may turn but heater may not | Check both breakers/fuses; confirm cord/terminal connections |
| F-series (example: F1, F2, F20) | Service fault (control or interface related) | Power-cycle once; if it returns, schedule service |
- PF: Restore power, then press and hold START to resume.
- AF: Check the vent run for crushing, lint buildup, and a clogged exterior hood.
- L2: Verify the dryer has full 240V supply; electric dryers typically use two breakers or fuses.
- Run a Timed Dry heated cycle (not Air Only) to confirm heat operation.
- Clean the lint screen before every load to keep airflow strong.
If the dryer runs but heat is inconsistent, cycles end early, or airflow is weak, these model-compatible parts are often involved during diagnosis:
- Dryer thermistor WP8577274 (temperature sensing)
- Dryer heating element WP8544771 (electric heat source)
- Dryer blower wheel WP697772 (moves air through the drum and vent)
These codes help you avoid guesswork. AF and restricted airflow can cause long dry times and overheating; L2 can leave the drum tumbling with little or no heat; F codes typically point to an electronic issue that needs a repair decision.
For the full list of display messages and model-specific troubleshooting steps, use the 11086762700 owner’s manual and the Kenmore elite dryer error codes reference.
Last updated: January 2026
