Kenmore 10658534700 side-by-side refrigerator Parts

To replace the water filter in your Kenmore 10658534700 side-by-side refrigerator, press the eject button in the base grille below the freezer door and pull the filter straight out by the cap. Move the cap to the new filter, reinstall, then flush the dispenser.

Step-by-step: change the base-grille filter

• Locate the filter in the base grille below the freezer compartment door.
• Press the eject button and pull the filter straight out by the cap (do not twist).
• Turn the cap counterclockwise until it stops; remove and keep the cap.
• Remove the protective cover from the new filter O-rings.
• Install the cap on the new filter: align the ridge on the cap with the arrow on the filter, then turn clockwise until it snaps.
• Push the new filter in until fully seated; the eject button pops back out.

Flush and reset

After installing the new filter:

• Hold the water dispenser lever 5 seconds, release 5 seconds.
• Repeat until water flows; then continue for 2 more minutes.
• If your status light shows “Replace,” hold RESET 2 seconds until it changes to “Good.”

Check	Normal result	If not normal
Filter install	Eject button pops out	Push filter in firmly until it seats
Leaks	No drips at grille	Re-seat filter and cap, then recheck
Dispenser flow	Steady stream	Keep flushing until air clears

Why it matters

A correctly seated, flushed filter keeps water flow strong for the dispenser and ice maker and helps prevent air spurts and leaks.

For diagrams and model-specific details, use the 10658534700 owner's manual. To replace the cartridge, order the genuine Kenmore refrigerator water filter EDR3RXD1 from the parts list, or search by model number on Sears PartsDirect.

Last updated: February 2026

Most Kenmore side-by-side refrigerators are about 32 to 36 inches wide; your Kenmore 10658534700 falls in that common size range. For the exact cabinet width and required clearances for your specific unit, use the measurements and installation notes in the 10658534700 owner's manual.

Typical width ranges (what you can expect)

Side-by-side refrigerator widths are fairly standardized; the exact width depends on capacity and whether it is counter-depth.

• Standard-depth models are commonly 33 inches or 36 inches wide
• Counter-depth models are commonly 32 to 36 inches wide
• Door and handle depth can add to the overall footprint even when cabinet width is similar
• You also need extra space for door swing and airflow

Clearance matters as much as width

Even after you confirm the cabinet width, plan for the clearances the manual calls out so the refrigerator cools properly and the doors open fully.

Per the installation guidance for this style of Kenmore refrigerator, we recommend:

• 1/2 inch clearance on each side and at the top for ventilation
• 2 inches minimum next to a fixed wall (as needed for door swing)
• Extra space at the back if you have an ice maker and water line connection

What you are measuring	What to include	Why it changes
Cabinet width	Refrigerator box only	Most consistent number
Overall width	Cabinet plus doors/hinges/handles	Handles and door geometry vary
Installed space	Overall width plus side clearances	Needed for airflow and door swing

How to measure your refrigerator width (quick method)

• Measure left to right across the cabinet at the widest point (usually near the front edges)
• Measure again across the doors/handles if you need the “fits through a doorway” number
• Compare your measurement to the space in the kitchen, then add the recommended clearances

Why it matters

Width affects fit, ventilation, and door swing. Tight installs can cause warm temperatures, noisy operation, and ice maker or water dispenser issues if the water line gets kinked.

If you are also planning maintenance while you have the unit pulled out, we stock common water system parts for this model, including the refrigerator inlet valve W10408179 and the genuine Kenmore refrigerator water filter EDR3RXD1. You can also search by model number on Sears PartsDirect.

Last updated: February 2026

The most common issues we see on Kenmore refrigerators like model 10658534700 are cooling problems, water leaks, ice maker or dispenser failures, and unusual noises. These usually trace back to airflow restrictions, defrost-system trouble, water-supply issues, or worn door seals; the 10658534700 owner's manual helps confirm the correct checks and settings.

Common symptoms and what they usually mean

• Not cooling or warm temperatures: dirty condenser coils, evaporator fan problems, or a defrost failure causing ice buildup.
• Water under the refrigerator: a clogged defrost drain or a leaking water line/connection.
• No ice or slow ice production: low water pressure, a restricted filter, or an ice maker fault.
• Water dispenser slow or not dispensing: plugged filter, low supply pressure, or a valve issue.
• Buzzing, rattling, or clicking: fan blade hitting ice, loose panels, or a failing motor.

Quick checks we recommend first

1. Verify the doors close tightly and the gaskets seal all the way around.
2. Confirm the refrigerator is connected to cold water (not hot) and the shutoff valve is fully open.
3. Check household water pressure; this model’s water system is designed for 30 to 120 psi.
4. Replace the water filter on schedule; a restricted filter can affect both water and ice.
5. If cooling is weak, clean dust from the condenser area and make sure vents inside are not blocked.

Parts that commonly solve these problems (when symptoms match)

Symptom	Common part to check	Example part for this model
No water or no ice	Water inlet valve	Refrigerator inlet valve W10408179
Bad taste/slow water flow	Water filter	Genuine Kenmore refrigerator water filter EDR3RXD1
Frost buildup, warm fridge	Defrost heater or defrost bi-metal	Refrigerator heater WP2323198 and refrigerator defrost bi-metal WPW10225581
Ice maker not producing	Ice maker assembly	Refrigerator ice maker WPW10190965

Why it matters

Most “big” refrigerator failures start as small maintenance or airflow problems. Catching a restricted filter, low water pressure, or early defrost trouble quickly helps protect food temperatures, reduces ice maker issues, and prevents leaks.

For model-specific part ordering, use the parts list for 10658534700, or search by model on Sears PartsDirect.

Last updated: February 2026

On Kenmore side-by-side refrigerator model 10658534700, the model number is printed on the appliance identification label inside the refrigerator compartment. We use that model number to match the correct parts list, diagrams, and specifications in the 10658534700 owner's manual.

Where to look first (fastest checks)

• Open the fresh food (refrigerator) door and look along the inside cabinet walls
• Check near the upper side wall or ceiling area inside the compartment
• Look around the crisper drawer frame area if you do not see it up top
• If your unit has a dispenser, also check the door jamb area near the hinges

What the label typically shows

Most Kenmore refrigerator ID labels include both a model number and a serial number. Use the model number (not the serial) when ordering parts.

Item on label	What it’s used for	Example format
Model number	Parts lookup and diagrams	10658534700
Serial number	Production identifier	Letters plus numbers

Why it matters

Using the exact model number prevents ordering the wrong water filter, ice maker, door gasket, or electronic control. Even small model variations can change the correct part fit and wiring.

Ordering tip

Once you confirm the model number, you can order parts from the parts list for this model, or search by model number on Sears PartsDirect.

Last updated: February 2026