Kenmore 66513293K112 undercounter dishwasher Parts

On Kenmore model 66513293K112, you can usually force a drain by starting a cycle and then pressing Cancel/Drain (or Start/Cancel) to trigger the cancel sequence, which runs the drain pump for a short period. Confirm the exact button sequence in the 66513293K112 owner’s manual.

Quick steps to force a drain

• Press Start to begin a cycle.
• Wait 5 to 10 seconds.
• Press Cancel/Drain (or Start/Cancel) once.
• Close the door fully and wait; most units run a drain period of about 1 to 2 minutes.
• When the draining sound stops, open the door and check the tub water level.

If it still will not drain

A “won’t drain” problem is usually a blockage, a drain hose routing issue, or a failed drain component.

• Check the sink/disposer connection; the drain connection must be made before the drain trap and at least 20 in. above the floor.
• Make sure the drain hose is not kinked, crushed, or routed flat on the floor.
• If connected to a garbage disposer, make sure the disposer inlet plug was removed.
• Clean the filter area and remove debris that can jam the impeller.
• If the motor hums but no water moves, the drain pump may be worn.

Common causes and what to check

Symptom	Most likely cause	What we do next
No drain sound at all	Control not in cancel/drain, door not latched	Retry cancel/drain with door fully closed
Hums but no water moves	Pump jammed or failing	Inspect pump area; consider replacing dishwasher drain pump WPW10348269
Drains slowly	Partial clog or poor hose routing	Re-route hose per the 66513293K112 installation guide

Why it matters

Standing water can cause odors, poor wash results, and can overload the drain pump. Correct drain hose routing and a clear filter path help the dishwasher drain quickly and protect key parts like the drain pump and sump.

Last updated: February 2026

Your Kenmore dishwasher’s model number is printed on the rating label inside the door. For model 66513293K112, open the door and look along the inner edge of the tub opening (commonly on the left side); the label lists the model and serial numbers.

Where to look on the dishwasher

Check these common rating-label locations first:

• Inside the door opening on the left side of the tub frame
• Inside the door opening on the right side of the tub frame
• Along the top edge of the tub opening (near the latch area)
• On the inner door panel, near the side edge

What to write down (and why)

Record the details exactly as shown so we can match the correct Kenmore parts and diagrams.

Label item	What it’s used for
Model number (example: 66513293K112)	Ensures exact-fit parts like racks, pumps, and controls
Serial number	Helps identify production changes within the same model
Electrical ratings	Useful when troubleshooting power or control issues

Tips to avoid ordering the wrong part

Before you shop for parts like a drain pump or water inlet valve, we recommend:

• Copy the model number character-for-character (including any suffix)
• Take a clear photo of the label for reference
• Use the model number when checking diagrams in the 66513293K112 owner’s manual
• If the label is worn, look for a second label in the same door opening area

Why it matters

Kenmore dishwashers can look identical across multiple model numbers, but internal components (like the user interface, heater, or dishrack hardware) can differ. Using the exact model number keeps part selection accurate and prevents fitment issues.

Last updated: February 2026

For Kenmore model 66513293K112, a “hard reset” is usually done by canceling the current cycle and rebooting power to clear a stuck control. Start with the control-panel cancel/reset sequence, then cut power for 1 minute if the dishwasher still will not respond.

Quick reset steps (most effective order)

• Press Cancel/Drain (or Cancel) once; wait for the drain to finish (often 1 to 2 minutes).
• If the keypad is unresponsive, turn the dishwasher breaker OFF (or unplug it) for 60 seconds, then restore power.
• Close the door fully and try starting a normal cycle.
• If the dishwasher beeps but will not start, open and firmly re-close the door to confirm the latch is engaged.
• If the unit powers up but acts erratic, run a short rinse cycle to confirm normal operation.

If your model uses a heated dry reset sequence

Some Kenmore dishwashers use a keypad sequence such as Heated Dry and High Temp (pressed in a pattern) to reset the control. Use the exact sequence listed for your control panel in the 66513293K112 owner’s manual.

What a “hard reset” does (and does not do)

Action	What it clears	What it won’t fix
Cancel/Drain	Stuck cycle, paused drain	Failed pump, clogged hose
Breaker OFF 60 sec	Control glitch, frozen keypad	Door latch failure, wiring damage
Restart cycle	Confirms normal response	Underlying fill or drain problem

Why it matters

A reset is a fast way to rule out a temporary control-board lockup before replacing parts. If the dishwasher still will not fill, wash, or drain after a reset, the issue is usually mechanical (drain path) or a failed component.

When to move from reset to troubleshooting

If symptoms continue after the steps above, check common causes:

• Standing water after Cancel/Drain (possible drain restriction or pump issue)
• No water entering (possible supply issue or inlet valve)
• Humming but no drain flow (possible drain pump problem)

For drain-related problems on this model, the dishwasher drain pump WPW10348269 is a common repair part.

Last updated: February 2026

Yes, repairing a Kenmore dishwasher like model 66513293K112 is usually worth it when the problem is isolated (drain, fill, heating, racks) and the tub is in good shape; a targeted repair often restores performance for far less than replacement and avoids a full reinstall. Use the 66513293K112 installation guide to confirm basic setup checks (power, water, drain) before you decide.

When repair is the better choice

• The dishwasher fills and drains but has one clear symptom (poor draining, no heat, weak spray).
• The door closes and latches normally, and the tub is not leaking.
• You can pinpoint a common wear part (pump, inlet valve, heater, rack hardware).
• The unit is securely mounted and level (shifting can cause door and alignment issues).
• You want to avoid cabinet modifications and plumbing changes.

When replacement makes more sense

• Multiple major failures at once (control issues plus motor plus leaks).
• Persistent leaking from the tub area (not just a hose or seal).
• Repeated electrical problems (tripping breaker, intermittent power) after basic checks.
• The dishwasher is not installed to spec and would require significant rework.

Quick decision checklist (start here)

From the install guidance, we recommend verifying these basics first:

• Circuit breaker or house fuse is OK.
• Door is closed tightly and latched.
• Cycle is set correctly and Start/Resume is used correctly.
• Water supply is turned on.
• After starting, confirm there is water in the bottom of the tub within a couple minutes.

Common repairs for this model (examples)

Symptom	Likely area	Example part for 66513293K112
Won’t drain / standing water	Drain system	Dishwasher drain pump WPW10348269
Not filling / low water	Fill system	Dishwasher water inlet valve W11175771
Poor drying / water left on dishes	Heat and rinse aid	Dishwasher heater W10703867
Upper rack won’t adjust / sags	Rack hardware	Dishrack adjuster kit W10712394

Why it matters

A correct repair decision saves money and time; it also prevents repeat issues caused by installation problems (leveling, securing to the countertop, and proper water and drain routing) that can mimic part failures.

Last updated: February 2026

Yes. The Kenmore 66513293K112 Ultra Wash dishwasher uses a filtration system in the bottom of the tub to catch food soil and help protect the pump and spray system; you can remove the filter pieces for routine cleaning using the steps in the 66513293K112 owner’s manual.

Where the filter is and what it does

Most Kenmore undercounter dishwashers of this design have a multi-piece filter assembly at the bottom of the tub, under the lower rack.

• Helps keep larger debris out of the sump and pump area
• Improves wash performance by keeping spray paths clearer
• Reduces drain clogs and standing water issues
• Needs periodic cleaning if you see grit, odors, or poor cleaning

How to remove and clean the filter (typical steps)

Use these steps as a practical guide; match the exact filter style and locking direction to the 66513293K112 owner’s manual.

• Pull out the lower rack for access.
• Turn the upper filter assembly about a quarter turn counterclockwise to unlock.
• Lift out the upper filter.
• Grasp and lift out the lower filter (some styles pull slightly forward first).
• Rinse under running water until most soils are removed; use a soft brush if needed.
• Reinstall both pieces and lock the upper filter fully before running a cycle.

Quick troubleshooting: when the filter is the likely cause

Symptom	What the filter can cause	What to do first
Grit on dishes	Soil recirculates	Clean filter and run a rinse cycle
Slow draining	Debris restricts sump flow	Clean filter; check drain path
Odor	Trapped food soils	Clean filter; run hot cycle
Poor spray	Debris affects circulation	Clean filter; inspect spray arm holes

If you still have draining problems after cleaning, the drain system may need attention (for example, a restricted hose or a weak pump). For this model, common drain-related parts include the dishwasher drain pump WPW10348269 and the dishwasher drain hose 8269144A.

Why it matters

A clean filter helps your Kenmore 66513293K112 maintain strong water circulation and reliable draining, which directly affects cleaning results, cycle time, and odor control.

Last updated: February 2026

Common problems we see with the Kenmore 66513293K112 dishwasher include poor cleaning, not draining, leaking, and control or Start/Resume issues. Many of these come down to water supply, loading, filters, spray circulation, or a drain restriction; our 66513293K112 installation guide also highlights basic checks like power, door latch, and water being turned on.

Most common symptoms (and what they usually point to)

• Not cleaning well: clogged spray arm holes, dirty filter, overloading, low water temperature, or weak wash circulation
• Not draining: kinked/blocked drain hose, clogged sump/filter area, or a failing drain pump
• Leaking: loose hose connections, door not sealing, or water line issues
• Buttons/controls not working: user interface or control board problem, or door not fully latched
• Start/Resume light flashing: door not closed within the required time after pressing Start/Resume

Quick checks we recommend first

1. Confirm the water supply is on and the dishwasher fills; the install instructions suggest checking for water in the tub early in a short cycle.
2. Make sure the door closes tightly and latches.
3. Clean the filter area; a restricted filter can cause both poor cleaning and drain problems.
4. Inspect the drain path for kinks or clogs; if you use a braided supply hose, plan to replace it on a 5-year schedule.
5. If the door drops open or closes too fast, adjust door tension as described in the install guide.

Parts that commonly solve these issues on this model

Symptom	Common part to check	Example part for 66513293K112
Not draining	Drain pump	Dishwasher drain pump WPW10348269
Poor cleaning	Spray arm, filter	Dishwasher spray arm WPW10491331, dishwasher filter W10872845
Not filling or fills slowly	Water inlet valve	Dishwasher water inlet valve W11175771
Leaking at drain connection	Drain hose	Dishwasher drain hose 8269144A

Why it matters

Catching the root cause early prevents repeat wash failures and helps avoid secondary damage, like a motor working harder due to restricted water flow or a drain backup that leads to standing water and odors.

Last updated: February 2026